Aerpro AP15AQI User manual

vent/suction mount
Wireless Charging Kit
USER MANUAL AP15AQI
Thank you for purchasing the AP15AQI Wireless Charging Kit.
It is compatible with all Qi enabled devices like Samsung S7/
S7 edge, S8/ S8 edge, iPhone8, iPhone8 plus, iPhoneX, etc.
For optimum performance and safety, please read this manual
carefully before using this product.
www.aerpro.com

• Automatic lock and release
• Silicone pad for anti-scratching
• Built-in 250mAh battery
• Power: 10W
• Temperature control sensor
• Over voltage/temperature protection
• Type-C Input
• Input Voltage: 9V/1.67A; 9V/1.34A
• Output Voltage: 9V/1.12A; 9V/0.83A
• Size: 118.3 x 71.9 x 20.3 mm
• Operating frequency range: 110-205KHz
• Charging efficiency: ≤70%
• Transmission distance: ≤6mm
• Weight: 121.6g
Qi-ID3991
Infrared Sensor
for Locking
Extendable
Arm
Wireless
Charging
Area
Wireless
Charging
Indicator
Type-C Input
Air Vent
Clamp
Touch Button
for Releasing
Power
Button
Power
Indicator
AP15AQI Features:
Specifications:

Step 1:
Attaching the vent clamp to the charging body
Loosen the nut
Tighten the nut to complete
installation
Press to open
Press button on vent clamp to open
grip arms, then place mount on vent.
Release button to secure on vent
Place the nut over the ball on the vent
mount. Press ball into charging base.
How to Use Vent mount:

Step 1:
Attaching the suction mount to the charging body, by placing
the nut over the ball on the suction mount. Press ball into
charging base, then tighten the nut to complete installation
How to Use Suction mount:
Step 2:
Clean the surface you want to attach the suction mount to
with a clean rag or an alcohol wipe. Release the locking tab
on the suction mount. Remove the clear sticker from the
base. Press the suction mount firmly on the cleaned surface
and press locking tab down to lock in position. Use knobs on
suction mount to adjust angle and length of telescopic arm.

Using your device:
Step 1:
Use the USB Type-C cable to connect to the USB power of
the car or car charger
Not included

Step 2:
Press “Power button” to power on
Step 3:
Touch the top of the vent mount (Touch button) to
automatically release the grip arms

Step 4:
Automatically locks grip arms once the IR sensor is triggered
by phone proximity
NOTE: Due to different phone sizes, the wireless charging contact area
may vary. Adjust the feet by pulling down to allow alignment between the
phone and the wireless charger contact area.

Step 5:
Touch the top of the vent mount (Touch button) to automati-
cally release the grip arms to remove phone

Step 7:
Alternatively press the power button for 3 seconds to turn the
wireless charger completely off.
Step 6:
The AP15AQI grip arms will automatically lock after 5
minutes when not being used.

AP15AQI Holder Indicator light explained
Wireless Charging light explained
ON
Slow Blinking
Fast Blinking
Slow Pulsing
Fully Charged
Charging
Low Power
Ready to Start
ON
Slow Blinking
Fast Blinking
Slow Pulsing
Wireless Charging
Error, Reposition Phone
Standby
Phone Fully Charged
TIPS:
When using this product it must be connected to power. To achieve fast
charging, a QC2.0/3.0/4.0 car charger is required. Aerpro models
APL24QC & ADMQC3U meet the requirements are sold separately.

PRECAUTIONS:
• Keep the product dry. Rain, moisture and various liquids may contain
minerals that will corrode the circuit. If the product gets wet, dry it as soon
as possible or use a soft cloth to wipe it clean.
• When charging use a 5V/2A, 9V/2A charger. Do not use a lesser
specification charger as the product with not operate correctly and will
damage the product. Do not use damaged chargers.
• Do not attempt to charge the product with the battery exposed or with a
broken case. Do not charge the product with incompatible equipment.
• Do not store the product in a cold place. Otherwise when temperature
rises to normal temperature, moisture will build up inside and may
damage the electrical appliance.
• Do not attempt to open the product, unauthorized dis-assembly or
modification will damage the equipment and or related wireless charging
functions.
• Do not throw, tap or shake the product; rough handling of the product
will damage the internal circuit board and the mechanical structure.
• Use a clean moist soft cloth to clean the surface of the product. Do not
use or store the equipment in dusty or dirty environments.
• Some components of this product are magnetic and metal materials
may be absorbed onto this product. Please do not use bank cards, credit
cards or any other items with magnetic near the product so as to avoid
losing the data stored due to demagnetization.

NOTE:
1. The car charger or adapter used to power the Wireless Charging Kit
that outputs the proper voltage is required (Not included). It should meet
QC2.0, QC3.0 or QC4.0 standard. Aerpro models APL24QC & ADMQC3U
meet the requirements are sold separately.
2. The connected power car charger used must output 9V/1.67A. Using a
charger or adapter with a lower output may result in malfunction or
overheating.
3. Quick Charge 3.0 power charger is required for fast charge mode
4. Charging speed may vary depending on device specifications, input
voltage and environment.
5. Phone cases or metal plates for magnetic attachment may interfere
with wireless charging.
6. It’s normal for the charger and your charging device to get hot whilst
charging, and hotter when being used at the same time. Remove device
from charging pad to allow to cool down and avoid over heating.
TECHNICAL ASSISTANCE
If you need assistance setting up or using your Aerpro product now or in
the future, call Aerpro Support Australia TEL: 03 – 8587 8898 FAX: 03 –
8587 8866
Mon-Fri 9am – 5pm AEST
If you would like to download a digital copy of this manual, or other Aerpro
manuals/software, please visit the http://aerpro.com website.
This manual is considered correct at time of printing but is subject to
change. For latest manuals and updates refer to the website.
www.aerpro.com