AGILE A-5 User manual

Length：1065mm
Height：330mm
Width：182mm
Main Rotor Diameter：Ø1250
Main Blade Length：550mm
Tail Rotor Diameter：Ø260mm
Tail Blade Length：92mm
Motor Pinion：21T
Motor KV：1200KV
Driving Gear：(21/54)(17/56)
Gear Ratio：21T(8.89:1)
Tail Gear Ratio: 3.86:1
Weight(w/o power)：2500g(Incl canopy/ main blade/ tail blade)
Flying Weight: 3200g
Battery：22.2V 4500-5500mAh
ESC：120A
Version No：20191116
使用说明书使用说明书
Thank you for buying Agile products. Please read this
manual carefully before assembling. We recommend that
you keep this manual for future reference regarding tuning
and maintenance.
感谢您选购 KDS AGILE产品， 请您详细的阅读完这
本说明书之后再进行组装以及操作这台直升机，同时
请您妥善的保存这本说明书，作为日后进行调整以及
维修与参考。
机身长度：1065mm
机身高度：330mm
机身宽度：182mm
主旋翼直径：Ø1250
主旋翼长度：550mm
尾旋翼直径：Ø260mm
尾旋翼长度：92mm
马达齿：21T
马达KV ：1200KV
传动齿轮：(21/54)(17/56)
传动比：21T(8.89:1)
尾传动比：3.86:1
空机重量：2500g(含头罩/主桨/尾桨)
起飞重量：3200g
电池：22.2V 4500-5500MAH
电调：120A
INSTRUCTION MANUAL
INSTRUCTION MANUAL

Congratulations on your purchase of the Agile A-5 radio controlled helicopter kit. Agile A-5 was designed in Europe by
Eng. Gaziano Roberto and is proudly manufactured by KDS Model. Our goal was to offer you something different with a
minimum of parts, easy maintenance, and outstanding flying performances.
It’s time to fly different!...
IMPORTANT NOT ES
NOTE FOR ASSEMBLY
R/C helicopters, including the AGILE A-5 are not toys. R/C helicopters utilize various high-tech products and
technologies to provide superior performance. Improper use of this product can result in serious injury or even death.
Please read this manual carefully before using and make sure to be conscious of your own personal safety and the
safety of others and your environment when operating all AGILE products. Agile A-5, KDS Model, their affiliates and
authorized distributors are not responsible for personal injuries to the operators and others, and property damages that
could occur from the assembly, maintenance or your use/misuse of this product. Always respect the rules provided by
your local remote control aircraft organization.
The following manual provide important instructions to correctly assemble the model. It is structured in a logical way, based on
the work done in previous step. If you change the order, it may result in additional or unnecessary steps. So we suggest you to
read this user manual very carefully to understand correctly the assembly procedure. Failure to do so may not only downgrade
performances but also increase the risk of danger. Apply thread lock as indicated, allow the threadlock to cure before mounting
parts. It is recommended to use threadlock on each bolt or screw that are engaged with metal parts.
LOCATE AN APPROPRIATE LO CATION
R/C helicopters fly at high speed, thus posing a certain degree of potential danger. Choose an
appropriate flying site consisting of flat, smooth ground, a clear open field, or a large open
room, such as gymnasium or warehouse without obstacles. Do not fly near buildings, high
voltage cables, or trees to ensure the safety of yourself, others and your model. Do not play
your model in inclement weather, such as rain, wind, snow or darkness.
OB TAIN THE ASS ISTANCE OF A N EXPERIENCED PILOT
Before turning on your model and transmitter, check to make sure no one else is operating on
the same frequency. Frequency interference can cause your model, or other models to crash.
The guidance provided by an experienced pilot will be invaluable for the assembly, tuning,
trimming, and actual first flight(recommend you to practice with computer-based flight
simulator).
1.INTRODUCTION
2.SAFETY NOTES
During the operation of the helicopter, the main rotor will be spinning at a high rate of speed.
The blades are capable of inflicting serious bodily injury and damage the environment. Be
conscious of your actions, and careful to keep your face, eyes, hands, and loose clothing
away from the blades. Always fly the model a safe distance from yourself and others, as well
as surrounding objects. Never take your eyes off the model or leave it unattended while it is
turned on. lmmediately turn off the model and transmitter when you have landed the model.
ALWAYS BE AWARE O F THE ROTATING BLADE S
Enjoy the built and have a great time with you Agile A-5 !
Page 01
Agile 系列直升机商标为欧洲Flight Research RC 所持有,由深圳KDS模型荣誉生产。

