AES PROTEAM G-Silent G108 User manual

PROTEAM G-Silent Inverter
User Manual
Automated Environmental Systems Ltd.
Unit 1, 1 Wimbledon Avenue, Brandon, Suffolk, IP27 0NZ
01842 819130 | [email protected]

Table of contents
A. Foreword 1
B. Safety Precautions 2
1. Warning 2
2. Attention 3
3. Safety 3
C. About your eat pump 4
1. Transportation 4
2. Accessories 4
3. Features 5
4. Operating range 5
5. Operating modes 5
6. Technica parameters 6
7. Dimension 7
D. Installation guidance 8
1. Insta ation reminder 8
2. Wiring 9
3. E ectrica wiring diagram 10
4. References for protecting devices and cab e specification 10
E. Instructions for Operation 11
1. Key Function 11
2. Operation Instruction 12
F. Testing 14
1. Inspect heat pump before use 14
2. Leakage detection notice and method 14
3. Tria 15
G. Maintenance 16
H. Trouble s ooting for common faults 17
I. Water pump control connection 20
J. Wi-Fi operation 24

G-Model Inverter Heat Pump 1
A. Foreword
Thank you for choosing our inverter pool heat pump, which is designed to be more silent and more
energy-efficient than all previous models
We hope you'll be able to enjoy your pool for longer now!
Thank you!

G-Model Inverter Heat Pump
B.
Safety Precautions
This manual contain important safety instructions
Please always read and obey all safety instructions
Environmentally-
friendly R32 Refrigerant is used for t is eat pump
1. Warning
The WARNING sign
practice, or the
result in
extremely important
a
Keep the heat pump away from fire source
b
The heat pump must be placed in well
it indoors or in a closed area
c
Repair and disposal must be carried out by trained service personnel
d
Vacuum the unit completely before welding Welding can only be carried out by
professional personnel in service cente
Safety Precautions
This manual contain important safety instructions
Please always read and obey all safety instructions
friendly R32 Refrigerant is used for t is eat pump
The WARNING sign
denotes a hazard It calls attention to a procedure,
practice, or the
like, which, if not correctly performed or adhered to, could
result in
personal injury or injury to a third party These signs are rare but are
extremely important
Keep the heat pump away from fire source
The heat pump must be placed in well
-ventilated area,
it is not permitted to install
it indoors or in a closed area
Repair and disposal must be carried out by trained service personnel
Vacuum the unit completely before welding Welding can only be carried out by
professional personnel in service cente
r
2
denotes a hazard It calls attention to a procedure,
like, which, if not correctly performed or adhered to, could
personal injury or injury to a third party These signs are rare but are
it is not permitted to install
Repair and disposal must be carried out by trained service personnel
Vacuum the unit completely before welding Welding can only be carried out by

G-Model Inverter Heat Pump 3
2. Attention
a Please read the following instructions before installation, use and maintenance
b Installation must be done by professional staff only in accordance with this manual
c Leakage test must be performed after installation
d Please don’t stack substances close or on the heat pump, which will reduce efficiency or damage the
heat pump
e If a repair is required, please contact the nearest after-sales service center The repair process must
be strictly in accordance with the manual All repair practice by non-professional is prohibited
f Don’t use or stock combustible gas or liquid l block air flow near inlet or outlet area, otherwise the
efficiency of the heat pump will be reduced, or the unit could even stop working
g Set proper temperature in order to get comfortable water temperature to avoid overheating or
overcooling
h In order to optimize the heating effect, please ensure that the pipes between the swimming pool and
the heat pump are insulated to reduce heat loss It is also recommended that a suitable pool cover
be installed on the pool at all times when the pool is not in use
i For maximum efficiency, the connecting pipes between the pool filter and the heat pump should be
insulated and as short as practically possible: if over 10m extra thick insulation on the waterpipe is
recommended
j Do not accelerate the defrosting process by any means other than recommended by manufacturer,
3. Safety
k Please keep the main power supply switch far away from the children
l When a power cut happens during operating, and later the power is restored, the heat pump will
m start up
n During stormy weather switch off the main power supply and disconnect the power to the heat pump
to prevent any damage that could be caused by lightning
o A safety inspection must be carried out before the maintenance or repair of heat pumps with R32 gas
in order to minimize the risk for fire
p Installation and repairs should be carried well-ventilated areas No ignition sources (sparks or flames)
are allowed near the unit while it is in operation
q If there is any R32 gas leak during the installation process, stop all operations immediately and call
the service center

G-Model Inverter Heat Pump 4
C. About your eat pump
1. Transportation
a Always keep upright
b Do not lift at or position the heat pump by holding the
water connection/union
(Otherwise the titanium heat exchanger may be damaged)
2. Accessories
Connection of t e condensate drainage kit:

