AGM Global Vision FUZION User manual

USER MANUAL
FUZION
FUSION THERMAL & OPTICAL
BI-SPECTRUM MONOCULAR

© 2021 AGM Global Vision, LLC. All rights reserved.
This documentation is subject to change without notice.
No parts of this manual, in whole or in part, may be copied, photocopied, translated,
or transmitted by any electronic medium or in machine-readable form without the
prior written permission of AGM Global Vision, LLC.
If you have questions that are not covered in this manual, or need service, contact
AGM Global Vision customer support for additional information prior to returning a
product.
AGM Global Vision, LLC
173 West Main Street
PO Box 962
Springerville, AZ 85938
Tel. [phone]
[e-mail]
www.agmglobalvision.com
EXPORT INFORMATION
Buyer acknowledges thatall productssuppliedbyAGM Global Vision, LLCaresubject
to U.S. export control laws, including, but not limited to, the Export Administration
Regulations, the International Economic Emergency Powers Act, and various U.S.
embargoes and sanctions. AGM Global Vision products may not be exported,
re-exported, or transferred contrary to U.S. export control laws. In particular,
AGM Global Vision products may not be exported, re-exported, or transferred to
prohibited countries, individuals, organizations, or entities, including but not limited
to those individuals and entities listed on the List of Specially Designated Nationals
and Blocked Persons administered or maintained by the U.S. Office of Foreign
Assets Control (“OFAC”), the various lists maintained by the Bureau of Industry
and Security of the Department of Commerce, and the U.S. State Department and
Buyer represents and warrants that neither Buyer nor any of its officers, directors,
or employees are on such lists. Distribution or resale by Buyer to such countries,
individuals, organizations, or entities is expressly prohibited. Buyer has and will
maintain a positive process to ensure compliance with this Section.
2021.10.05

FUZION USER MANUAL 3
FCC INFORMATION
Please take attention that changes or modification not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
This equipment complies with FCC/IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment.
FCC compliance: This product has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This product generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this product does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
EU CONFORMITY STATEMENT
This product and - if applicable - the supplied accessories too
are marked with “CE” and comply therefore with the applicable
harmonized European standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier
or to a designated collection point. For more information see:
www.recyclethis.info
INDUSTRY CANADA ICES-003 COMPLIANCE
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

AGM Global Vision4
LIST OF CONTENTS
TITLE PAGE
Safety Summary 5
1. GENERAL INFORMATION 7
1.1System Description 7
1.2 Key Features 8
1.3 Standard Components 8
2. OPERATING INSTRUCTIONS 9
2.1. Basic Operations 9
2.2 Main Function 14
2.3 Client Software Introduction 20
3. MAINTENANCE 21
3.1 Maintenance 21
3.2 Troubleshooting 22
4. WARRANTY INFORMATION 23
4.1 Warranty Information and Registration 23
5. SPECIFICATIONS 25
5.1 Specifications 25

FUZION USER MANUAL 5
SAFETY SUMMARY
• Read and follow all instructions
• Read all warnings
• Only use the attachments/accessories specified by the manufacturer
• All service must be provided by the manufacturer
WARNING:
This product contains natural rubber latex, which may cause potentially fatal
allergic reactions! If you are allergic to latex, it is important that you strictly
avoid exposure to products that contain it.
WARNINGS AND CAUTIONS:
Transportation
• Keep the device in original or similar packaging while transporting it.
• Keep all wrappers after unpacking them for future use. In case of any failure
occurred, you need to return the device to the factory with the original
wrapper. Transportation without the original wrapper may result in damage
on the device and the company shall not take any responsibilities.
• DO NOT drop the product or subject it to physical shock. Keep the device
away from magnetic interference.
Power Supply
• The battery charger and power adapter are included in the package. The
input voltage for the supplied battery charger should meet the limited power
source (5 VDC, 2 A).
• Make sure the plug is properly connected to the power socket.
• DO NOT connect multiple devices to one power adapter, to avoid over-
heating or fire hazards caused by overload.
Battery
• Improper use or replacement of the battery may result in explosion hazard.
Replace with the same or equivalent type only. The battery type is 18650
with the protection board, and the battery size should be within 19 mm ×
70 mm. The rated voltage and capacity are 3.6 VDC/3.35 Ah (12.06 Wh).
Dispose of used batteries in conformance with the instructions provided by
the battery manufacturer.
• For long-term storage of the battery, make sure it is fully charged every half
year to ensure the battery quality. Otherwise, damage may occur.
• Do not charge other battery types with the supplied charger. Confirm there
is no flammable material within 2 m of the charger during charging.
• DO NOT place the battery near heating or fire source. Avoid direct sunlight.
• DO NOT swallow the battery to avoid chemical burns.
• DO NOT place the battery in the reach of children.
• The device can not be charged, please use the supplied charger to charge
the battery.
• Please purchase the adapter by yourself. The using environment of the
adapter should be consistent with that of the device.