Page 02
恭 喜 你 购 买 AGILE A-5 无线电遥控直升机，AGILE A-5 是来自欧洲的设计师ENG.Gaziano Roberto 设 计 ， 由
KDS 模 型 生 产制造 完 成 。我们 的 目标是 用 最 少的配 件 ， 为客户 提 供 高质量 产 品，容 易 维 护以及 达 到 出色的 飞 行
KDS AGILE A-5 遥控直升机并非玩具， 它是结合了许多高科技产品所设计出来的休闲用品，所以商品的使用不
当或不熟悉都可能会造成严重伤害甚至死亡，使用之前请务必详读使用说明书，勿轻忽并注意自身安全， 任何
遥 控 直 升 机 的 使 用 ， 制 造 商 和 经 销 商 是 无 法 对 使 用 者 于 零 件 使 用 的 损 耗 异 常 或 组 装 不 当 所 发 生 之 意 外 负 任 何 责
任 ， 本 产 品 是 提 供 有 操 作 过 模 型 直 升 机 经 验 的 成 人 或 者 有 相 当 技 术 的 人 员 在 旁 指 导 ， 以 确 保 安 全 无 虞 下 操 作 使
用， 产 品 售出后本 公 司 将不负任 何 操 作和使 用 控 制上的任 何 性 能与安全 责 任 。KDS公司, 附属 子 公 司和授 权 分 销
商不承担任何的个人伤害以及其他， 永远遵守当地为遥控模 型飞机提供的规范。
远离障碍物及人群
避免独自操控
远离运转中零件
重要声明：
Agile 系列直升机商标为欧洲Flight Research RC 所持有,由深圳KDS模型荣誉生产。
直升机飞行时具有一定的速度，相对的也潜在一定危险性，场地的选择也相对的重
要，请遵守法规到合适遥控飞行场地飞行。必须注意周围有没有人，高楼，建筑物，
高压 电 线 ，树木等 等 ， 避免操 控 的 不当造成 自 己 与他人财 产 的 损坏。 初 次 练习时， 务
必选择在空旷合法专属飞行场地并适当搭配练习架飞行，这对飞行失误造成的损伤将
会大幅的降低。 请勿在下雨，打雷等恶 劣天气下操作，以确保 本身及机体的安全。
至飞行场飞行前，需确认是否有相同频率的同行正进行飞行，因为开启相同频率的发射机将导
致自己与他人立即干扰等意外危险。遥控飞行操控技巧在学习初期有一定的难度，要尽量避免
独自操作飞行，需有经验的人士在旁指导，才可以操控飞行。（勤练模拟器及老手指导是入门
必要的选择）。
当直升机主旋翼与尾旋翼运转时，切勿触摸并远离任何物件，以避免造成危险与损坏。
享受您的Agile A-5 直升机并玩得愉快!
2.安全注意事项
1.简介

PROPER O PERATION
Please use the replacement of parts on the manual to ensure the safety of instructors. This
product is for R/C model, so do not use for other purpose.
SA FE OPERATI ON
Operate this unit within your ability. Do not fly under tired condition or improper operation,
which may cause danger.
3.Safety Check Before Flying
Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 03
Before flying, for safety reasons, make sure that no one else is operating a R/C model on the same frequency as yours.
Before flying, please check that the power of your transmitter and your helicopter are sufficient for the flight.
Before turning on the transmitter, please check that the throttle stick is in its lowest position, IDLE UP switch must be on
OFF position.
When turning off the model, please follow the power on/off procedure. Power ON: turn on the transmitter first, then turn on
helicopter power. Power OFF: turn off the helicopter power first and then turn off the transmitter. Improper operating
procedure
may cause the model to be out of control, so please do make this your habit.
Before operation, check that every movement is smooth and directions are correct. Inspect servos carefully for
interferences and broken gears.
Check for missing or loose screws and nuts. See if there is any cracked and/or incomplete assembly of parts.
Check main rotor blades and rotor holders carefully. Broken and premature failures of parts might result in a dangerous
situation or crash.
Check all ball links to avoid excess play and replace as needed. Failure to do so will result in poor flight stability.
Check that the battery and power plugs are fastened. Vibrations and violent flight might loosen the plugs and so lead to
out of control.
Check for the tension of main drive belt.
PR EVENT MOISTURE
R/C models are composed of many precision electrical components. lt is critical to keep the
model and associated equipment away from moisture and other contaminants. The
introduction or exposure to water or moisture in any form can cause the model to malfunction
resulting in loss of use, or a crash. Do not operate or expose to rain or moisture.
KE EP AWAY FRO M HEAT
R/C models are made up of various forms of plastic. Plastic is very susceptible to damage or
deformation due to extreme heat and cold climate. Make sure not to store the model near any
source of heat such as an oven, or heater. lt is best to store the model indoors, in a climate-
controlled, room temperature environment.
4.Tools Required
-Hex drivers : 1.5, 2, 2.5, 3, 4mm
-Nut Drivers : 5.5, 7mm
-Ball link pliers
-Diagonal cutting pliers
-Scissors
-Metric ruler
-Soldering iron + solder (for motor and ESC wiring)
-Pitch gauge (for set up)
-Swashplate leveller
-Threadlock blue * (medium)
-Threadlock red * (high strength)
-Bearing retainer compound
-Epoxy A+B Glue
-Grease
-Oil
*Colors may vary depending on your area.