G-Model Inverter Heat Pump 5
3. Features
a DC Twin-rotary inverter compressor (Mitsubishi)
b DC Brushless fan motor
c EEV Technology
d Reverse-cycle defrosting with 4-way valve
e High efficiency twisted titanium heat exchanger
f Sensitive and accurate temp control and water temp display
g High-pressure and low-pressure protection
h Full protection on electrical system
4. Operating range
The heat pump can work between air -10°C～43°C, and its ideal operating range is at an air temperature
between 15°C ~ 25°C
5. Operating modes
aThe heat pump has two modes: Boost and Silence
b They have different strengths under different conditions
Mode Modes Strengt
Boost mode
Heating capacity: 20% to 100% capacity
Intelligent optimization
Fast heating
Silence mode
Heating capacity: 20% to 80% capacity
Sound level: 3dB (A) lower than Boost mode

G-Model Inverter Heat Pump 6
6. Tec nical parameters
Remarks:
This heat pump can perform normally at an air temperature between -10°C～+43°C: efficiency cannot be guaranteed out of this operating range
Please note that the pool heat pump performance and parameters are different under various conditions
Related parameters are subject to adjustment periodically for technical improvement without further notice For details please refer to nameplate
Model G108 G110 G112 G115 G117 G120 G125 G130 G130T G135T
PERFORMANCE CONDITION: Air 27°C/ Water 27°C/ Humid. 80%
Heating
capacity(kW)
7 0 9 0 11 0 13 0 15 0 17 5 21 0 28 0 28 0 35 2
COP Range 14 0~7 2 14 0~7 2 14 0~7 0 14 5~7 0 15 0~7 0 15 6~7 0 14 8~7 1 16 0~7 2 15 8~7 1 15 5~7
PERFORMANCE CONDITION: Air 15°C/ Water 26°C/ Humid. 70%
Heating capacity(kW)
5 0 6 6 7 7 9 0 10 5 12 5 14 5 19 0 19 0 24 2
COP Range 7 3~4 5 7 5~4 8 7 3~4 7 7 5~5 0 7 7~4 9 7 7~5 0 7 1~5 0 8 0~5 0 8 0~5 0 7 5~5
TECHNICAL SPECIFICATION
Advised pool
surface (m2) * Wit
Cover
15~40 20~60 30~75 35~90 40~100 40~110 50~125 60~160 60~175 85~200
Operating air
temperature (°C)
-10°C~43°C
Power supply 230V 1Ph 400V 3Ph
Rated input power
(kW)
0 14~1 12 0 19~1 38 0 22~1 64 0 26~1 8 0 28~2 15 0 33~2 50 0 38~2 90 0 49~3 80 0 49~3 80 0 65~4 84
Rated input
current (A)
0 61~4 83 0 83~5 98 0 96~7 13 1 13~7 83 1 22~9 32 1 44~10 9 1 66~12 7 2 15~16 53 0 71~5 51 0 95~7 01
Sound level at 10m
dB(A)
16 5~26 0 16 8~26 1 16 6~27 9 20 1~28 7 19 3~32 21 1~31 8 18 9~32 2 21 5~32 9 21 5~32 9 20 6~32 6
Advised water flow
(m³/ )
2~4 2~4 3~5 4~6 5~7 6~8 8~10 10~12 10~12 12~18
Water connection
(mm)
50

G-Model Inverter Heat Pump 7
7. Dimension
E
D
C
FG
A
H
B
※Above data is subject to modification for technical improvements/ reasons without notice
Note: The picture above is the specification diagram of the pool heat pump, for technician’s installation
and layout reference only The product is subject to adjustment periodically for improvement without
further notice
A B C D E F G H
G108 410 645 404 430 890 250 75 658
G110 410 645 404 430 890 250 75 658
G112 410 645 404 430 890 290 75 658
G115 410 645 404 430 890 280 75 658
G117 410 645 404 430 970 320 75 658
G119 410 710 404 430 1060 320 75 658
G125 410 710 404 430 1060 460 75 758
G130 410 710 404 430 1060 640 75 958
G130T 410 710 404 430 1060 640 75 958
G135T 492 950 486 512 1314 650 75 958
Name
Size(mm)
Model

G-Model Inverter Heat Pump 8
D. Installation guidance
1. Installation reminder
Only professionals are allowed to install the heat pump End users who are not qualified professionals
should not install by themselves, otherwise the heat pump could be damaged and risky for users’ safety
a Location and water pipe connection
The heat pump should be installed in a well-ventilated place
1000mm