AGM Global Vision6
Maintenance
• If the product does not work properly, please contact your dealer or the
nearest service center. We shall not assume any responsibility for problems
caused by unauthorized repair or maintenance.
• Wipe the device gently with a clean cloth and a small quantity of ethanol, if
necessary.
• If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the device may be impaired.
• Clean the lens with soft and dry cloth or wiping paper to avoid scratching it.
Using Environment
• Make sure the running environment meets the requirement of the device.
The operating temperature shall be -20°C to 55°C (-4°F to 131°F), and the
operating humidity shall be 95% or less.
• DO NOT expose the device to extremely hot, cold, dusty, corrosive, saline-
alkali, or damp environments.
• This device can only be safely used in the region below 2000 meters above
the sea level.
• Avoid equipment installation on vibratory surface or places subject to
shock (neglect may cause equipment damage).
• DO NOT aim the lens at the sun or any other bright light.
NOTES:
• The detector spectral band provides better visibility through smoke, dust,
rain, smog, etc.
• Infrared radiation does not travel through glass. As a result, the monocular
does not detect objects if they are behind glass windows or other barriers.
EMERGENCY:
If smoke, odor, or noise arises from the device, immediately turn off the power,
unplug the power cable, and contact the service center.

FUZION USER MANUAL 7
1 GENERAL INFORMATION
1.1 SYSTEM DESCRIPTION
The AGM Fuzion Handheld Thermal & Optical Bi-spectrum Monocular is
equipped with 12μm high sensitivity thermal detector, ultra-low light optical
detector, 1024×768 OLED display and eyepiece with a large field of view. The
devicecanquicklydetect hidingobjectseven under extreme environments such
as smoke, fog, rain, snow, etc. It can be widely applied to scenarios including
patrol, search and rescue, drug interdiction, and suspect apprehension. Due
to its waterproof capability the device performs well even in severe weather
conditions and challenging environments.
The Fuzion’s user-friendly interface, comfortable and ergonomic operating
controls makes adoption and application incredibly simple. The monocular
offers three different variants of image view: thermal, visible light, and fusion
that can be easily adapted depending on different environmental conditions.
The Fuzion uses one 18650 rechargeable Lithium battery for up to 5-hours of
operating time. In addition, an external power supply can be used to provide an
increase in operating time.
TABLE 1-1. MAIN PARTS
ITEM DESCRIPTION ITEM DESCRIPTION
1Body 7Operation Wheel
2Optical Lens 8Eyepiece
3 Lens Cap 9 USB Type-C Interface
4Thermal Lens 10 Battery Cover
5 Focus Ring 11 Battery Compartment Lock
6Control Buttons 12 Tripod Screw
FIGURE 1-1. MAIN PARTS
1
2
3
4
56789
10
11
12