3.飞行前安全检查重要事项
Page 04
每次飞行前应先确认所使用的频率是 否会干扰他人，已确保 你自身与他人的安全。
每次飞行前确定你发射机与直升机电 池的电量是否足够飞行 的状态。
开机前确认油门摇杆是否位于最低点，熄火降落开关，定速开关（IDLE）是否于关闭状态。
关机时必须遵守电源开关机程序，开机时应先开启发射机后，再开启直升机电源，关机时应先关闭直升机电
源 ， 再 关 闭 发 射 机 电 源 ， 不 正 确 的 开 关 机 程 序 会 造 成 失 控 现 象 ， 影 响 自 身 与 他 人 的 安 全 ， 请 养 成 正 确 的 习
惯。
开机请先确定直升机的各个动作是否顺畅，及方向是否正确，并检查伺服的动作是否有干涩或崩齿的情形，
使用故障的伺服将会导致不可预期的 危险。
飞行前确认没有缺少或者松眼的螺丝与螺帽，确认没有组装不完整或损毁的零件，仔细检查主旋翼是否有损
坏，特别是接近主旋翼夹座的部位。
损坏或组装不完整的零件不仅影响飞 行，更会造成不可预期 的危险。
注意：对损坏，有裂痕零件更新及定期保养检查的要性，检查所有的连杆头是否有松脱的情形，过松的连杆
头应先更新，否则将造成直升机无法 操控的危险。
确认电池及电源接头是否固定牢靠，以及主传动皮带的拉力，飞行中的震动或激烈的飞行，可以造成接头松
脱/皮带磨损及失控的危险。
4.自行必备的工具
• 对边六角螺丝刀：1.5 ，2， 2.5, 3，4 MM
• 六角套筒：5.5，7 MM
• 球头钳
• 斜口钳
• 剪刀
• 直尺
• 焊铁+焊锡（焊马达+电调转接头）
• 螺距规
• 十字盘水平仪
• 蓝色螺丝胶（中等）
• 红色轴承胶（高强度）
• 环氧树脂A+B胶
• 润滑油
勿不当使用本产品
请勿自 行改造加工 ，任何的升 级改装或维 修，请使用KDS产品目录中的零件，以确保结
构的安全，请确认于产品界限内操作，请勿过载使用，并勿用于安全，法令外其它非
法用途。
安全操作
请于自己能力内及需要一定技术范围内操作这台直升机，过于疲劳，精神不佳或不当
操作，意外风险可能会提高。
Agile 系列直升机商标为欧洲Flight Research RC 所持有,由深圳KDS模型荣誉生产。
远离潮湿环境
直升机内部也是由许多精密的电子零器件组成，所以必须绝对的防止潮湿或水气，避
免在浴室或雨天时使用，防止水气进入机身内部而导致机件及电子零件故障而引发不
可预期的意外！
远离热源
遥 控 飞 机 多 半 是 以PA维 修 或 聚 乙 烯 ， 电 子 商 品 为 主 要 材 质 ， 因 此 要 尽 量 远 离 热 源 ， 日
晒以避免因高温而变形甚至熔毁损坏 的可能。