G-Model Inverter Heat Pump
9
1) The frame must be fixed with bolts (M10) to concrete foundation or brackets The concrete foundation
must be solid and secure; the brackets must be strong enough and have antirust treatment
2) Please don’t place objects that could block the air flow near the inlet or outlet area; there should be no
obstructions within at least 50cm (500mm / 20”) of the back, and sides of the unit (see figure above),
or the efficiency of the heat pump could be reduced or it could even not work at all;
3) In order to function the unit needs to be installed as part of a system with a filtration pump (to be
provided by the user): for the recommended water flow of the circulation pump please refer to the
Technical Specifications of the heat pump
4) When the machine is running, there will be condensation water from the bottom Please place the
drainage nozzle (accessory) into the hole and connect a hose to drain the condensation water away
b The inlet and outlet water unions can’t stand the weight of soft pipes The heat pump must be
connected with hard pipes!
2. Wiring
a Connect to appropriate power supply, the voltage should comply with the rated voltage of the
products
b Earth the machine well
c Wiring must be handled by a professional technician according to the circuit diagram
d If leakage protector set it (use protector) according to the local regulation of allowed mA
e. The layout of power cable and signal cable should be separated from each other

G-Model Inverter Heat Pump
10
3. Electrical wiring diagram
a. For power supply: 230V 50Hz
b. For power supply: 400V 50Hz
Note：
1) Must be hard wired, plug is not allowed
2) The heat pump must have a good ground connection (earth)
4. References for protecting devices and cable specification
※ Above data is subject to modification without notice
Note: The above data is calculated for a power cable of length ≤ 10m Voltage drop on power cable must
be less than 10 Volt when the heat pump is at full load For longer cables the diameter (mm
2
) must
be increased The signal cable can be extended to 50m maximum
MODEL
G108 G110 G112 G115 G117 G119 G125 G130 G130T G135T
Breaker
Rated Current
(A)
9 10 5 12 14 5 16 5 18 21 24 9 12
Rated Residual
Action Current
(mA)
30 30 30 30 30 30 30 30 30 30
Fuse (A)
9 10 5 12 14 5 16 5 18 21 24 9 12
Power Cord (mm
2
)
3x1 5 3 x 2 5 3 x 2 5 3 x 2 5 3 x 2 5 3 x 4 3 x 4 3 x 6 5 x 2 5 5 x 2 5
Signal cable (mm
2
) 3×0 5 3×0 5 3×0 5 3×0 5 3×0 5 3×0 5 3×0 5 3×0 5 3×0 5 3 x 0 5
Distribution Box (provided by customer)
Earthing
Power Supply
230V 50Hz Breaker
Fuse
Power Cable Swimming Pool Heat Pump Wiring Board
Distribution Box (provided by customer)
Power Supply
400V 50Hz
Earthing Breaker
Fuse
Power Cable Swimming Pool Heat Pump Wiring Board

G-Model Inverter Heat Pump
11
E. Instructions for Operation
1. Key Function
Symbol Heating & cooling models
1 Power On/Off
2 Wi-Fi setting
1 Lock/Unlock Screen
2 Heating mode (18-40°C)
3 Cooling mode (12-30°C)
4 Auto mode (12-40°C)
1 Boost
2 Silence
Temperature Setting
Attention:
i The controller has power-down memory function
ii. The buttons will turn dark when it’s locked

G-Model Inverter Heat Pump
12
2. Operation Instruction
a. Screen Lock
1) Press “ ” for 3 seconds to lock or unlock the screen
2) Automatic Lock Period: 30 seconds if no operation
b. Power On
Press “ ” for 3 seconds to unlock screen Press “ ” to power on machine
c. Temperature Setting
Press “ ” and “ ” to display and set temperature
d. Mode Selection
1) Heating/Cooling/Auto
Press “ ” to switch between heating” ”, cooling ” ” and auto mode ” ”
Heating mode “ ”: Water temperature setting range(18-40°C)
Cooling mode “ ”: Water temperature setting range(12~30°C)
Auto mode “ ”: Water temperature setting range(12~40°C)
* When water inlet temperature is 1°C higher than set point, automatic cooling mode starts
* When water inlet temperature is 1°C lower than set point, automatic heating mode starts
2) Silence/Boost mode selection
Press “ ” to switch among boost mode , silence mode
Default mode: boost
Please choose boost mode for initial heating