AGM Global Vision8
1.2 KEY FEATURES
• Bi-spectrum image fusion and object highlight
• Detail enhancement and target recognition
• Selection of thermal view channel, visible light channel, or both
them combined
• 12 μm, 35 mK NETD high sensitivity thermal detector
• Fast 50 Hz imaging
• 1x, 2x, 4x, 8x digital zoom
• Digital image processing technology
• Ultra-low illumination optical channel
• 1920×1080 optical resolution
• 1024×768 resolution, 0.39-inch OLED display
• Video recording and snapshot, built-in EMMC (16 GB)
• Wi-Fi hotspot
• Standby mode
• Up to 5 hours continuous running
• Waterproof
• Limited 3-Year Warranty
1.3 STANDARD COMPONENTS
The standard components are shown in Figure 1-2 and listed in Table 1-2.
The ITEM NO. column indicates the number used to identify items in Figure 1-2.
TABLE 1-2. STANDARD COMPONENTS
ITEM DESCRIPTION QUANTITY
1Monocular 1
218650 Rechargeable Battery 2
3USB Cable 1
4 Battery Charger 1
5Power Adapter 1
6 Lens Cloth 1
7User Manual 1
FIGURE 1-2. STANDARD COMPONENTS
6
7
23
1
4
5

FUZION USER MANUAL 9
2 OPERATING INSTRUCTIONS
2.1. BASIC OPERATIONS
2.1.1 UNPACKING
The following steps must be completed prior to each mission.
1. Open the carrying case,remove themonocular,andverify that all components
are included.
2. Inspect the monocular for any obvious evidence of damage to the optical
surfaces, body, eyecup, operation buttons, etc. Ensure that all optical
surfaces are clean and ready for use. Clean all optical surfaces with a lens
tissue.
2.1.2 BATTERY INSTALLATION
1. Press and push the battery compartment lock (A), rotate the battery cover
(B) anticlockwise until the marks on the battery cover and the device (C) are
aligned, and disassemble the battery cover.
2. Insert the battery (D) into the battery compartment with the positive mark
inward.
3. Align the marks on the battery cover and the device, and put the battery cover
on the battery.
4. Rotate the battery cover clockwise to fix it.
NOTE:
Remove the battery from the battery compartment if the device is not used
for a long time.
A
C
BD
FIGURE 2-1. BATTERY INSTALLATION

AGM Global Vision10
2.1.3 CONTROLS AND INDICATION
The Fusion controls are shown in Figures 2-2 and are defined in Tables 2-2.
Each button is responsible for some functions selected by short press or long
press (hold) the button. Pushing a button for 2+ second is considered “long
press” (hold).
TABLE 2-1. CONTROLS AND INDICATOR FUNCTIONS
ITEM CONTROLS FUNCTIONS
1POWER BUTTON Press: Standby mode/Wake up device.
Hold: Power ON/OFF.
2 CAPTURE BUTTON Press: Capture image.
Hold: Trigger calibration.
3MENU BUTTON Press: Palettes.
Hold: Enter/Exit the menu.
4OPERATION WHEEL Adjusts the digital zoom.
Selects the functions in menu mode.
5POWER INDICATOR Indicate the power ON/OFF.
NOTE:
Press the CAPTURE button and MENU button at the same time to start
or stop recording.
FIGURE 2-2. CONTROLS AND INDICATION
1
52 3 4

FUZION USER MANUAL 11
2.1.4 POWER ON AND OFF
Power On
When the battery is enough, hold the POWER button to power on the device.
Refer to the figure below for the main view of the monocular display.
Power Off
When the device is turned on, hold the POWER BUTTON to power off the
device.
NOTE
See the battery icon on the device display for the electricity quantity. Icon
means the battery is fully charged, and icon means that the battery is low.
When the low power note shows, charge the battery.
In the “Auto Power Off” menu you can set the time for the automatic shutdown
of the device as required (OFF / 30 min. / 45 min.).
2.1.5 STANDBY MODE
In the view mode, press the button. After a few seconds, the display will turn
off. Press the button again to exit the Standby mode.
2.1.6 THERMAL VIEW OBSERVATION
1. Power on the device.
2. Hold the device and make sure the eyepiece covers your eye.
3. Adjust the diopter adjustment ring until the OSD text or image is clear.
4. Point the device towards the target of the view. Bring the object into focus by
rotate the objective focus ring.
NOTE:
You must perform the focus adjustment before any further use of the
riflescope.
5. Set palette, brightness, contrast, scene mode and FFC (Flat Field Correction),
to display the best image effect.
HOT SPOT
TIME AND DATE BATTERY
DIGITAL ZOOM STORAGE
FIGURE 2-3. THE DISPLAY MAIN VIEW

