Agilent Technologies E5071CU 028 User manual

Agilent E5071CU Option 028
Hard Disk Drive Kit
User’s Guide
First Edition
Manufacturing No. E5071-90133
August 2011

2
Notices
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright.All rights
are reserved. No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of the Agilent Technologies.
© Copyright 2011 Agilent Technologies
Manual Printing History
The manual’s printing date and part number indicate its current edition. The printing date
changes when a new edition is printed. (Minor corrections and updates that are
incorporated at reprint do not cause the date to change.) The manual part number changes
when extensive technical changes are incorporated.
August 2011 First Edition
Typeface Conventions
Sample (bold) Boldface type is used when a term is defined or
emphasis.
Sample (Italic) Italic type is used for emphasis.
key Indicates a hardkey (key on the front panel or
external keyboard) labeled “Sample.” “key” may
be omitted.
Sample menu/button/box Indicates a menu/button/box on the screen labeled
“Sample” which can be selected/executed by
clicking. “menu,” “button,” or “box” may be
omitted.
Sample block/toolbar Indicates a block (group of hardkeys) or a toolbar
(setup toolbar) labeled “Sample.”
Sample 1 - Sample 2 - Sample 3 Indicates a sequential operation of Sample 1,
Sample 2, and Sample 3 (menu, button, or box).
“-” may be omitted.

3
1 General Information
This chapter describes the Hard Disk Drive Kit, contents of the kit, and required tools to
install the Option 028 into the Agilent E5071C.

4 Chapter 1
General Information
Option 028 Hard Disk Drive Kit
Option 028 Hard Disk Drive Kit
The purpose of this kit is to install the option 028 into the Agilent E5071C.
Contents of the Agilent E5071CU Option 028 Upgrade Kit
The kit includes the parts listed in Table 1-1. If anything is missing, contact the nearest
Agilent Technologies office.
Table 1-1 Contents of the Agilent E5071CU Option 028 Upgrade
Kit
Description Qty.
Upgrade Manual (This manual) 1
Hard Disk for E5071C 1

5
2 Option Installation
This chapter describes the procedure to install the Option 028 into the Agilent E5071C.

6 Chapter 2
Option Installation
Introduction
Introduction
This chapter describes the procedure to install Option 028 into the E5071C. The procedure
consists of the following items.
•Installation Requirement
•Backing Up Option Data
•Removal Procedure
•Replacement Procedure
•Restoring Option Data
•Writing System Correction Data of Backup Memory to Removable HDD
•Reconfiguring Touch Panel Settings
•Calibration of the Touch Screen
Update Procedure for Hard Disk
This procedure is for screw type hard disk.
Installation Requirement
• 5188-4426 Key for Hard Disk Carrier
Backing Up Option Data
Step 1. Copy RECOVERY(E):\LICENSE\gen.lic from the original HDD to USB pen drive.
NOTE The license keys are kept in a text file (.lic) located at RECOVERY(E):\LICENSE\gen.lic.
When you change the removal hard disk, copy the file as back up. Even if you lost the file,
you can activate the option again if you have the license number. You can re-create the
license number at http://www.agilent.com/find/softwarelicense with your software
entitlement certificate..

Chapter 2 7
Option Installation
Update Procedure for Hard Disk
Removal Procedure
Step 1. Turn off the power.
Step 2. Inset the key in the lock and turn anti-clockwise.
Step 3. Open the screw in clockwise direction.
Step 4. Press the button under the screw.
Step 5. Remove the hard disk.
Replacement Procedure
Step 1. Insert the hard disk into the slot.
Step 2. Turn the screw in anti-clockwise direction until it is locked..
Step 3. Turn the key to the right until it is locked.
Step 4. Remove the key.
Step 5. Turn on the E5071C.
Restoring Option Data
Step 1. Paste the gen.lic file to RECOVERY(E):\LICENSE\ on Spare-HDD from the USB pen
drive.

8 Chapter 2
Option Installation
Update Procedure for Hard Disk
Writing System Correction Data of Backup Memory to Removable
HDD
The following is a description of the procedures to write the system correction data stored
in the backup memory to the mounted removable HDD.
Step 1. Turn on the E5071C.
CAUTION The function for Factory image making window is only displayed when E5071C is turned
on for the first time.
Step 2. Press
Step 3. Press Load Project... on the softkey menu.
Step 4. A dialog box appears to allow you to select a program to be loaded. Select
RestoreSysCorFile.vba from the D:\Agilent\Service folder, and then press Open button.
Step 5. Press
Step 6. RestoreSysCorFile dialog box appears (Figure 2-1). Click OK.
Figure 2-1 RestoreSysCorFile Dialog Box
CAUTION Once the program has ended, restart the E5071C to enable the system correction data.
CAUTION If touch screen does not work after the installation, refer to "Reconfiguring Touch Panel
Settings".
Step 7. Calibrate the touch screen by referring to Calibration of the Touch Screen.

Chapter 2 9
Option Installation
Update Procedure for Hard Disk
Reconfiguring Touch Panel Settings
The following is a description of the procedures to reconfigure touch panel settings.
Step 1. In E5071C, right click My Computer..
Step 2. Select Properties. The System Properties dialog appears
Step 3. Select Hardware tab.
Step 4. Click Device Manager.
Step 5. Select Ports (COM & LPT).
Step 6. Check if two Communication Port (COM1) are displayed.
Step 7. Right click and select Uninstall (Figure 2-2) for both the COM1 ports.
Figure 2-2 Device Manager
Step 8. The Confirm Device Removal message appears. Click OK.
Step 9. Reboot the instruments.

10 Chapter 2
Option Installation
Update Procedure for Hard Disk
Calibration of the Touch Screen
When you have replaced the HDD on an E5071C, you have to calibrate the touch screen.
Follow the procedure described below to calibrate the touch screen.
Step 1. Press .
Step 2. Press Service Menu.
Step 3. Press Test Menu.
Step 4. Press Adjust Touch Screen.
The touch screen calibration screen (Figure 2-3) appears.
Figure 2-3 Touch Panel Calibration Screen
Step 5. Touch the x mark on the upper left with your finger. The mark x appears also on the lower
left, upper right, and lower right. Touch the x marks in that order with your finger.
Touching the four locations described above with your finger automatically concludes the
touch screen calibration.
NOTE With no operation on the touch screen calibration screen for a preset time, it automatically
closes and the previous measurement screen reappears.

© Agilent Technologies, Inc. 2011
Printed in Malaysia
First edition, August 2011
*E5071-90133*
E5071-90133
www.agilent.com
Agilent Technologies