AG Neovo F-417 User manual

<12005442 001> Page 2 of 78
TRF No.: I950___E TRF originator: FIMKO
Particulars: test item vs. test requirements
Equipment mobility .....................................................: Moveable
Operating condition .....................................................: Continuous
Tested for IT power systems ......................................: Yes
IT testing, phase-phase voltage (V) ...........................: IT, 230V for Norway
Class of equipment ....................................................: Class I
Mass of equipment (kg) ..............................................: 4.76kg
Protection against ingress of water ............................: IPX0
Test case verdicts
Test case does not apply to the test object ...................:
N(.A.)
Test item does meet the requirement............................:
P(ass)
Test item does not meet the requirement......................:
F(ail)
General remarks
”This report is not valid as a CB Test Report unless appended to a CB Test Certificate issued by a
NCB, in accordance with IECEE 02”.
This report shall not be reproduced except in full without the written approval of the testing laboratory.
The test results presented in this report relate only to the item tested.
”(see remark #)" refers to a remark appended to the report.
"(see Annex #)" refers to an annex appended to the report.
Throughout this report a point is used as the decimal separator.
Note
Australia is not included in the list of the countries according to CB Bulletin 103A (July 2002). However, the
modified standard IEC 60950:1999 was published as AS/NZS 60950:2000. Variations as outlined in Annex
ZZ of that n
ational standard were not published yet in the latest CB Bulletin but were appended to the
section of national differences of this test report.
Comments
These equipment is a 17” LCD monitor for general office use. All models are identical except for model
designation only. In model designation, the X can be 0-9, A-Z or blank for marketing purpose.
The internal building-in switching power supply (SPS) was evaluated with this equipment, see appended
table 1.5.1 for detail information.
All tests were carried out with model GXX7X to represent the other model if no else specified.
The test sample is a pre-production without serial number.

<12005442 001> Page 3 of 78
TRF No.: I950___E TRF originator: FIMKO
Copy of marking plate(s):

<12005442 001>
Page 4 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
1 GENERAL P
1.5 Components P
1.5.1 Comply with IEC 60950 or relevant component
standard Components, which were found to affect safety aspects,
comply with the requirements
of this standard or within the
safety aspects of the relevant
IEC component standards
(see appended table 1.5.1).
P
1.5.2 Evaluation and testing of components Components, which are
certified to IEC and/or
national standards, are used
correctly within their ratings or
had been evaluated during
this approval.
P
Dimensions (mm) of mains plug for direct plug-in : Equipment is not direct plug-
in type. N
Torque and pull test of mains plug for direct
plug-in; torque (Nm); pull (N)................................:
dto N
1.5.3 Thermal controls No thermal controls provided. N
1.5.4 Transformers Transformers used are
suitable for their intended
application and comply with
the relevant requirements of
the standard.
P
1.5.5 Interconnecting cables Interconnection cables to be
provided with the equipment
are carrying signals on energy
level below 240VA.
Besides for the insulation
materials there are not other
requirements for the
interconnection cables.
P
1.5.6 Capacitors in primary circuits ...............................: Between the lines one
capacitor subclass X2
according to IEC 60384-
14/1993 with 21 days damp
heat test. Between line and
ground: Y2 capacitor
according to IEC 60384-
14:1993.
P
1.5.7 Double or reinforced insulation bridged by
components Primary and secondary
bridged by one capacitor
(C800).
P

<12005442 001>
Page 5 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
1.5.7.1 Bridging capacitors C800 is certified as Y1
capacitor according to IEC 60
384-14/1993
P
1.5.7.2 Bridging resistors N
1.5.7.3 Accessible parts The output connector is
designed as limited current
circuit (see sub-clause 2.4).
P
1.5.8 Components in equipment for IT power systems Phase to earth designed in
according to phase-to-phase
working voltage. The Y2 type
capacitor used between
phase-to-earth is rated
according.
P
1.6 Power interface P
1.6.1 AC power distribution systems .............................: TN power system. IT power
system for Norway. P
1.6.2 Input current Highest load according to
1.2.2.1 for this equipment is
the operation of the equipment
at full white pattern and sound
card on maximum volume.
Results see appended table
P
1.6.3 Voltage limit of hand-held equipment This appliance is not a hand-
held equipment. N
1.6.4 Neutral conductor The neutral is not identified in
the equipment. Basic
insulation for rated voltage
between earthed parts and
primary phases.
P
1.7 Marking and instructions P
1.7.1 Power rating See below. P
Rated voltage(s) or voltage range(s) (V) .............: 100-240V~ P
Symbol for nature of supply for d.c. .....................: AC supply. N
Rated frequency or frequency range (Hz) ...........: 50/60Hz P
Rated current (mA or A) ......................................: 1.2A P