AGM Global Vision12
2.1.7 PALETTE SETTINGS
You can select different palettes to display the same scene in different effects.
Press in live view interface to switch palettes.
TABLE 2-2. PALETTE SETTINGS
PALETTE DESCRIPTION
OPTICAL The image of optical channel is displayed in this mode.
WHITE HOT The hot part is white-colored in view. The higher the
temperature is, the lighter the color is.
BLACK HOT The hot part is black-colored in view. The higher the
temperature is, the more black the color is.
RED HOT The hot part is red-colored in view. The higher the
temperature is, the redder the color is.
FUSION From high temperature to low temperature, the image
is colored in from white, yellow, red, pink to purple.
IMAGE FUSION Fuse the optical image with the thermal image. The
fused image with clear edge is displayed in this mode.
NOTE
When the palette is set as image fusion, you can adjust the fusion level
according to the actual observation distance to obtain better image fusion
effect (see 2.2 for details).
2.1.8 DIGITAL ZOOM
In the live view interface, rotate the operation wheel to switch the digital zoom
of the device (1x, 2x, 4x, or 8x). The image magnification value is displayed on
the screen:
- AGM Fuzion TM25-384: 2.5x, 5x, 10x, 20x
- AGM Fuzion TM35-384: 3.5x, 7x, 14x, 28x
- AGM Fuzion TM35-640: 2x, 4x, 8x, 16x
2.1.9 VIDEO RECORDING / IMAGE CAPTURE
Video Recording
In the live view interface, press and buttons at the same time to start
recording.
The left top of image displays the information of recording time.
Press and buttons at the same time again to stop recording.
Snapshot Capturing
In the main live view interface, press button to capture picture.

FUZION USER MANUAL 13
NOTE:
• When capturing succeeds, the image freezes for 1 second and a prompt
shows on the display.
• For exporting captured pictures, refer to Export Files.
2.1.10 CONNECTING THE DEVICE
1. Open the cable interface cover.
2. Connect the device and PC to copy/delete files.
2.1.11 FILE EXPORT
1. Connect the thermal monocular to your PC with USB cable and open the
detected disk.
2. Open computer disk and select the disk of device. Go to the DCIM folder and
find the folder named after the capture year and month. For example, if you
capture a picture or record a video on June 2021, go to DCIM -> 202106 to
find the picture or video.
- Select and copy the videos to PC and play the file with the player.
- Select and copy the snapshots to PC and view the files.
3. Disconnect the device from your PC.
NOTE:
• The device displays images when you connect it to PC. But functions such as
recording, capturing and hot spot are disabled.
• When you connect the device to PC for the first time, it installs the drive
program automatically.
FIGURE 2-4. VIDEO RECORDING

AGM Global Vision14
2.2 MAIN FUNCTIONS
2.2.1 MENU OPERATION
When the device powers on, hold button to display the menu.
Rotate the operation wheel to move between menu items. The active element
is highlighted in orange. Press button to select menu item or change an
option. Hold button to exit the menu.
TABLE 2-3. MENU FUNCTION
MENU ITEM SYMBOL OPTION FUNCTION
CONTRAST 5 Levels of
contrast Adjust the image contrast.
BRIGHTNESS 5 Levels of
brightness Adjust the image brightness.
SCENE MODE
Recognition Switch between the Recognition
mode and Jungle mode.
Jungle
TRIGGER
CALIBRATION --- Performs the correction as preset
FFC mode.
FFC Auto /
Manual /
External
Select the Flat Field Correction
(FFC) mode.
CVBS
OFF Turn on and off the CVBS Output
function to view the video on
CVBS monitor.
ON
FUSION
LEVEL
<26m,
26~53m,
>53m Switch fusion level.
FIGURE 2-5. THE MAIN MENU