5.Equipment Required for Assembly
RADIO TRANSMITTER AND ELECTRONIC EQUIPMENT REQUIRED FOR ASSEMBLY
•Brushless electric motor: 6s Lipo - 1200KV
(4mm Bolt holes, 30mm mount width, 6mm * 37mm motor shaft)
•Speed controller: minimum 120A
(ESC specs limits should be rated accordingly to the maximum amps handling by the motor)
•Lipo Batteries: 6s 5000-5500 mAh
•Electronic flybarless system
•3 pcs Metal standard servo's / 3 pcs Metal medium sized servo's
•1 tail rotor servo, standard size, high speed required
•550 mm main rotor blades
•92 mm tail rotor blades(included)
•6 channel or more helicopter transmitter system, 2.4 Ghz frequency preferred
•Receiver 6 channel or more (working with your transmitter specs)
“A” Glue width: approx. 2mm
2mm
“OIL” Lubrication grease. “A” thread lock, apply a small amount on screws or metal parts and wipe surplus off. When
disassembling, recommend to heat the metal joint about 15 seconds. (NOTE: Keep plastic parts away from heat.)
When you see the marks as below, please use glue or grease to ensure flying safety.
Page 05
Agile 系列直升机商标为欧洲Flight Research RC 所持有,由深圳KDS模型荣誉生产。
6.Specification
1065mm
330mm
182mm

5.飞机所需的配置
发射机和电子配件
• 无刷马达：6S LIPO-1200KV（4mm 螺丝孔，30mm安装宽度，6mm马达轴）
• 电子调速器：最低120A
• 锂电池：6S 5000-5500mAh
• 3个金属标准舵机或3个金属中型舵机
• 1个金属尾舵
• 550mm 主旋翼碳纤桨叶
• 92mm 尾旋 翼碳纤桨叶
• 6通以上，2.4G 遥控器
• 6通以上接收机与发射机匹配
“A“胶水 宽度：大约- 2MM
2mm
“ 油 “润滑油。 ”A“ 螺丝胶应用少量涂敷于螺丝以及金属配件，多涂的应擦拭干净，拆卸时，建议先
加热金属连接部分15秒。
当你看到如下标记,请使用胶水或润滑脂,以确保飞行安全。
A+B胶 中性粘度 螺丝胶 中性粘 度螺丝胶 高强度螺 丝胶 润滑油
Page 06
6.规格说明
Agile 系列直升机商标为欧洲Flight Research RC 所持有,由深圳KDS模型荣誉生产。
1065mm
330mm
182mm

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 07
7.组装说明 ASSEMBLY SECTION
轴承
Bearing
φ9Xφ20X5
主轴轴承 下座
Servos under mount
轴承
Bearing
φ10Xφ19X5
B
B
沉头内六角螺丝
Countersunk head socket screw
M2.5*6
机身连接 板
CF Frame connection plate
Battery tray fixed column
电池板固 定柱子 侧板连 接柱
Frame connecting bolt
侧板连接 柱
Frame connecting bolt
沉头内六角螺丝
Countersunk head socket screw
M2.5*6
机身连接 板
CF Frame
connection plate
杯头内六 角螺丝
Hexagon socket head
cap screws
M3X22
轴承
Bearing
φ3Xφ7X3
垫片
Washer
3X5X0.5
皮带压轮
Belt wheel
皮带压固 定座
Belt wheel mount
皮带压固定座（有螺牙）
Belt wheel mount (with threaded)

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 08
7.组装说明 ASSEMBLY SECTION
侧板
Main frame
电池板滑 轨
Battery plate slippery course
脚架固定 座
Landing gear mount
机壳支柱
Canopy support
螺丝垫片
Screw gasket
杯头内六角螺丝
Hexagon socket head cap screws
M3X8
半圆头内 六角螺丝
Hexagon socket screws
M2X5
半圆头内 六角螺丝
Hexagon socket screws
M3X6
杯头内六角螺丝
Hexagon socket head
cap screws
M3X8
半圆头内 六角螺丝
Hexagon socket screws
M3X6

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 09
7.组装说明 ASSEMBLY SECTION
螺丝垫片
Screw gasket
杯头内六 角螺丝
Hexagon socket head cap screws
M3X8
电池板滑 轨
Battery plate
slippery course
半圆头内 六角螺丝
Hexagon socket screws
M2X5
机壳支柱
Canopy standoff
半圆头内 六角螺丝
Hexagon socket screws
M3X6
半圆头内 六角螺丝
Hexagon socket screws
M3X6
杯头内六 角螺丝
Hexagon socket head
cap screws
M3X8
杯头内六 角螺丝
Hexagon socket head
cap screws
M3X8
电子放置 板
CF electronic plate
侧板
Main frame
After the Main frame set is assembled,
the side panels need to be 90 degrees vertical
机身组装好后 两侧板须水平面 垂直成 90度