<12005442 001>
Page 6 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
Manufacturer’s name/Trademark ........................: 1). Not shown/ COMPAL
trademark
2). ASSOCIATED
INDUSTRIES CHINA
INC./ AG neovo
trademark
P
Type/model ..........................................................: GXX7X
(X=0-9, A-Z or blank)
P
Symbol of Class II ................................................: Class I equipment N
Other symbols .....................................................: Other symbols do not give
rise to misunderstanding. P
Certification marks ...............................................: See copy of the marking plate
for the safety marks. P
1.7.2 Safety instructions 7UGTKPUVTWEVKQPRTQXKFGF P
1.7.3 Short duty cycles Equipment is designed for
continuous operation. N
1.7.4 Supply voltage adjustment ..................................: Full range circuit design. N
1.7.5 Power outlets on the equipment ..........................: No standard power outlets
provided. N
1.7.6 Fuse identification ................................................: Fuse marking on PCB near
fuse:
F801 T3.15A /250V
P
1.7.7 Wiring terminals See below. N
1.7.7.1 Protective earthing and bonding terminals Appliance inlet provided. N
1.7.7.2 Terminal for a.c. mains supply conductors The equipment is provided
with appliance inlet, which is
for connection of a detachable
type power supply cord.
N
1.7.8 Controls and indicators See below. 
1.7.8.1 Identification, location and marking .....................: The indication of the power
switch and stand-by touch
button is placed above it.
P
1.7.8.2 Colours ...............................................................: The colours of the LED
indicator are as follows:
x green – ON condition
x amber – stand-by mode
P
1.7.8.3 Symbols according to IEC 60417 .........................: Symbol No. 5009 according to
IEC 60417 is placed above the
stand-by touch button.
P

<12005442 001>
Page 7 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
1.7.8.4 Markings using figures .......................................: Not used. N
1.7.9 Isolation of multiple power sources .....................: Equipment designed for only
one connection to the mains. N
1.7.10 IT power system For Norway compliance has
to be evaluated during the
national approved.
N
1.7.11 Thermostats and other regulating devices Neither thermostats nor other
regulating devices provided. N
1.7.12 Language .............................................................: Installation instruction and
markings are in English.
User’s Manual in English.
Versions of other languages
will be provided when
submitted for national
approval.
P
1.7.13 Durability The marking plate was
subjected to the permanence
of marking test. The marking
plate was rubbed with cloth
soaked with water for 15s and
then again for 15s with the
cloth soaked with petroleum
spirit.
After this test there was no
damage to the marking. The
marking on the label did not
fade. There was no curling of
the marking.
P
1.7.14 Removable parts No removable parts provided. N
1.7.15 Replaceable batteries No batteries provided. N
Language..............................................................: 
1.7.16 Operator access with a tool..................................: There are not any operator
accessible areas with a tool
defined.
N
1.7.17 Equipment for restricted access locations............: dto N
2 PROTECTION FROM HAZARDS P
2.1 Protection from electric shock and energy hazards P
2.1.1 Protection in operator access areas P
2.1.1.1 Access to energized parts See below. 

