Agri-Fab 45-03732 User manual

FORM NO. 40921 (08/17/2017)
•Safety
•Assembly
•Operation
•Maintenance
•Parts
PRINTED IN USA
OWNERS
MANUAL
Model No.
45-03732
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
SUN SHADE
the fastest way to purchase parts
www.speedepart.com

2
SAFETY RULES
Any power equipment can cause injury if operated improperly
or if the user does not understand how to operate the
equipment. Exercise caution at all times when using power
equipment.
1. This sun shade does not provide protection against
exhaust fumes, collision, rollover or other accidents.
2. Read the sun shade and vehicle owner's manuals and
know how to operate your vehicle and sun shade before
using the sun shade attachment.
3. Be sure there is adequate ventilation when using the
tractor and sun shade in conned areas.
4. The sun shade will restrict your eld of vision in some
directions.Use extra caution when operating your tractor
with the sun shade attached.
5. Watch out for low tree limbs or other overhead obstructions
that may not previously have interfered with operation of
the tractor.The extra height of the sun shade may cause
these objects to become obstacles.
6. Check the area of operation thoroughly before using the
tractor.
3
6
5
12
4
CARTON CONTENTS
Look for this symbol to point out important safety
precautions. It means — Attention!! Become
alert!! Your safety is involved.
1. Upright Tubes (2)
2. U - Tube
3. Support Rods (3)
4. Top Tubes (2)
5. Vinyl Canopy
6. Base Bracket Assembly

3
HARDWARE PACKAGE
SHOWN FULL SIZE NOT SHOWN FULL SIZE
A
B
G
E
F
C
H
I
J
D
REF. QTY. DESCRIPTION
A 2 Carriage Bolt, 5/16" x 2"
B 4 Hex Bolt, 1/4" x 1-1/2"
C 4 Hex Bolt, 5/16" x 1"
D 2 Hex Bolt, 1/4" x 3/4"
E 6 Nylock Nut, 1/4"
REF. QTY. DESCRIPTION
F 6 Flat Washer, 5/16"
G 4 Adhesive Pad
H 2 Plastic Knob
I 2 Plastic Cap
J 2 Support Bracket

4
TOOLS REQUIRED FOR ASSEMBLY
(2) 7/16" Wrenches
(1) 1/2" Socket Wrench
REMOVAL OF PARTS FROM CARTON
• Remove all parts and hardware packages from the
carton. Lay out parts and hardware and identify using
the illustrations on pages 2 and 3.
NOTE: Not all of the supplied parts and hardware will be
needed for one particular tractor. Unneeded items may be
discarded after assembly has been completed.
NOTE: Right hand (RH) and left hand (LH) are
determined from the operator's position while seated on
the tractor.
CAUTION: Make sure tractor seat raises
and lowers freely after attaching Sun
Shade. The tractor's operator presence
safety switch will not operate if seat is
stuck down.
1/4" x 3/4" HEX BOLT(D)
1/4" NYLOCK NUT (E)
ADHESIVE PAD (G)
FOR LAWN TRACTORS ONLY. SKIP TO
STEP 3 IF YOU HAVE A GARDEN TRACTOR
STEP 1: (SEE FIGURE 1)
• Attach the two support brackets to the base bracket
assembly using two 1/4" x 3/4" hex bolts (D) and 1/4"
nylock nuts (E).
• Attach an adhesive pad (G) to each support bracket.
(LT) LAWN TRACTOR
FIGURE 1
FIGURE 2
STEP 2: (SEE FIGURE 2)
• Raise the tractor seat and remove the seat springs
and four bolts from the rear fender using a 1/2" socket.
• Place the support brackets against the rear of the
fender.
• Attach the base bracket assembly and the seat
springs to the fender using the four 5/16" x 1" bolts
(C) and 5/16" washers (F) supplied with the sun
shade. Tighten the bolts using moderate force.
Overtightening might damage the threaded holes in
the fender.
• Insert the plastic caps into the ends of the base
bracket tube.
(LT) LAWN TRACTOR
5/16" x 1"
HEX BOLT (C)
SPRING
5/16" WASHER (F)
SUPPORT BRACKETS
PLASTIC
CAP
5/16" x 1"
HEX BOLT (C)
5/16" WASHER (F)

