Aetina AN110-XNX-EN70 User manual

Quick Start Guide
Edge AI System Kit AN110-XNX/XNX16-EN70
WHAT’S IN THE KIT?
1 x AN110-XNX/XNX16-EN70 system
Ubuntu 18.04
NVIDIA® Jetson Xavier™ NX module
1 x power adaptor with 12VDC, 5A
1 x EU power cord
1
2
3
4
5
GET READY
STEP 1
CONNECT HARDWARE
STEP 2
SETUP DETAILS
STEP 3
Prepare the materials below
A monitor with HDMI and respective cables
USB keyboard and mouse
Ethernet cable
Check if AN110-XNX/XNX16-EN70 Edge AI System Kit comes with passive cooling design,
NVIDIA Jetson Xavier NX module, NVIDIA Jetpack package and Ubuntu 18.04 operating system
Follow the instructions carefully before connecting cables and powering on
1. Connect to the monitor while powering off
2. Power on and automatically enter the OS
3. Log in to the Ubuntu 18.04 OS via credentials below
Username: nvidia
Password: nvidia
*Caution high temperature:The high-performance system heats up in operation
Any question please contact us : www.aetina.com
Connect to
Ethernet cable
Connect to USB
mouse/keyboard
Connect to
monitor
Connect to
power adaptor

Product Specifications
Safety Precaution FCC Statement
Please follow the below safety instructions carefully. It is advised that you keep this
quick start guide for future references.
1. Take note of all cautions and warnings on the device
2. Make sure the power source matches the power rating of the device
3. Position the power cord so that people do not step on it. Do not place anything
over
the power cord
4. Always completely disconnect the power before working on the system
5. Do not make any connections while the device is powered on. A sudden rush of
power may damage sensitive electronic components
6. If you will not use the device for a long time, disconnect the power to avoid
damage by transient over-voltage
7. Always disconnect this device from any power supply before cleaning
8. While cleaning. use a damp cloth instead of liquid or spray detergents
9. Make sure the device is installed near a power outlet and easily accessible
10. Keep this device away from humidity
11. Place the device on a solid surface during installation to prevent it from falling
12. Do not cover the openings on the chassis. This is to ensure optimal heat dissipation
13. Keep an eye for high temperatures when the system is running
14. Do not touch the heat sink or heat spreader when the system is running
15. Never pour any liquid into the openings, or may causing fire or electric shock
16. Most of the electronic components are sensitive to static electrical charge, be sure
to ground yourself
when installing internal components in any static-shielded containers
17. If any of the following situations arise, please contact our service personnel:
I. Damaged power cord or power supply
II. Liquid intrusion through the device
III. Exposure to moisture
IV. Device is not working as expected or in a manners as described in this quick start
guide
V. The device is dropped or damaged
VI. Any obvious signs of damage on the device
18. Do not operate the device beyond 55°C(131°F)
19. Store the device from -40°C to 80°C (-40℉to 176℉)to prevent damage
This device complies with Part FCC Rules.
Operation is subject to the following two
conditions:
(1) this device may not cause harmful
interference, and (2) this device must accept
any interference received including interference
that may cause undesired operation.
Caution: There is a danger of explosion if the
battery is incorrectly replaced. Replaced only
with the same or equivalent type
recommended by the manufacturer. Dispose of
used batteries according to the manufacturer’s
instructions and your local government’s
recycling or disposal directives.
Attention: II y a u risque d’explosion si la
batterie est remplacée de façon incorrecte.
Nela remplacer qu’ avec le même modèle ou
équivalent recommandé par le construteur.
Recycler les batteries usées en accord avec les
instructions du fabrucant et les directives
gouvernementales de recyclage.
AN110-XNX-EN70
21 TOPS
NVIDIA Jetson Xavier NX
1 x RJ-45
Please visit Aetina official website (www.aetina.com)
1 x HDMI Type A
5 x GPIO (DB9 female connector) , 1x RS-232 , 2 x UART , 1 x I2C (DB9 connector)
2 x USB3.2 Gen1 Type A
1 x USB2.0 AB OTG
1 x Micro SD slot
1x M.2 E-key 2230 : Wifi
DC-in 12V, DC Jack
-20°C to 55°C(-4°F~ 131°F) / Storage Temperature:-40°C to 80°C(-40°F~ 176°F)
5% ~ 90% (non-condensing)
880g(1.94Ib)
wall mount (optional)
120 x 72.5 x 100mm (4.72" x 2.85" x 3.94")
1 x Power button
Module
AI Performance
Storage
Jetpack Version
Display
LAN
USB
MISC. Function
MISC. Function
Expansion
Power Input /Connector
Temperature
Humidity
Storage
Dimension (W x D x H)
Weight
Mounting
16 GB eMMC 5.1 flash
CE/FCC Class A
Certification
Model Number
Ubuntu 18.04OS Support
Regulatory