Agit Wave Storm User manual

AGIT GLOBAL, INC.
No. 14-1, Sec. 1, Shinren Road, Taiping City, Taichung, 411 Taiwan R.O.C.
www.agit-global.com
[email protected]
1-877-673-3622
USER’S MANUAL
10 FOOT 6 STAND UP PADDLE BOARD

INDEX
Board Care Information
Contents
Fin Installation
Leash Installation
Paddle Installation
PAGE 05
PAGE 04
PAGE 06
PAGE 08
PAGE 10
2
1
3
4
5
Thank You for purchasing a ‘Wave
Storm’ Stand-Up Paddle Board
(SUP) and we hope you have fun
using your new purchase as much as
we’ve enjoyed developing and testing
this SUP.
Stand-Up Paddle Boarding, or in
Hawaiian language, Hoe he’e nalu,
is an emerging global sport with a
Hawaiian heritage. The sport is an
ancient form of surfing that began
as a method for surfing instructors
to manage large groups of learner
surfers. Standing on the board gave
instructors a higher viewpoint,
increasing visibility of what was going
on around them - such as an incoming
swell or wave. In the early 1960s, The
Beach Boys of Waikiki would stand on
their long boards and paddle out with
outrigger paddles to take pictures of
tourists learning to surf. This is where
the term “Beach Boy Surfing”, another
name for Stand-Up Paddle Surfing,
originates.
The sport provides an excellent Core
Workout because it requires good
core strength to balance and paddle
on the board while standing on an
unstable water surface. SUP’ing can be
done on oceans, lakes, and rivers. It is
gaining in popularity as celebrities are
practicing the sport, and cross-over
athletes are training with SUP’s. Many
surfers have converted to SUP’ing
because of the versatility of this new
sport; it can be done on days when
there is surf (waves) or when there are
no waves at all.
AGIT Global’s 10 foot 6 inch Wave
Storm SUP is designed for beginners
to advanced SUP’ers alike. Our board
dimensions provide good stability on
water. The foam construction of the
board, with its 3 Stringer design is
very strong yet light-weight and is
easy to transport. There is a Built-In
Handle near the center of the topdeck
to help carry the board. There is a Fin
in the stern for added stability.
The Wave Storm SUP also features
our patented ‘Water Barrier Skin’
technology, a thin graphic film layer
covering the board’s topdeck, giving
protection from minor scratches,
dents and abrasions. It helps keep the
SUP looking clean and fresh.
The length of the Wave Storm Paddle
is approximately 82” (208cm). The
Paddle can easily be adjusted to
accommodate the desired height of
most riders. Typically, a rider needs a
Paddle extending from the bottom of
their feet to a few inches above their
head.
Please read through the instruction
manual to properly install the Fins
and Leash. We hope you enjoy your
new Wave Storm SUP but remember...
Always Carefully Examine Water
Conditions in your area, making
sure it is clear of Rocks, Reefs, Boats
and other Inherent Water Hazards.
We highly recommend wearing only
approved US Coast Guard Personal
Flotation Devices (PFD) while SUP’ing.
SUP’ing can be safer and loads fun
when practicing with a buddy.
ALOHA from the Wave Storm team!
02 03
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual

CONTENTS BOARD CARE INFORMATION
04 05
HANDLE STEM x1
FIN x1LEG LEASH x1
ADHESIVES
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
1 2
3 4
1 2
We strongly suggest removing the fin when transporting the
board to prevent damage.
Rinse your board with fresh water after every use to remove dirt,
sand, and salt residue.
If possible, please store your board away from direct sunlight, in
a cool, dry location.
If your board has a hole or scratch in the foam surface, you can
purchase any “Non-Solvent” based glue to repair it. Spread the
glue inside the hole or scratch and let dry before using.
You can also use any “Non Solvent” based glue to repair side rail
seams (where the slick bottom and foam surface join together).
Spread the glue in seam and let dry before using the board.
Fins, Leashes, Paddles, Protective Board Covers are available for
purchase. Please call 1-877-673-3622 for more information or
visit www.agit-global.com
1
2
3
4
5
6

FIN INSTALLATION
06 07
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
Slide metal plate forward, as shown above.
1
DO NOT USE EXCESSIVE FORCE
WHEN TIGHTENING SCREWS.
Caution
3
Insert Fin into fin box by inserting brass pin of Fin into the opening of
fin box, as shown above.
Slide Fin backwards into position,
as shown above.
Push Fin down, as shown above.
2
2.2
Fin
Fin Fin
Fin
2.1
2.3
Attach Fin to metal plate with
screw, as shown above. Do not
tighten yet.
Screw
Metal Plate
3
Adjust Fin position by sliding
forward or backwards to desired
position. Then tighten screw. Do
not over tighten screw.
4
Back
Metal Plate
Fin Box

LEASH INSTALLATION
08 09
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
Pull Leg Leash Rope through eyelet as shown
above.
1
Pull leg cuff through Leg Leash Rope as
shown above.
2
Pull Leg Leash Rope tight. Installation complete.
3
4

10
10
11
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
10 FOOT 6 STAND UP PADDLE BOARD
User’s Manual
Caution
c
STEPS FOR ADJUSTING PADDLE LENGTH
a
b
d
Use a Tape Measure to determine proper length. Measure from the
bottom of your feet(floor) to 4” above your head. This measurement
should be good for determining the overall length of your new Paddle.
Each user has different preferences, so be sure this length works for
you before applying the glue. This process is only meant help assist
you determine what overall length should work for you. Keep in mind,
cutting the tube & applying glue are permanent procedures, so be very
sure of your measurements.
Cut Paddle tube with a hack saw. Then use the included nail file to
smooth edges of your cut.
RE-ATTACHING HANDLE TO PADDLE TUBE
CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS
1-877-673-3622
Your new Paddle as it comes inside the box, measures 82” (208cm)
from tip to tip.
As an option
, you can adjust the Paddle length to
properly fit your desired length. However, if you choose not to adjust
Paddle length, then move directly to Step-D.
• PLEASE USE GLUE WITHIN 60 SECONDS AFTER MIXING.
• PLEASE KEEP GLUE KIT IN DRY, COOL PLACE FOR STORAGE.
• KEEP OUT OF REACH OF CHILDREN.
• WASH HANDS THOROUGHLY WITH SOAP AND WATER AFTER APPLICATION.
PADDLE
SIZING & INSTALLATION
5
Nail file
4”
Tape Measure
c
a
b
e
F
d
A+B
1:1
1:1
Mixed
Match up
1
Protect your work area from excess glue dripping from the following process.
2
Wipe clean the joint surfaces of Paddle tube & Handle to be joined.
3
Mix glue (A) & (B) well with equal portions.
4
Apply mixed glue to outer surface of Handle stem only.
5
Instert Handle stem into Paddle tube & make sure the silver lines match up.
6
Hold into position for 5-minutes.
7
After 5-minutes, continue allowing glue to dry properly for 30-minutes
before using.
8
Clean up excess glue.
Remove loose Handle from top of Paddle tube. Measure the amount of
tubing to be removed to achieve your desired Paddle length.
FINISHED
FINISHED