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 10
7.组装说明 ASSEMBLY SECTION
主轴轴承 上座
Main shaft under mount
十字盘导 轨
Swashplate Anti-rotation bracket
轴承
Bearing
φ10Xφ19X5
杯头内六角螺丝
Hexagon socket
head cap screws
M2.5X8
标准舵机安装架
Standard servo mounting frame
轴承
Bearing
φ10Xφ19X5
标准舵机 固 定支架
Standard servo mounting frame
半圆头内 六角螺丝
Hexagon socket screws
M3X6
主舵机固 定座
Main servos mount
中型舵机 固 定支架
Medium sized servo mounting frame
半圆头内 六角螺丝
Hexagon socket screws
M3X6
杯头内六角螺丝
Hexagon socket head cap screws
M3X10
B
轴承压片
Bearing plate
半圆头内 六角螺丝
Hexagon socket screws
M2.5X6
中型舵机固定支 架
Medium sized servo mounting frame

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 11
7.组装说明 ASSEMBLY SECTION
皮带
Motor belt
杯头内六 角螺丝
Hexagon socket head
cap screws
M3X8
杯头内六 角螺丝
Hexagon socket head cap screws
M3X8
螺丝垫片
Screw gasket
杯头内六角螺丝
Hexagon socket head cap screws
M3X8
防松螺母M4
Locknut
皮带轮54T
First reduction gear
杯头内 六 角螺丝
Hexagon socket head
cap screws
M3X25
二级齿 轮 17T
Secondary gear 17T
X3
舵机
Servo
螺母M2
Nut
舵机臂
Servo arm
球头 A
Bails A 圆头螺丝
Round head screw
M3X6

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 12
7.组装说明 ASSEMBLY SECTION
标准舵机
Standard servo
杯头内六角螺丝
Hexagon socket head
cap screws
M2.5X10
舵机压片
Servo plate
舵机压片
Servo plate 杯头内六角螺丝
Hexagon socket head
cap screws
M2.5X10
中型舵机
Medium sized servo
舵机装入机架前需调舵机中位设置好
Please adjust the middle position of
the servo's before installing it

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 13
7.组装说明 ASSEMBLY SECTION
球头 A
Bails A
螺母M2
Nut
圆头螺丝
Round head screw
M3X6
舵机臂
Servo arm
舵机
Servo
舵机压片
Servo plate
杯头内六角螺丝
Hexagon socket head
cap screws
M2.5X10
螺丝垫片
Screw gasket
杯头内六角螺丝
Hexagon socket head cap screws
M3X8
杯头内六 角螺丝
Hexagon socket head
cap screws
M3X6
杯头内六 角螺丝
Hexagon socket head
cap screws
M3X8
尾舵机固 定座
Tail servo mount
升降舵机
Elevator scrvo
螺距舵机
Pitch Servo
副翼舵机
Ailcron scrvo
舵机装入机架前需调舵机中位设置好
Please adjust the middle position of
the servo's before installing it

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 14
7.组装说明 ASSEMBLY SECTION
无刷马达
Motor 马达固定座
Motor mount
杯头内六 角螺丝
Hexagon socket head cap screws
M4X8
机米螺丝
Set screw
M4X4
马达齿轮
Drive pinion 21T
杯头内六角螺丝
Hexagon socket head
cap screws
M4X8
螺丝垫片
Screw gasket
螺丝垫片
Screw gasket
杯头内六 角螺丝
Hexagon socket head
cap screws
M4X14
皮带松紧 度
#1
#2
#3
1.将#1#2螺丝 锁入相应螺 丝孔
用手沿着 主轴反方向 推动马达;
2.锁紧螺 丝#1;
3.锁紧马达螺丝#2;
4.用手转 动马达，确 保皮带与大齿平行;
5.最后检 查马达皮带 松紧，用一个手指
穿过孔推 动皮带，困 难时需调整适合松紧度;
1.Push the motor in the opposite direction of the main
shaft as far as you can(by hand).
2.Tighten slide screws #1
3.Tighten motor mount locking screws #2
4.Rotate the motor several times by hand.Ensure that
belt is correclty aligned with the big pulley
5.You can check the belt tension by hand.you just
have to push the belt with one of your finger
through the round opening on frame # 3.
It should be difficult to push motor belt