<12005442 001>
Page 8 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
Test by inspection ................................................: No access with test finger and
test pin to any parts with only
basic insulation to ELV or
hazardous voltage.
P
Test with test finger .............................................: dto P
Test with test pin ..................................................: dto P
Test with test probe .............................................: No direct connection to TNV. N
2.1.1.2 Battery compartments ..........................................: No battery compartments
provided. N
2.1.1.3 Access to ELV wiring No ELV wiring in operator
accessible area. N
Working voltage (V); distance (mm) trough
insulation 
2.1.1.4 Access to hazardous voltage circuit wiring No hazardous voltage wiring in
operator accessible area. N
2.1.1.5 Energy hazards ...................................................: No energy hazard in operator
access area. P
2.1.1.6 Manual controls No conductive shafts of
operating knobs and handles. N
2.1.1.7 Discharge of capacitors in the primary circuit The time constant is less than
a second. P
Time-constant (s); measured voltage (V).............: (see appended table) 
2.1.2 Protection in service access areas No maintenance work in
operation mode necessary. N
2.1.3 Protection in restricted access locations The unit is not limited to be
used in restricted access
locations.
N
2.2 SELV circuits P
2.2.1 General requirements See below. P
2.2.2 Voltages under normal conditions (V) ..................: Between any conductor of the
SELV circuits 42.4V peak or
60Vd.c. are not exceeded.
P

<12005442 001>
Page 9 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
2.2.3 Voltages under fault conditions (V) ...................... : Single fault did not cause
excessive voltage in
accessible SELV circuits. The
limits of 71V peak and
120Vd.c. were not exceed.
Furthermore the SELV limits
(see 2.2.2) were not
exceeded for longer than 0.2
seconds. Results see
appended tables 2.2.
P
2.2.3.1 Separation by double or reinforced insulation
(method 1) P
2.2.3.2 Separation by earthed screen (method 2) P
2.2.3.3 Protection by earthing of the SELV circuit
(method 3) N
2.2.4 Connection of SELV circuits to other circuits .......: See 1.5.7, 2.2.2 and 2.2.3. P
2.3 TNV circuits No direct TNV connection. N
2.3.1 Limits N
Type of TNV circuits.............................................: 
2.3.2 Separation from other circuits and from
accessible parts N
Used insulation.....................................................: 
2.3.3 Separation from hazardous voltages N
Used insulation.....................................................: 
2.3.4 Connection of TNV circuits to other circuits N
Used insulation.....................................................: 
2.3.5 Test for operating voltages generated externally N
2.4 Limited current circuits P
2.4.1 General requirements Considered. P
2.4.2 Limit values See below P
Frequency (Hz).....................................................: See below. 
Measured current (mA) ........................................: The peak drop voltage was
measured with an oscilloscope
at a 2k:non-inductive
resistor. Results see
appended table 2.4.2.


<12005442 001>
Page 10 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
Measured voltage (V)...........................................:
<15k 
Measured capacitance (PF).................................. :
<45µC 
2.4.3 Connection of limited current circuits to other
circuits Complies. P
2.5 Limited power sources N
Inherently limited output N
Impedance limited output N
Overcurrent protective device limited output N
Regulating network limited output under normal
operating and single fault condition N
Regulating network limited output under normal
operating conditions and overcurrent protective
device limited output under single fault condition
N
Output voltage (V), output current (A), apparent
power (VA) ........................................................... :

Current rating of overcurrent protective device (A) 
2.6 Provisions for earthing and bonding P
2.6.1 Protective earthing Reliable connection of the
metal chasis to the PE
terminal (appliance inlet) via
a green/yellow insulated wire.
P
2.6.2 Functional earthing N
2.6.3 Protective earthing and protective bonding
conductors See below. P
2.6.3.1 Size of protective earthing conductors No power cord provided. N
Rated current (A), cross-sectional area (mm2),
AWG..................................................................... :

2.6.3.2 Size of protective bonding conductors See 2.6.3.3. N
Rated current (A), cross-sectional area (mm2),
AWG..................................................................... :

2.6.3.3 Rated current (A), type and nominal thread
diameter (mm) ...................................................... :
N
Resistance (:) of earthing conductors and their
terminations, test current (A) ................................ :
See appended table 2.6.3.3. P
2.6.3.4 Colour of insulation............................................... : Green/yellow wire used. P

<12005442 001>
Page 11 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
2.6.4 Terminals See below. P
2.6.4.1 Protective earthing and bonding terminals Appliance inlet used. N
Rated current (A), type and nominal thread
diameter (mm) ...................................................... :
Not permanently connected
equipment.