FUZION USER MANUAL 15
MENU ITEM SYMBOL OPTION FUNCTION
DPC --- Correct dead pixel manually.
BURNING
PREVENTION
ON Turn on and off the Burn
Prevention function.
OFF
LANGUAGE 17
Languages Select the language of interface.
VERSION --- View the firmware version
number and serial number.
RESTORE --- Restore the device to defaults.
TIME SYNC. Time Format
/ Time / Date Set the time and date.
OSD
ON Enable or disable OSD.
OFF
AUTO POWER
OFF OFF/30 min/
45 min Set the automatic shutdown time.
HOT
TRACKING
OFF Enable/disable hot spot mark
(marking the spot of highest
temperature).
ON
NETWORK
OFF Enable or disable the Wi-Fi
hotspot.
Hotspot
2.2.2 CONTRAST ADJUSTMENT
1. Hold button to go to the menu.
2. Rotate the wheel to select Contrast menu item and press button to
adjust the image contrast. You can select one of five levels of the contrast.
2.2.3 BRIGHTNESS ADJUSTMENT
1. Hold button to go to the menu.
2. Rotate the wheel to select Brightness menu item and press button to
adjust the brightness.
You can select one of five levels of the brightness to adjust the image lighter
or darker.

AGM Global Vision16
2.2.4 SCENE MODE
You can select proper Scene Mode according to environment temperature to
improve the display effect.
1. Hold button to go to the menu.
2. Rotate the wheel to select / Scene Mode menu item ( is default
option) and press to switch scene.
Recognition mode ( ) improves an image so that the object edge is more
distinct.
Jungle mode ( ) is more suitable for hunting environment because of the
highlight function of small objects.
3. Hold to save settings and exit.
2.2.5 SET FUSION LEVEL
When the palette is set as image fusion, you can adjust the fusion level
according to the actual observation distance to obtain better image fusion
effect.
1. Hold button to go to the menu.
2. Rotate the wheel to select menu item.
3. Press to switch fusion level.
2.2.6 TRIGGER CALIBRATION
Trigger Calibration performs the correction of nonuniformity of display in the
mode preset in the FFS menu.
In the live view interface, hold button to trigger the calibration.
You can trigger the calibration in the main menu also:
1. Hold button to show the menu.
2. Rotate the wheel to select menu item and press to trigger the
calibration.
3. Hold button to exit.
2.2.7 FFC (FLAT FIELD CORRECTION)
Flat Field Correction (FFC) function can correct nonuniformity of display.
1. Hold button to show the menu.
2. Rotate the wheel to select menu item and press to switch the FFC
mode between Manual, Auto and External.
Manual: Enter Trigger Calibration in the menu and press button to correct
the nonuniformity of display (refer to section 2.2.6).
Auto: The monocular performs FFC automatically when switching on or
rebooting the camera.
External: Cover the lens cap, then enter Trigger Calibration in the menu and
press button to correct the nonuniformity of display (section 2.2.6).
3. Hold button to exit.

FUZION USER MANUAL 17
2.2.8 CVBS OUTPUT
You can view the video on CVBS monitor, to get a better and clear image, more
convenient to check the detail.
1. Connect the USB-CVBS cable to USB port of thermal monocular and to
monitor’s CVBS port.
NOTE:
USB-CVBS cable need to be purchase separately.
NOTE:
CVBS Output function doesn’t support hot plug, so please connect the cable
before power on.
2. Hold button to show the menu.
3. Select
CVBS menu item and press button to turn on or turn off the CVBS
video output.
2.2.9 DEFECTIVE PIXELS CORRECTION
Defective Pixels Correction (DPC) function can correct the defective pixels on
the screen which are not performed as expected.
Before you start switch the palettes mode to White Hot mode.
1. Hold button to show the menu.
2. Rotate the wheel to select DPC menu item, and press to enter the DPC
setting interface.
3. Press to switch the moving direction of the cursor, and rotate the wheel to
move the cursor until it reaches the defective pixel.
4. Press to correct the defective pixel.
NOTE:
When Holding in the DPC interface, the menu at the bottom of the interface
can be mirrored to the top of the interface.
The selected defective pixel can be magnified and displayed at the bottom
right of the interface.
FIGURE 2-6. DEFECTIVE PIXELS CORRECTION

