AGA Six Four Series User manual

AGA
AGA Six Four Series Six Four Series
(with ceramic hob)
(with ceramic hob)
assembly instructions for models supplied modular
s.t 6.05
sixfourassbly2
Specification
Total fully assembled weight --- 218kg
Power Supply --- 230V 50Hz Single or 3 Phase
Maximum electrical load --- 16.9 kW
Hotplate
Front left --- 0.75 - 2.2 kW
Rear left --- 1.2 kW
Front centre --- 1.2 kW
Rear centre --- 0.75 - 2.2 kW
Front right --- 1.5 kW
Rear right --- 1.5 kW
Ovens
Conventional Oven --- 2.0 kW
Fan Oven --- 2.0 kW
Simmering Oven --- 0.9 kW
Grill --- 2.2 kW

AGA
AGA Six Four series (Ceramic Hob) Six Four series (Ceramic Hob)
---
--- assembly instructions for modular models
assembly instructions for modular models
Installation Requirements
Floor :-
To ease handling the product may be delivered in five separate cartons, the heaviest
of which is 86kg. This requires the cooker to be assembled on site in accordance with
these instructions.
The floor should be level and strong enough to carry the total weight of 218kg. There
are levelling adjustments fitted to the Aga to compensate for minor variations.
This product does not require a safety chain or stability bracket
Clearances:-
Refer to diagram overleaf
Where the Aga is to be ‘slot’ fitted, a gap of 3mm is recommended each side, to allow
the product to slide in easy. See dimension ’B’
Dimension ‘A’ 60mm, is the clearance to be provided against any side wall which
extends above the level of the hob, to allow for protruding utensil handles.
Dimension ‘C’ 650mm is the minimum clearance required to any surface immediately
above the hob. but, if a cooker hood is to be installed, the clearance must be increased
to 800mm. We recommend the Aga CH900 hood which has been specifically designed
for this product.
Electrical Supply:-
The Six-Four requires connection to a single phase 45 amp supply, using a 10mm2
cable.
Alternatively, a 3 phase & neutral supply may be used with 2.5mm2 cable, noting that in
this case the load is as follows L1 5.0 kW, L2 4.65 kW, L3 7.3 kW
Conversion between 1 phase /3 phase is easily accompished as shown overleaf
An appropriate electrical isolator must be fitted within 2 metres of the Aga, but not sited
immediately above it. In the case of an existing supply, it should be confirmed that both
the isolator and the cable back to the distribution board are both rated to deliver 45 amp
An excess length/loop of cable should be provided at the rear to permit connection into
the Aga, into the position shown overleaf.
Cable entry is at the Right-hand side of the rear panel at high level.
2

AGA
AGA Six Four series (Ceramic Hob) Six Four series (Ceramic Hob)
---
--- assembly instructions for modular models
assembly instructions for modular models 3

Cable entry position
1 phase connections
3 phase connections (live links removed)
Assembly procedure:-
1. Check that
all 5 cartons
are present and
carefully
unpack the
contents.
Remove side
panels from
oven assembly,
but leave rear
panel in place
to provide lifting
point.
Lift oven assembly off of its pallet.
AGA
AGA Six Four series (Ceramic Hob) Six Four series (Ceramic Hob)
---
--- assembly instructions for modular models
assembly instructions for modular models 4

Remove rear panel (7 screws) From the rear of the Front plate. Remove
four outer screws but leave the two centre
ones loosely in place.
Lift front-plate onto chassis, engaging the two centre screws into the slotted holes.
Ensure that the front-plate drops down ino the baseplate and that the apertures line up
to the ovens. The seals should be slightly compressed.
Using an extended length screwdriver passing
between the ovens, tighten the centre two screws,
then evenly around the outer ones, ensuring that
the ovens seal against front-plate.
AGA
AGA Six Four series (Ceramic Hob) Six Four series (Ceramic Hob)
---
--- assembly instructions for modular models
assembly instructions for modular models 5

Identify and unwrap
the three oven ther-
mostat capillarys.
These will be found
labelled and tied to
the rear of the hot-
plate chassis.
To avoid confusion,
work with one at a
time.
Fasten the hotplate chassis down to the the main assembly. 4 screws.
Lower left
Thread each capillary through into its respective oven and into its retaining clip.
Lower left
Lower rightLower right
AGA
AGA Six Four series (Ceramic Hob) Six Four series (Ceramic Hob)
---
--- assembly instructions for modular models
assembly instructions for modular models 6

Plug in the two multi-way plugs. They are
biased and will only fit into their correct
sockets.
Refit rear panel.
An electrical safety test must now be
performed.
Confirm that the household electrical
supply is of correct polarity.
Select 500v on a megger tester and
connect the leads on to the appliance
connections.
Depress the test button and record
results.Meter should read infinity.
Any inconclusive results should be
investigated and rectified.
Top right
Top right
Bring in and terminate incoming mains cable. For 3 phase supples, remove the live
links L1-L2 & L2-L3, as shown in diagram on page 4
AGA
AGA Six Four series (Ceramic Hob) Six Four series (Ceramic Hob)
---
--- assembly instructions for modular models
assembly instructions for modular models 7

Refit side panels. Note that they drop down into the base then slide forward into posi-
tion.
Slot splashback into its sockets
Cooker may now be rolled into its final position.
Using the four levelling screws, turn clockwise to raise the cooker off of its wheels
and to obtain the final level adjustment.
Lift the ceramic
top-plate into
position (minus
the clock
assembly) and
secure with the
four corner
stay-nuts and
buttons.
AGA
AGA Six Four series (Ceramic Hob) Six Four series (Ceramic Hob)
---
--- assembly instructions for modular models
assembly instructions for modular models 8

Remove the bracket from the back of the
time clock (2 screws)
Connect the multi-way plug.
Push the clock assembly into the fascia,
engaging the tongue as shown.
Refit the fixing
bracket from
underneath
Complete installation by fitting the doors and testing the correct functions of ovens and
hotplate etc.
Push-fit the neons into their respective posi-
tions on the front fascia.
AGA
AGA Six Four series (Ceramic Hob) Six Four series (Ceramic Hob)
---
--- assembly instructions for modular models
assembly instructions for modular models 9