2.6.4.2 Separation of the protective earthing conductor
from protective bonding conductors Appliance inlet provided. Only one protective bonding
conductor provided.
N
2.6.5 Integrity of protective earthing See below. P
2.6.5.1 Interconnection of equipment This unit has it's own earthing
connection. Any other units
connected via the output shall
be provided SELV only. The
equipment does not comprise
class I and class II.
P
2.6.5.2 Components in protective earthing conductors
and protective bonding conductors No switch or overcurrent protective device in protective
earthing or bonding conductor.
P
2.6.5.3 Disconnection of protective earth Appliance inlet provided. P
2.6.5.4 Parts that can be removed by an operator Plug or inlet, the earth
connection is made before and
broken after the hazardous
voltage. No other operator
removable parts.
P
2.6.5.5 Parts removed during servicing It is not necessary to
disconnect the earth
connection except for the
removing of the earthed part
itself.
P
2.6.5.6 Corrosion resistance All safety earthing connections
in compliance with Annex J. P
2.6.5.7 Screws for protective bonding No self-tapping screws are
used. For the earth
connection to the metal
chassis a washer and a screw
are used.
P
2.6.5.8 Reliance on telecommunication network No TNV. N
2.7 Overcurrent and earth fault protection in primary circuits P

<12005442 001>
Page 12 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
2.7.1 Basic requirements The equipment relies on a 16A
rated fuse or circuit breaker of
the wall outlet protection of the
building installation in regard to
L to N short-circuits. Over
current protection is provided
by the built-in fuse.
P
2.7.2 Faults not covered in 5.3 The protection device is well
dimensioned and mounted. P
2.7.3 Short-circuit backup protection Pluggable equipment type A.
The building installation is
considered as providing short-
circuit backup protection.
P
2.7.4 Number and location of protective devices..........: Over current protection by one
built-in fuse. Protection
devices in the building
installation will provide
sufficient protection against
earth faults.
P
2.7.5 Protection by several devices Only one fuse provided. N
2.7.6 Warning to service personnel............................... : No service work necessary. N
2.8 Safety interlocks N
2.8.1 General principles N
2.8.2 Protection requirements N
2.8.3 Inadvertent reactivation N
2.8.4 Fail-safe operation N
2.8.5 Interlocks with moving parts N
2.8.6 Overriding an interlock N
2.8.7 Switches and relays in interlock systems N
2.8.7.1 Contact gaps (mm) .............................................. : N
2.8.7.2 Overload test N
2.8.7.3 Endurance test N
2.8.7.4 Electric strength test (V) N
2.8.8 Mechanical actuators N
2.9 Electrical insulation P

<12005442 001>
Page 13 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
2.9.1 Properties of insulating materials Natural rubber, asbestos or
hygroscopic materials are not
used.
P
2.9.2 Humidity conditioning 40 °C, 93% R.H. for 120 h
(tropical conditions). P
2.9.3 Requirements for insulation Insulation materials comply
with sub-clauses 2.10, 4.5.1
and 5.2.
P
2.9.4 Insulation parameters Both parameters were
considered. P
2.9.5 Categories of insulation Adequate levels of safety
insulation are provided and
maintained to comply with the
requirements of this standard.
P
2.10 Clearances, creepage distances and distances through insulation P
2.10.1 General See 2.10.3, 2.10.4, 2.10.5. P
2.10.2 Determination of working voltage The unit was connected to a
240V TN power system,
2.10.10 not applied for
P
2.10.3 Clearances See below, Annex G was not
considered. P
2.10.3.1 General Annex F and minimum
clearances considered. P
2.10.3.2 Clearances in primary circuit (See appended table 2.10.3
and 2.10.4) P
2.10.3.3 Clearances in secondary circuits In compliance with 5.3.4. N
2.10.3.4 Measurement of transient levels Normal transient voltage
considered (overvoltage
category II for primary circuit).
N
2.10.4 Creepage distances (See appended table 2.10.3
and 2.10.4) P
CTI tests ............................................................... : CTI rating for all materials of
min. 100.

2.10.5 Solid insulation See below. P
2.10.5.1 Minimum distance through insulation Optical Isolators provide
distance through insulation of
0.4 mm minimum. Details see
appended table.
P

<12005442 001>
Page 14 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
2.10.5.2 Thin sheet material The thin sheet materials of
polyester tape used in
transformer T801.
P
Number of layers (pcs)......................................... :
3 layers. 
Electric strength test 3000Vac applied on any
combination of two layers.