AGM Global Vision18
2.2.10 BURNING PREVENTION
This function can prevent damage to the thermal sensor from the sun or other
high temperature bright light source. When enabling this function, the shield
will close until the environment turns to normal.
1. Hold button to go to the menu.
2. Rotate the wheel to select menu item and press button to enable or
disable the Burn Prevention function.
NOTE:
When the burn-prevention function is disabled, the shield won’t be forced to
close in such conditions.
2.2.11 LANGUAGE SETTING
You can select different languages of user interface.
1. Hold button to show the menu.
2. Rotate the wheel to select Language menu item and press button to
select the language.
3. Rotate the wheel to select the language as required, and press to confirm.
2.2.12 VIEW DEVICE INFORMATION
1. Hold button to show the menu of device.
2. Select Version menu item and press button. You can view the device
information such as firmware version, and serial number.
2.2.13 RESTORE DEVICE
You can reset the settings of device.
1. Hold button to show the menu of device.
2. Select Restore menu item and press button to restore the device to
defaults according to the prompt.
2.2.14 TIME SYNCHRONIZATION
1. Hold button to show the menu.
2. Rotate the wheel to select menu and press button to enter the Time
Sync.
3. Press to switch the time system, and rotate the wheel to select the time
and date to be synchronized.
4. Press and rotate the wheel to set the time and date, and press again to
finish the setting.
5. Hold to save settings and exit.
2.2.15 OSD
1. Hold button to go to the menu.
2. Rotate the wheel to select / menu item and press button to switch
the OSD mode.

FUZION USER MANUAL 19
When OSD (On-Screen Display) is on the information such as time, date, Wi-Fi
hotspot activation, digital zoom, storage memory status, and battery status
displays in top right corner of viewfinder.
2.2.16 AUTO POWER OFF
You can set the time for the automatic shutdown of the device as required.
1. Hold button to show the menu of device.
2. Rotate the wheel to select Auto Power Off menu item and press button
to select OFF, 30 min or 45 min.
2.2.17 HOT TRACKING
The device can detect the highest temperature spot in the scene and mark it
on display.
1. Hold button to show the menu.
2. Select / and press button to enable/disable hot spot mark
(marking the spot of highest temperature).
When the hot spot mark is enabled, the mark displays in the spot of the
highest temperature. When the scene changes, the mark moves.
2.2.18 NETWORK CONFIGURATION
Connect your phone to the Wi-Fi hotspot of the monocular, you can configure
the parameters and realize functions of the device.
1. Hold button to show the menu.
2. Select menu item to enable Wi-Fi hotspot function.
3. Turn on the WLAN and connect to the Wi-Fi hotspot.
- Hotspot Name: Wlan-IPTS Serial No.
- Hotspot Password: Last 9 digits of Serial No.
4. Search the client software on App Store (iOS System) or Google PlayTM
(Android System) to download and install the app. T-Vision APP is
recommend.
5. Open the APP and connect your phone with the device. You can view the
interface of monocular on your phone.
NOTE:
When the power is less than 15%, the Wi-Fi hotspot function will be turned off
automatically.

AGM Global Vision20
2.3 CLIENT SOFTWARE INTRODUCTION
We recommend using T-Vision software. Install the client software on
your mobile phone first, and then connect your phone to the hotspot of the
monocular. Refer to section 2.2.18 for details of hotspot connection.
NOTE:
The device password is set by user at first activation. If the password was lost
or forgotten, it can be reset. To make a reset, provide the following action:
1. Hold button to show the menu of device.
2. Move the cursor to menu item and press the button to restore all
parameters to default settings.
1. Run the app and connect the phone or tablet with the device.
2. If the device is inactivated, set the password and activate it. If the device is
activated, enter the password to add it to the app.
3. When the device is added, the live view can be seen. You can view the
interface of the monocular on the software. User can change such image
parameters as brightness, contrast, zoom, palettes directly via phone or
tablet as well as record video on phone/tablet memory.
Fuzion
FIGURE 2-7. CLIENT SOFTWARE
Device [Fuzion]