Agilent Technologies E5900B User manual

S1
User’s Guide
Publication number E3454-97006
February 2002
© Copyright gilent Technologies, Inc. 1994-2002
ll Rights Reserved
For Safety information, Warranties, and Regulatory information,
see the pages behind the index.
Emulation for the
PowerPC 400/600/700

2 Agilent Technologies Emulation for the PowerPC 400/600/700
Agilent Technologies E 900B Option 060/070
Emulation Probe—At a Glance
This manual describes how to set up:
• an emulation probe
• an emulation module
• an emulation migration
The emulation probe provides a low-cost way to debug embedded software for
PowerPC 400/600/700 family microprocessors. The emulation probe lets you
use the target processor’s built-in debugging features, including: run control,
register access, and memory access. high-level source debugger can use the
emulation probe to debug code running on the target system.
The emulation probe can be controlled by a debugger on a host computer or
by the Emulation Control Interface on an gilent 16700-series logic analysis
system. The emulation probe communicates with a host computer or logic
analysis system via L N.
E5900B Emulation Probe
Host
Computer
E5900B
Emulation Probe
LAN Cable
Target System
Power Supply

Agilent Technologies Emulation for the PowerPC 400/600/700 3
E5901B Emulation Module Kit
The gilent E5901B emulation module kit includes the E5900B emulation
probe, the E5901B emulation module, and other items listed on page 22. The
gilent E5901B emulation module plugs into your gilent 16700-series logic
analysis system frame. It provides power, cross triggering, and limited
communication for the E5900B emulation probe through the module/probe
interconnect cable. The logic analysis system communicates with the target
system through the L N connection to the E5900B emulation probe.
E5902B Emulation Migration Kit
The emulation migration includes the parts needed to use an emulation probe
for a new processor family.
Emulation Solution
If you have an E9xxxB emulation solution, refer to the appropriate Logic
Analysis Support User’s Guide (or Solutions User’s Guide) for information
on how to connect the analysis probe, then return to this book for information
on connecting the emulation probe.
Logic Analysis
System
Target System
E5901B Emulation Module
E5900B Emulation Probe
Module/Probe Interconnect Cable
LAN Cable

4 Agilent Technologies Emulation for the PowerPC 400/600/700
In This Book
Emulation Probe
Processor supported Product ordered Includes
PPC401 (all), PPC403 (all),
PPC405 (all), NPe405H,
NPe405L, PPC440A4,
PPC440GP.
PPC603e rev. 1, 3, 4, 5;
MPC603e; PPC603ev rev. 2,
12; PPC603e2; MPC603P;
MPC603ec; MPE603R;
MPC603ei.
PPC740/50, MPC740/50,
PPC750M, MPC740P/50P,
MPC745/55, PPC750CX,
PPC750CXe.
E5900B Option #060
E5900B Option #060
E5900B Option #070
E5900B #060 emulation probe, cables,
software, and manual.
E5900B #060 emulation probe, cables,
software, and manual.
E5900B #070 emulation probe, cables,
software, and manual.
Emulation Module Kit
Processor supported Product ordered Includes
PPC400-series
(Versions listed above.)
PPC600-series
(Versions listed above.)
PPC700-series
(Versions listed above.)
E5901B Option #060
E5901B Option #060
E5901B Option #070
E5901B emulation module, E5900B #060
emulation probe, cables, software, and
manual.
Emulation Migration Kit
Processor supported Product ordered Includes
PPC400-series
(Versions listed above.)
PPC600-series
(Versions listed above.)
PPC700-series
(Versions listed above.)
E5902B Option #060
E5902B Option #060
E5902B Option #070
Target board adapter, front panel, tool kit,
cables, software, and manual.