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 15
7.组装说明 ASSEMBLY SECTION
杯头内六角螺丝
Hexagon socket head
cap screws
M3X10
机米螺丝
Set screw
M3X3
脚架管
Skid set
脚架
Landing gear
半圆头内 六角螺丝
Hexagon socket screws
M3X6
尾管固 定 座
Tail boom fixed aluminum gasket
机壳支柱
Canopy support
防松螺 母 M3
Locknut
双头螺杆
Double head screw
尾管固定 铝垫
Tail boom fixed
aluminum gasket
尾管固定 座螺杆待尾管装 入后再锁紧
After the tail boom is installed, tighten
Double head screw

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 16
7.组装说明 ASSEMBLY SECTION
轴承
Bearing
φ8Xφ16X5
主桨夹
Main blade grip
止推轴承
Thrust bearing
F8-16M
轴承
Bearing
φ8Xφ16X5
垫片
Washer
φ12Xφ15.8X0.5
杯头内六角螺丝
Hexagon socket head
cap screws
M3X12
杯头内六 角螺丝
Hexagon socket head
cap screws
M3X6
大桨夹 支 臂
Main blade grip arm
杯头内六 角螺丝
Hexagon socket head
cap screws
M5X12
横轴
Spindle shafts
垫片
Washer
φ5Xφ13X1.5
横轴减 震 圈
Oring 90°
垫片
Washer
φ8Xφ12X1.0
中联
Main rotor heuseing
垫片
Washer
φ8.5Xφ13X2
球头 B
BALL B
止推轴承滚珠 涂润滑油
Thrust bearings need lubricating oil
外径大
Larger ID
外径小
Smaller ID

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 17
9.组装说明 ASSEMBLY SECTION
FBL转接臂
FBL Radius head
机米螺丝
Set screw
M2.5X10
球头扣
Bail link
轴承
Bearing
φ3Xφ6X2.5
垫片
Washer
φ3Xφ4.5X1.1
杯头内六角螺丝
Hexagon socket head
cap screws
M2.5X10
垫片
Washer
φ2.5Xφ4.5X1.1
FBL摇臂
FBL Radius arm
杯头内六角螺丝
Hexagon socket head
cap screws
M3X16
垫片
Washer
φ3Xφ5X0.5
杯头内六 角螺丝
Hexagon socket head
cap screws
M4X20
防松螺 母 M4
Locknut
法兰轴承
Flange Bearing
φ2.5Xφ6X2.6
主轴
Main shaft

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 17
9.组装说明 ASSEMBLY SECTION
圆头螺丝
Round head screw
M2X4
十字内盘 下盖
Swashplate inner plate
轴承
Bearing
φ30Xφ37X4
十字外盘
Swashplate outer plate
关节轴承
Knuckle bearing
十字内盘 上盖
Swashplate under cap
杯头内六角螺丝
Hexagon socket head cap screws
M2X8
球头 B
BALL B
球头 C
BALL C
球头 D
BALL D
球头扣
Bail link
拉杆
Linkage Rod
57mm
Have "A" sign ball link pointing out
球头扣有“A”字面朝外

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen
Page 18
轴承
Bearing
φ5Xφ10X4
尾中联
Tail rotor hub
尾桨夹
Tail blade grip
防松螺 母 M3
Locknut
垫片
Washer
7X9.8X0.5
球头 C
Bails
垫片
Washer
3X8X1.0
止推轴 承
Thrust bearing
尾推滑块 铜套
Tail picth slider copper bush
法兰轴 承
Flange Bearing
φ7Xφ11X3
尾推轴承 座
Tail picth slide bearing mount
尾推滑块U型 臂
Tail picth slider U arm
E形扣
E ring
铝套
Aluminum sleeve
球头扣
Ball lingk
销子
Pin
止推轴承滚珠 涂润滑油
Thrust bearings need lubricating oil
尾桨夹组装完成后向外拉紧,此处有约0.5m m间隙属正常现象
After the Tail blade grip is assembled, pull tight on both sides .
The clearance of about 0.5mm in this position is normal.
尾此步骤出 厂己打螺丝 胶
Screw glue has been
applied at the factory
外径大
Larger ID
外径小
Smaller ID