5
FIGURE 4
STEP 4: (SEE FIGURE 4)
• Assemble the upright tubes to the holes in the base
assembly using a 5/16-18 x 2" carriage bolt (A), 5/16"
at washer (F) and plastic knob (H) for each tube.
5/16" x 2"
CARRIAGE BOLT (A)
5/16" FLAT
WASHER (F)
PLASTIC
KNOB (H)
5/16" x 1"
HEX BOLT (C)
SPRING
5/16" WASHER (F)
HOOKED ENDS
PLASTIC
CAP
5/16" x 1"
HEX BOLT (C)
5/16" WASHER (F)
FIGURE 3
STEP 3: (SEE FIGURE 3)
• Raise the tractor seat and remove the seat springs
and four bolts from the rear fender using a 1/2" socket.
• Place the hooked ends of the base bracket assembly
underneath the rear of the fender as shown.
• Attach the base bracket assembly and the seat
springs to the fender using the four 5/16" x 1" bolts
(C) and 5/16" washers (F) supplied with the sun
shade. Tighten the bolts using moderate force.
Overtightening might damage the threaded holes in
the fender.
• Insert the plastic caps into the ends of the base
bracket tube.
(GT) GARDEN TRACTOR
FOR GARDEN TRACTORS ONLY FOR ALL TRACTORS

6
OPERATION
MAINTENANCE
Read this owner's manual and safety rules before
operating your tractor with the sun shade.
CAUTION: Watch out for low tree limbs and
other overhead objects which may interfere
with the sun shade.
CAUTION: Never transport the tractor in an
open truck or open trailer while the sun shade
is attached.
CAUTION: This sun shade does not provide
protection against exhaust fumes, collision,
rollover or other accidents.
1. Check the area of operation thoroughly before using the
tractor with the sun shade. The added height of the sun
shade and a reduced eld of vision require extra caution
during operation.
2. Remove the upper sun shade frame and canopy before
you transport the tractor in an open truck or open trailer.
CHECK FOR LOOSE FASTENERS
1. Before each use make a thorough visual check of the sun
shade for any bolts and nuts which may have loosened.
Retighten any loose bolts and nuts.
CLEANING
2. Wipe loose dirt and debris from the vinyl canopy after
each use. The vinyl canopy can be washed using mild
liquid soap and water.
STORAGE
1. Clean the vinyl canopy thoroughly with mild liquid soap
and water. Allow to dry before storing.
2. Store the sun shade in a clean, dry area away from direct
sun light.
STEP 6: (SEE FIGURE 6)
• Place the vinyl canopy on top of the tubing frame,
tting the front of the vinyl canopy around the front
U-tube. Secure the nylon mesh to the upright tubes
using the ties located on the corners of the mesh.
FIGURE 6
FIGURE 5
STEP 5: (SEE FIGURE 5)
• Assemble the top tubes to the upright tubes using
two 1/4" x 1-1/2" hex bolts (B) (outside) and two 1/4"
nylock nuts (E) (inside). Do not tighten yet.
• Fit the front U-tube onto the top tubes. Fasten the
tubes together using two 1/4" x 1-1/2" hex bolts
(B) (outside) and two 1/4" nylock nuts (E) (inside).
Tighten all loose bolts and nuts.
• Fit the three support rods into the holes in the top
tubes, with the rods arching upward. Do not over
bend the rods when installing.
1/4" NYLOCK
NUT (E)
U-TUBE
1/4" x 1-1/2"
HEX BOLT (B)
SUPPORT ROD
1/4" x 1-1/2"
HEX BOLT (B)
1/4" NYLOCK
NUT (E)
TOP TUBES

7
2
2
4
3
3
5
14
10
11
8
15
16
10
11
6
13
9
9
1
11 7
12
REPAIR PARTS FOR MODEL 45-03732 SUN SHADE
REF.
NO.
PART
NO.
QTY. DESCRIPTION
1 66296 1 Base Bracket Assembly
2 25014 2 Upright Tube
3 25013 2 Top Tube
4 25012 1 U-Tube
5 25015 3 Support Rod
6 49609 1 Vinyl Canopy
7 26462 2 Support Bracket
8 43720 2 Plastic Knob
9 43081 6 Flat Washer, 5/16"
REF.
NO.
PART
NO.
QTY. DESCRIPTION
10 43648 4 Hex Bolt, 1/4-20 x 1-1/2"
11 47189 6 Nylock Nut, 1/4-20
12 43012 2 Hex Bolt, 1/4-20 x 3/4"
13 43063 4 Hex Bolt, 5/16-18 x 1"
14 44977 2 Carriage Bolt, 5/16-18 x 2"
15 47674 2 Plastic Cap
16 48661 4 Adhesive Pad
40921 1 Owner's Manual

the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com© 2017 Agri-Fab, Inc.