Agilent Technologies E8041A Interposer Operating and maintenance manual

Agilent Technologies
E8041A Interposer for the Intel® Pentium® 4
Processor in the 478-Pin Package
Interposer Installation
Quick Start

2 E8041A Interposer Quick Start
Protecting the Interposer
Here is a summary of precautions to take to avoid damaging the interposer:
DO minimize the removal of the analysis probe cables, once they are connected
to the interposer.
DO minimize the removal of the interposer, once it is connected to the
microprocessor and target system.
DO exercise patience and care when working with the interposer.
DO use ESD precautions.
DO remove power from the target system and analysis probe before making
attachments.
DO protect the pins from damage by covering them with the pin protector when
the interposer is not in use.
DO NOT insert any kind of tool between the interposer and the microprocessor,
except as described in this manual.
DO NOT kink the analysis probe cables.
DO NOT pull on or twist the "wings" of the interposer.

E8041A Interposer Quick Start 3
1Remove the heatsink from the microprocessor.
2Remove the microprocessor from the target system.
3Remove the Intel retention module from the target
system.
4Install the Agilent retention modules.

4 E8041A Interposer Quick Start
5Check that the socket on the target system is still
open.
6Remove the pin protector from the interposer.
Keep the pin protector. You will need it to prevent damage to the interposer
whenever the interposer is not plugged into the target system.

E8041A Interposer Quick Start 5
7Align the interposer over the socket on the target
system.
Note how the socket on the interposer is rotated 80° relative to the socket on
the target system. This is done so that the interposer will not interfere with
the target socket’s actuation mechanism.
The wings of the interposer will flex around the retention modules.
8Gently wiggle the interposer until you feel the pins
fall into the holes of the socket.
9Visually check that the bottom of the interposer is
flush with the top of the socket on the target
system.

6 E8041A Interposer Quick Start
10 With one hand, apply light downward pressure on
the interposer. With the other hand, close the the
socket.
11 Align the processor over the socket on the
interposer.
12 Gently wiggle the assembly until you feel the pins
fall into the holes. Visually check that the bottom of
the processor module is flush with the top of the
socket on the interposer.
CAUTION
The processor should be oriented the same way that it was originally oriented
on the target system. Note that the orientation of the processor with respect to
the lever on the socket is opposite from the target system. The socket is keyed,
so the processor will only go in the right way.

E8041A Interposer Quick Start 7
13 Apply light downward pressure on the processor
while you close the interposer socket.
14 Re-install the heatsink.

8 E8041A Interposer Quick Start
15 Install the clip assembly to hold the heatsink in
place.
Use the clip assembly which you removed earlier.

E8041A Interposer Quick Start 9
16 Connect the analysis probe cables to the interposer.
Refer to the silkscreened labels on the interposer and on the cable paddles.
Install the supplied clips to keep the paddles on the end of the analysis probe
cables from pulling apart.
17 Connect the analysis probe to the logic analyzer.
Connect the pod cables to the connectors on the analysis probe as shown on
the back of the analysis probe.