2.10.5.3 Printed boards ...................................................... : N
2.10.5.4 Wound components ............................................. : N
2.10.6 Coated printed boards N
2.10.6.1 General N
2.10.6.2 Sample preparation and preliminary inspection ..: N
2.10.6.3 Thermal cycling .................................................... : N
2.10.6.4 Thermal ageing .................................................... : N
2.10.6.5 Electric strength test N
2.10.6.6 Abrasion resistance test....................................... : N
Electric strength test N
2.10.7 Enclosed and sealed parts ................................... : No hermetically sealed
component. N
2.10.8 Spacings filled by insulating compound................ : Certified source of optical
isolator is used. No other
components applied for.
P
Electric strength test dto P
2.10.9 Component external terminations See appended table 2.10.2
and 2.10.3. P
2.10.10 Insulation with varying dimensions No reduction of distances
considered. N
3 WIRING, CONNECTIONS AND SUPPLY P
3.1 General P

<12005442 001>
Page 15 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
3.1.1 Current rating and overcurrent protection All internal wires are UL
recognized wiring which is
PVC insulated, rated VW-1,
300V, min. 80°C. Internal
wiring gauge is suitable for
current intended to be carried.
No internal wire for primary
power distribution.
P
3.1.2 Protection against mechanical damage Wires do not touch sharp
edges and heatsinks which
could damage the insulation
and cause hazard.
P
3.1.3 Securing of internal wiring The wires are secured by
soldering. Additionally solder-
pins, hooking-in or heat
shrinkable tubing were
provided so that a loosening
of the terminal connection is
unlikely.
P
3.1.4 Insulation of conductors The insulation of the individual
conductors is suitable for the
application and the working
voltage. For the insulation
materials see sub-clause
3.1.1.
P
3.1.5 Beads and ceramic insulators Not used. N
3.1.6 Screws for electrical contact pressure Not used. N
3.1.7 Non-metallic materials in electrical connections All connections are metal to
metal. N
3.1.8 Self-tapping and spaced thread screws No self-tapping screws are
used. P
3.1.9 Termination of conductors All conductors are reliably
secured by use of solder-pins
or glue or other mechanical
fixing means.
P
3.1.10 Sleeving on wiring Only heat shrinkable sleeving
is used. P
3.2 Connection to a.c. mains supplies P
3.2.1 Means of connection Appliance inlet. P
3.2.2 Multiple supply connections N
3.2.3 Permanently connected equipment The unit is not permanently
connected equipment. N

<12005442 001>
Page 16 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
0WODGTQHEQPFWEVQTUFKCOGVGTOOQHECDNG
CPFEQPFWKVU 

dto 
3.2.4 Appliance inlets The appliance inlet complies
with IEC/EN 60320. The
power cord can be inserted
without difficulties and does
not support the unit.
P
3.2.5 Power supply cords N
Type...................................................................... : 
Rated current (A), cross-sectional area (mm2),
AWG..................................................................... :

3.2.6 Cord anchorages and strain relief N
Mass of equipment (kg), pull (N) ........................ : 
Longitudinal displacement (mm) ......................... : 
3.2.7 Protection against mechanical damage No parts under this unit likely
to damage the power supply
cord. Enclosure without sharp
edges.
P
3.2.8 Cord guards No cord guard provided. N
D (mm); test mass (g) ......................................... : 
Radius of curvature of cord (mm)......................... : 
3.2.9 Supply wiring space Appliance inlet provided. N
3.3 Wiring terminals for connection of external conductors N
3.3.1 Wiring terminals N
3.3.2 Connection of non-detachable power supply cords N
3.3.3 Screw terminals N
3.3.4 Rated current (A), cord/cable type, cross-
sectional area (mm2) ............................................ :
N
3.3.5 Rated current (A), type and nominal thread
diameter (mm)...................................................... :
N
3.3.6 Wiring terminals design N
3.3.7 Grouping of wiring terminals N
3.3.8 Stranded wire N
3.4 Disconnection from the a.c. mains supply P