G-Model Inverter Heat Pump
13
e. Wi-Fi “ ” (refer to instructions at t e back of t e manual)
When the screen is on, press “ ”for 3 seconds; when “ ” is flashing, enter Wi-Fi connection
Connect the Wi-Fi on your mobile phone and enter a password, then it will be possible to control the
unit by Wi-Fi using the APP When the APP is successfully connected to Wi-Fi，the “ ” icon
remains on
f. Defrosting
1) Automatic defrosting: when machine is auto defrosting, will flash, and return to previous
working mode when it finishes
2) Manual Defrosting: To enter forced defrosting mode, the compressor must be working for more
than 10 minutes in heating mode, press “ ” and “ ” on touch controller simultaneously
for 5 seconds to start forced defrosting, when ” ” flashes the defrost cycle starts, when “ ”
stops flashing the defrost cycle stops
(Remarks: the interval between manual defrosting cycles should be more than 30 minutes )

G-Model Inverter Heat Pump
14
F. Testing
1. Inspect eat pump before use
a The ventilating device and outlets are operating adequately and are not obstructed
b It is prohibited to install refrigeration pipe or components in corrosive environment
c Inspect the electrical wiring according to the electrical wiring diagram and ground
connection
d Double-check that the main power supply to the unit is off
e Check the air inlet and outlet
2. Leakage detection notice and met od
a Leakage checking is prohibited in closed areas
b Naked flames are prohibited during the leakage inspection A halide torch (or any
other detector using a naked flame) must not be used
c Leakage detection fluids can be applied with most refrigerants but the use of detergents containing
chlorine must be avoided as the chlorine may react with the refrigerant and corrode the copper pipe
d Vacuum completely before welding Welding can only be carried out by professional personnel in
service center
e If there is any gas leakage, please stop using the unit and contact professional a service center

G-Model Inverter Heat Pump
15
3. Trial
a The user must “Start the swimming pool filtration pump before the unit and turn off the unit before
stopping the pool filtration pump”, or the machine will be damaged
b Before starting the heat pump, please check for any water leakage
c In order to protect itself, the heat pump is equipped with a time lag starting function: the fan will start
working 1 minute before the compressor when starting the machine, and it will stop running 1
minute after the compressor when the machine is switched off
d After starting up heat pump start up, please check for any strange noise from the machine

G-Model Inverter Heat Pump
16
G. Maintenance
1 In winter, when the heat pump is not in use:
a Cut off power supply to prevent any damage to the unit
b Drain all water clear from the unit Make sure all water is out.
c Cover the unit when not in use
2 Please clean the unit with household detergents or clean water, NEVER use gasoline, thinners or
any aggressive cleaning liquid
3 Check bolts, cables and connections regularly
4 If repair or disposal of the unit is required, please contact the nearest authorized service center
5 Do not attempt to work on the equipment by yourself Improper operation can be dangerous
6 A safety inspection must be carried before any maintenance or repair work is carried out on heat
pumps with R32 gas
!!Important:
Unscrew and disconnect the water
nozzle of inlet pipe to let the water
flow out.
If/when the water inside machine freezes in
winter season, the titanium heat exchanger
may be damaged.
“CUT OFF”
power supply to t e eat pump
before cleaning, examination and repair

G-Model Inverter Heat Pump 17
H. Trouble s ooting for common faults
1. Repairing Guidance
-----------------------------------------------------------------------------------------------------------------------------------------
WARNING:
a) If repair or disposal of the unit is required, please contact the nearest
authorized service center
b Requirements for Service Personnel
c Technicians involved with any kind of work involving the refrigerant circuit should hold a current valid
certificate/qualification from an industry-accredited authority, which authorizes them to handle
refrigerants safely in accordance with industry-recognized standards and regulations
d Do not attempt to work on the equipment by yourself Improper operation can be dangerous
e Strictly comply with the manufacturer's requirements when charging R32 gas and carrying out
equipment maintenance This chapter focuses on special maintenance requirements for swimming
pool heat pump with R32 gas Please refer to the technical service manual for detailed maintenance
operation
f Vacuum completely before welding Welding can only be carried out by professional personnel

G-Model Inverter Heat Pump
18
2. Failure solution and code
----------------------------------------------------------------------------------------------------------------------------------------
Failure Reason Solution
Heat pump doesn’t run
No power Wait until the power is back on
Power switch is off Switch on the power
Fuse burned Check and change the fuse
The breaker is off Check and turn on the breaker
Fan running but wit
insufficient eating
Evaporator blocked Remove obstructions
Air outlet blocked Remove obstructions
3 minutes start delay Wait patiently
Display normal, but no eating
Set temp too low Set proper heating temp
3 minutes start delay Wait patiently
If above solutions don’t work, please contact your installer with detailed information and your model
number Don’t try to repair it yourself
Note: If the following conditions happen, please stop the machine immediately, and cut off the power
supply immediately, then contact your dealer:
1 Inaccurate switch action
2 The fuse is frequently broken, or the circuit breaker trips