10 E8041A Interposer Quick Start

Agilent Technologies Inc.
P.O. Box 2 97
900 Garden of the Gods Road
Colorado Springs, CO 8090 -2 97, U.S.A.
© Copyright 200 Agilent
Technologies, Inc.
Agilent/Intel Confidential.
Information in this document is
subject to your nondisclosure
agreement.
No part of this manual may be
reproduced in any form or by any
means (including electronic
storage and retrieval or
translation into a foreign
language) without prior
agreement and written consent
from Agilent Technologies, Inc. as
governed by United States and
international copyright laws.
Restricted Rights Legend
Use, duplication, or disclosure
by the U.S. Government is
subject to restrictions set forth
in subparagraph (c) ( ) (ii) of
the Rights in Technical Data and
Computer Software Clause in
DFARS 252.227-70 3. Agilent
Technologies Inc., 395 Page Mill
Road, Palo Alto, CA 94303-0870
U.S.A. Rights for non-DOD U.S.
Government Departments and
Agencies are set forth in FAR
52.227- 9 (c) ( ,2).
Document Warranty
The information contained in
this document is subject to
change without notice.
Agi ent Techno ogies makes
no warranty of any kind with
regard to this materia ,
inc uding, but not imited to,
the imp ied warranties of
merchantabi ity or fitness for
a particu ar purpose.
Agilent Technologies shall not
be liable for errors contained
herein or for incidental or
consequential damages in
connection with the furnishing,
performance, or use of this
material.
Safety
This apparatus has been
designed and tested in
accordance with IEC
Publication 0 0, Safety
Requirements for Measuring
Apparatus, and has been
supplied in a safe condition.
This is a Safety Class I
instrument (provided with
terminal for protective
earthing). Before applying
power, verify that the correct
safety precautions are taken
(see the following warnings). In
addition, note the external
markings on the instrument that
are described under "Safety
Symbols."
Warning
• Before turning on the
instrument, you must connect the
protective earth terminal of the
instrument to the protective
conductor of the (mains) power
cord. The mains plug shall only be
inserted in a socket outlet
provided with a protective earth
contact. You must not negate the
protective action by using an
extension cord (power cable)
without a protective conductor
(grounding). Grounding one
conductor of a two-conductor
outlet is not sufficient protection.
• Only fuses with the required
rated current, voltage, and
specified type (normal blow, time
delay, etc.) should be used. Do
not use repaired fuses or short-
circuited fuseholders. To do so
could cause a shock of fire hazard.
• Service instructions are for
trained service personnel. To
avoid dangerous electric shock,
do not perform any service unless
qualified to do so. Do not attempt
internal service or adjustment
unless another person, capable of
rendering first aid and
resuscitation, is present.
• If you energize this instrument
by an auto transformer (for
voltage reduction), make sure the
common terminal is connected to
the earth terminal of the power
source.
• Whenever it is likely that the
ground protection is impaired,
you must make the instrument
inoperative and secure it against
any unintended operation.
• Do not operate the instrument
in the presence of flammable
gasses or fumes. Operation of any
electrical instrument in such an
environment constitutes a definite
safety hazard.
• Do not install substitute parts or
perform any unauthorized
modification to the instrument.
• Capacitors inside the
instrument may retain a charge
even if the instrument is
disconnected from its source of
supply.
Safety Symbo s
Instruction manual symbol: the
product is marked with this
symbol when it is necessary for
you to refer to the instruction
manual in order to protect
against damage to the product.
Hazardous voltage symbol.
Earth terminal symbol: Used to
indicate a circuit common
connected to grounded chassis.
WARNING
The Warning sign denotes a
hazard. It calls attention to a
procedure, practice, or the like,
which, if not correctly
performed or adhered to, could
result in personal injury. Do not
proceed beyond a Warning sign
until the indicated conditions
are fully understood and met.
CAUTION
The Caution sign denotes a
hazard. It calls attention to an
operating procedure, practice,
or the like, which, if not
correctly performed or adhered
to, could result in damage to or
destruction of part or all of the
product. Do not proceed
beyond a Caution symbol until
the indicated conditions are
fully understood or met.
!

Product Warranty
This Agilent Technologies
product has a warranty against
defects in material and
workmanship for a period of one
year from date of shipment.
During the warranty period,
Agilent Technologies will, at its
option, either repair or replace
products that prove to be
defective.
For warranty service or repair,
this product must be returned
to a service facility designated
by Agilent Technologies.
For products returned to
Agilent Technologies for
warranty service, the Buyer
shall prepay shipping charges to
Agilent Technologies and
Agilent Technologies shall pay
shipping charges to return the
product to the Buyer. However,
the Buyer shall pay all shipping
charges, duties, and taxes for
products returned to Agilent
Technologies from another
country.
Agilent Technologies warrants
that its software and firmware
designated by Agilent
Technologies for use with an
instrument will execute its
programming instructions when
properly installed on that
instrument. Agilent
Technologies does not warrant
that the operation of the
instrument software, or
firmware will be uninterrupted
or error free.
Limitation of Warranty
The foregoing warranty shall not
apply to defects resulting from
improper or inadequate
maintenance by the Buyer,
Buyer- supplied software or
interfacing, unauthorized
modification or misuse,
operation outside of the
environmental specifications for
the product, or improper site
preparation or maintenance.
No other warranty is
expressed or imp ied. Agi ent
Techno ogies specifica y
disc aims the imp ied
warranties of merchantabi ity
or fitness for a particu ar
purpose.
Exc usive Remedies
The remedies provided herein
are the buyer’s sole and
exclusive remedies. Agilent
Technologies shall not be liable
for any direct, indirect, special,
incidental, or consequential
damages, whether based on
contract, tort, or any other legal
theory.
Assistance
Product maintenance
agreements and other customer
assistance agreements are
available for Agilent
Technologies products. For any
assistance, contact your nearest
Agilent Technologies Sales
Office.
Certification
Agilent Technologies Company
certifies that this product met
its published specifications at
the time of shipment from the
factory. Agilent Technologies
further certifies that its
calibration measurements are
traceable to the United States
National Institute of Standards
and Technology, to the extent
allowed by the Institute’s
calibration facility, and to the
calibration facilities of other
International Standards
Organization members.
About this edition
This is the E8041A IA-32
478-Pin Interposer
Installation Quick Start
Guide.
Publication number
E804 -9200 , October, 200
Printed in USA.
Print history:
E804 -92000, restricted version
Many product updates do not
require manual changes, and
manual corrections may be done
without accompanying product
changes. Therefore, do not
expect a one-to-one
correspondence between
product updates and manual
updates.
Manual Part Number E804 -9200 October 200 , Printed in USA
*E8041-92001*
*E8041-92001*