Agilent Technologies E4402BU User manual

Agilent Technologies
E4402BU Option H3B
Installation Guide
Use this manual with the following documents:
The ESA-E Service Document Kit includes:
ESA Service Guide
Calibration Guide
Manufacturing Part Number: E4402-90109
Printed in USA
May 2006
© Copyright Agilent Technologies, Inc. 2006

2
Warranty Statement
THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT
TO BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL
WARRANTIES, EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND
ANY INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. AGILENT SHALL NOT BE LIABLE FOR ERRORS OR FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT OR ANY INFORMATION CONTAINED HEREIN.
SHOULD AGILENT AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH
WARRANTY TERMS COVERING THE MATERIAL IN THIS DOCUMENT THAT CONFLICT
WITH THESE TERMS, THE WARRANTY TERMS IN THE SEPARATE AGREEMENT WILL
CONTROL.
DFARS/Restricted Rights Notice
If software is for use in the performance of a U.S. Government prime contract or
subcontract, Software is delivered and licensed as “Commercial computer software” as
defined in DFAR 252.227-7014 (June 1995), or as a “commercial item” as defined in FAR
2.101(a) or as “Restricted computer software” as defined in FAR 52.227-19 (June 1987) or
any equivalent agency regulation or contract clause. Use, duplication or disclosure of
Software is subject to Agilent Technologies’ standard commercial license terms, and
non-DOD Departments and Agencies of the U.S. Government will receive no greater than
Restricted Rights as defined in FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users
will receive no greater than Limited Rights as defined in FAR 52.227-14 (June 1987) or
DFAR 252.227-7015 (b)(2) (November 1995), as applicable in any technical data.

3
Safety Notes
The following safety notes are used throughout this document. Familiarize yourself with
each of these notes and its meaning before performing any of the procedures in this
document.
WARNING Warning denotes a hazard. It calls attention to a procedure
which, if not correctly performed or adhered to, could result in
injury or loss of life. Do not proceed beyond a warning note
until the indicated conditions are fully understood and met.
CAUTION Caution denotes a hazard. It calls attention to a procedure that, if not
correctly performed or adhered to, could result in damage to or
destruction of the instrument. Do not proceed beyond a caution sign
until the indicated conditions are fully understood and met.
Definitions
• Specifications describe the performance of parameters covered by the product warranty
(temperature – 0 to 55 °C, unless otherwise noted.)
•Typical describes additional product performance information that is not covered by the
product warranty. It is performance beyond specification that 80% of the units exhibit
with a 95% confidence level over the temperature range 20 to 30 °C. Typical
performance does not include measurement uncertainty.
•Nominal values indicate expected performance, or describe product performance that is
useful in the application of the product, but is not covered by the product warranty.

4

Contents
Contents-1
E4402BU Option H3B
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Verifying the Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Removing the Rear Panel and Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting the Cable to the 1st LO AUX OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Assembling the Option H3B Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Performance Tests and Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Safety and Regulatory Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Before Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connector Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Shipping Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Compliance with Canadian EMC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Compliance with German Noise Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Instrument Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Contacting Agilent Sales and Service Offices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Contents-2
Contents

Installation Guide 1
E4402BU Option H3B

2Installation Guide
E4402BU Option H3B Introduction
Introduction
This installation procedure provides instructions for installing the E4402BU Option H3B
into a standard E4402B ESA Spectrum Analyzer. The Option H3B can occupy Slot 5 or 6.
Refer to the E4402B Option H3B User’s and Service Guide (E4401-90511) for performance
verification.
The Agilent Technologies E4402B Option H3B provides a local oscillator output on the rear
panel of the ESA using an SMA (f) connector, for use with the Aerodynex Sideband
Adapter (ATSA–N/P–06R2–AG) for TV modulator and transmitter measurements. This
option is not compatible with option 1DN, Tracking Generator.

Installation Guide 3
E4402BU Option H3B Description
Description
The Agilent Technologies E4402B Option H3B provides a local oscillator output on the rear
panel of the ESA using an SMA (f) connector, for use with the Aerodynex Sideband
Adapter (ATSA–N/P–06R2–AG) for TV modulator and transmitter measurements. This
option is not compatible with option 1DN, Tracking Generator.
The center frequency of the first LO output is 3.9214 GHz when the E4402B is tuned to a
center frequency of 0 Hz, and is 4.9214 GHz when the E4402B is tuned to a center
frequency of 1 GHz.
The nominal output power of the LO Output is ≥–5 dBm from 3.9214 GHz to 4.9214 GHz
and is ≥–10 dBm for center frequencies greater than 1 GHz.
Any device connected to this output must have a 50 Ωimpedance. Included with special
Option H3B is a 50 Ωload that is to be installed on the 1st LO Output connector when not
in use. Failure to terminate the output connector with a 50 Ωload may degrade the
frequency response of the E4402B.
The Agilent Technologies E4402B Option H3B is not compatible with the Tek 1405
sideband adapter or the Aerodynex ATSA–N/P–06R1–TX.
In all other respects, the Agilent Technologies E4402B Option H3B is the same as a
standard E4402B.

4Installation Guide
E4402BU Option H3B Verifying the Shipment
Verifying the Shipment
Inspect the shipping container. If the container or packing material is damaged, it should
be kept until the contents of the shipment have been checked mechanically and electrically.
If there is physical damage please notify the nearest Agilent Technologies office. Refer to
“Contacting Agilent Sales and Service Offices” on page 17. Keep the damaged shipping
materials (if any) for inspection by the carrier and an Agilent Technologies representative.
Installation Information
Table 1 Content List
Description Agilent Part
Number Qty
Spiral Wrap 0890-0025 0.356 meter
Adapter 1250-1666 1
50 Ohm Load 1810-0118 1
Hex Nut 2950-0223 1
Washer 3050-0420 1
Cable Assembly 5062-6665 1
Rear Panel (H3B) E4401-00085 1
User’s and Service Guide E4401-90511 1
Installation Guide (H3B) E4402-90109 1
Products Affected: E4402B ESA-E
To Be Performed By: (X) Agilent Service Center
(X) Personnel Qualified by Agilent
Estimated Installation Time:
Estimated Adjustment and Verification Time:
1 Hour
1 Hour
Performance Test and Adjustments Page 12