Agilent Technologies Emulation for the PowerPC 400/600/700 5
The E5900B emulation probe has been programmed with firmware at the
factory.
The firmware is a driver that lets the emulation probe communicate with a
certain family of processors. Consult the chart on page 136 to determine
whether the factory-loaded firmware is compatible with your target processor.
If not, you will need to update the firmware as described in Chapter 10,
“Updating Firmware,” beginning on page 135.
In this manual "PowerPC" is used to refer to both the IBM PPC family of
PowerPC processors and the Motorola MPC family of PowerPC processors.
Emulation Solution
Processor supported Product ordered Includes
PPC603e rev. 1, 3, 4, 5;
MPC603e; PPC603ev rev. 2,
12; MPC603ei.
E9487B Option #001 E5901B emulation module, E5900B #060 or
E5900B #070 emulation probe, cables,
software, and manual, plus analysis
software as described in the Logic Analysis
Support User’s Guide.
PPC603e rev. 1, 3, 4, 5;
MPC603e; PPC603ev rev. 2,
12.
E9487B Option #002 Everything in the E9487B Option #001 and
the 240-pin PQFP analysis probe.
PPC740/50, MPC740/50,
PPC750M, MPC740P/50P,
MPC745/55, PPC750CX,
PPC750CXe.
E9486B Option #001 E5901B emulation module, E5900B #070
emulation probe, cables, software, and
manual, plus analysis software as
described in the Logic Analysis Support
User’s Guide.

Contents
7
gilent Technologies E5900B Option 060/070 Emulation Probe—
t a Glance 2
In This Book 4
1Overview 17
Setup Flowchart 19
gilent E5900B Emulation Probe 20
Equipment supplied 20
Minimum equipment required 20
gilent E5901B Emulation Module Kit 22
Equipment supplied 22
Minimum equipment required 22
gilent E5902B Emulation Migration Kit 24
Equipment supplied 24
Minimum equipment required 24
To connect the emulation probe to a power source 26
Connection Sequence 27
To power on the system 27
To power off the system 27
dditional Information Sources 28
!

8
Contents
2Designing a arget System for an Emulation
Probe 29
Target System Requirements 30
PowerPC JT G interface connections and resistors 34
3Connecting the Emulation Probe
to a LAN 37
To choose a point-to-point or site L N connection 38
Connecting the Emulation Probe to a Site L N 40
To obtain an IP address 41
To configure L N parameters using a serial connection 42
To configure L N parameters using DHCP 45
What is DHCP? 46
How does the emulation probe use DHCP? 46
How does DHCP interact with other methods of setting L N parameters? 46
To configure L N parameters using a logic analysis system without an emula-
tion module 47
To configure L N parameters using a logic analysis system with an emulation
module 48
Setting up a Point-to-Point Connection 49
To set up a point-to-point connection with an emulation module 49
To set up a point-to-point connection without an emulation module 50
Verifying L N Communications 51
To verify L N communications using ping 51
To verify L N communications using telnet 52

Contents
9
4Installing the Emulation Module 53
To install the emulation module in an gilent 16700-series logic analysis sys-
tem or expansion frame 55
To connect the E5901B emulation module to the E5900B emulation
probe 57
5Installing Software on a 16700-Series Logic
Analysis System 59
Installing and loading 60
What needs to be installed 61
To install the software from CD-ROM 62
To list software packages which are installed (16700) 63
6Connecting the Emulation Probe to Your arget
System 65
To connect the emulation probe to the target system 67
7Configuring the Emulation Probe 69
What can be configured 71
Using the cf Commands 72

10
Contents
Configuration items 74
Default configuration 74
To configure the processor type 74
To configure the processor version using the procs command (PowerPC 740P
and 750P) 75
To configure the JT G test clock (TCK) speed (communication speed) 76
Configuring the Emulation Probe for Maximum Performance 77
To configure restriction to real-time runs
( ll processors) 78
To configure reset operation 79
To configure reset vector address
(PowerPC 603ei, 745, 755) 81
To configure power on reset operation
(PowerPC 745, 755) 81
To set the freeze timers option
(PowerPC 400) 82
To enable branch folding
(PowerPC 400) 83
To enable or disable address validation
(PowerPC 400) 84
To enable fast memory loads
(PowerPC 400) 85
To configure the memory model
(PowerPC 603ei, 745, 755) 86
To configure the memory read operation
(PowerPC 400, 603e, 603ev, 603e2, 603P, 603ec, 603R, 740, 750, 750M, 740P,
750P) 87
To configure data memory write operations
(PowerPC 400, 603e, 603ev, 603e2, 603P, 603ec, 603R, 740, 750, 750M, 740P,
750P) 88
To configure instruction memory write operations
(PowerPC 400, 603e, 603ev, 603e2, 603P, 603ec, 603R, 740, 750, 750M, 740P,
750P) 89
To set the memory read delay clock cycles
(PowerPC 603ei, 745, 755) 91