<12005442 001>
Page 17 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
3.4.1 General requirement Disconnect device provided. P
3.4.2 Disconnect devices Appliance inlet. P
3.4.3 Permanently connected equipment Not permanently connected
equipment. N
3.4.4 Parts which remain energized When the power cord is
removed from the inlet (or wall
socket) no remaining parts
with hazardous voltage in the
equipment.
P
3.4.5 Switches in flexible cords N
3.4.6 Single-phase equipment The power cord plug or inlet
disconnects both poles
simultaneously.
P
3.4.7 Three-phase equipment Single-phase equipment. N
3.4.8 Switches as disconnect devices N
3.4.9 Plugs as disconnect devices N
3.4.10 Interconnected equipment Interconnection of the power
supply to the other PCBs in
the equipment by secondary
output cable only.
N
3.4.11 Multiple power sources Only one supply connection
provided. N
3.5 Interconnection of equipment P
3.5.1 General requirements See below. P
3.5.2 Types of interconnection circuits..........................: Interconnection circuits of
SELV through sec o/p cable.
No ELV interconnection
circuits.
P
3.5.3 ELV circuits as interconnection circuits No ELV interconnection. N
4 PHYSICAL REQUIREMENTS P
4.1 Stability P
Angle of 10qThe equipment does not
overbalance when tilted to 10
degrees.
P
Test: force (N) ......................................................: N

<12005442 001>
Page 18 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
4.2 Mechanical strength P
4.2.1 General See below. After the tests, the
equipment complies with the
requirements of sub-clauses
2.1.1, 2.6.1, 2.10 and 4.4.1.
P
4.2.2 Steady force test, 10 N 10N applied to all components
other than enclosure. P
4.2.3 Steady force test, 30 N Applied to the internal metal
enclosures. P
4.2.4 Steady force test, 250 N 250N applied to outer
enclosure. No energy or other
hazards.
P
4.2.5 Impact test No hazard as result from steel
ball impact test. P
4.2.6 Drop test Not required for movable
equipment. N
4.2.7 Stress relief After the test of A.10 no
shrinkage, distortion or
loosening of any enclosure
part was noticeable on the
equipment.
P
4.2.8 Cathode ray tubes No CRT used. 
Picture tube separately certified ........................... :
N
Picture tubes > 16 cm intrinsically protected N
Non-intrinsically protected tubes > 16 cm used
with protective screen N
Intrinsically protected tubes: tests on 12 samples N
Samples subject to ageing: 6 N
Samples subject to implosion test: 6 N
Samples subject to mechanical strength test
(steel ball): 6 N
Non-intrinsically protected tubes tested N
4.2.9 High pressure lamps No high-pressure lamps
provided. N
4.2.10 Wall or ceiling mounted equipment; force (N) ....: N
4.3 Design and construction P
4.3.1 Edges and corners Edges and corners of the
enclosure are rounded. P

<12005442 001>
Page 19 of 78
IEC 60950
Clause Requirement Test Result – Remark Verdict
TRF No.: I950___E TRF originator: FIMKO
4.3.2 *CPFNGUCPFOCPWCNEQPVTQNUHQTEG0  

No handles or controls
provided. N
4.3.3 Adjustable controls No controls provided. N
4.3.4 Securing of parts Mechanical fixings in such a
way designed that they will
withstand mechanical stress
occurring in normal use.
P
4.3.5 Connection of plugs and sockets No mismating of connectors,
plugs or sockets possible. P
4.3.6 Direct plug-in equipment Not direct plug-in type. N
Torque (Nm)......................................................... : dto 
4.3.7 Heating elements in earthed equipment No heating elements
provided. N
4.3.8 Batteries No batteries provided. N
4.3.9 Oil and grease Insulation in intended use not
considered to be exposed to
oil or grease.
P
4.3.10 Dust, powders, liquids and gases The equipment in intended
use not considered to be
exposed to dust, powders,
liquids and gases.
P
4.3.11 Containers for liquids or gases No container for liquid or gas
provided. N
4.3.12 Flammable liquids ................................................ : No flammable liquids
provided. N
Quantity of liquid (l) .............................................. : N
Flash point (qC) .................................................... : N
4.3.13 Radiation; type of radiation .................................. : No radiation. AEL of control
LED far below the limiting
values for LED Class 1.
P
Equipment using lasers, see separate test report
of IEC 60825-1. N
4.4 Protection against hazardous moving parts N
4.4.1 General N
4.4.2 Protection in operator access areas N
4.4.3 Protection in restricted access locations N
4.4.4 Protection in service access areas N