Agria 2200 HYDRO Use and care manual

Operating Instructions No. 998 417G B12.11
6083a
Before commissioning the machine, read operating
instructions and observe warnings and safety instructions.
&
Two-wheeled tractorTwo-wheeled tractor
Two-wheeled tractorTwo-wheeled tractor
Two-wheeled tractor
2200 Hydro2200 Hydro
2200 Hydro2200 Hydro
2200 Hydro
Hydrostatic tool carrier
Operating InstructionsOperating Instructions
Operating InstructionsOperating Instructions
Operating Instructions
Translation of the original operating instructionsTranslation of the original operating instructions
Translation of the original operating instructionsTranslation of the original operating instructions
Translation of the original operating instructions

2agria Two-wheeled tractor 2200 Hydro
Symbols, Name Plate
Please complete:
Machine Type No.: ......................
Identification No.:
....................................................
Engine Type: ...............................
Engine No.: .................................
Date of Purchase: .......................
For name plate, refer to p3/fig. A/8.
For engine type and number, refer to
p38/fig. B/17 and B/18.
Please state these data when order-
ing spare parts to avoid wrong deliv-
eries.
Only use original agria spare parts!
Specifications, figures and dimen-
sions stated in these instructions are
not binding. No claims can be derived
from them. We reserve the r ight for
improvements without changing
these instructions.
This delivery comprises:
l Operating instructions machine
l Operating instructions engine
l Two-wheeled tractor
l Tool kit
Symbols:
è- Serviceç
= contact your agria-workshop
see operating
instructions engine
Symbols
Warning – Danger
Caution
Important information
Fuel Choke
Engine StartEngine Stop
Engine Oil Engine oil level
Speed control
Air filter Air cooling
Clutch PTO
Wheel drive
Forward Reverse
Fast Slow
Brake Park brake
Open (unlocked)
Closed (locked)
Transmission Oil
Transmission oil level
Oiling Greasing point
Visual check
Wear protective gloves
Wear safety shoes
6Operating hours

agria Two-wheeled tractor 2200 Hydro 3
Designation of Parts
A
2
4
1
3
5
6
8
11
16
14
12 15
13
7
18
20
19
21

4agria Two-wheeled tractor 2200 Hydro
Designation of Parts
Fig. A
1Engine
2Cover/ Mudguard
3Hitch plate
4Equipment lock
5Drive wheel
6Belt guard
7Handlebar
8Name plate / machine identification no.
11 Clutch hand lever / Safety lever
12 Steering clutch lever left
13 Steering clutch lever right
14 P.T.O. shift rod
15 Speed control lever
16 Rotary handle for driving speed and travelling direction
18 Locking screw for steering handle height adjustment
19 Locking screw for steering handle lateral adjustment
20 Tool box
21 Engine shut-off switch

agria Two-wheeled tractor 2200 Hydro 5
Index
Amount of Delivery.......................... 2
Symbols, Name Plate ...................... 2
Designation
of Parts.............................. 3, 42
Recommendations
Lubricants, Anti-Corrosive Agents .. 6
Fuel .................................................. 6
Maintenance and Repair ................. 6
Unpacking and Assembly..... 7
1. Safety Instructions....... 8–12
2. Specifications
Two-wheeld tractor ......................... 13
Noise Level .................................... 13
Vibration Acceleration Value .......... 13
Engine ............................................ 14
Operation on Slopes ...................... 14
3. Devices and Operating
Elements
Engine ............................................ 15
Speed Control Lever ...................... 16
Engine Shut-off Switch .................. 16
Choke............................................. 16
Fuel Tap ......................................... 16
Clutch / Safety circuit .................... 17
P.T.O. Drive.................................... 17
Travelling Drive.............................. 18
Steering clutch ............................... 18
Coasting Operation ........................ 18
Steering Handle ............................. 19
Attachments ................................... 20
4. Commissioning and
Operation
Commissioning the Machine ......... 21
Starting the Engine ........................ 23
Shutting off the Engine .................. 24
Working .......................................... 25
Danger Zone .................................. 26
References, Handling ................... 27
5. Maintenance
Engine ............................................ 28
Cooling Screen .............................. 29
Cooling System ............................. 29
Governor ........................................ 29
Exhaust .......................................... 29
Speed Control ................................ 29
Machine ......................................... 30
P.T.O. Drive.................................... 30
Steering clutch ............................... 30
Drive-wheels .................................. 30
Clutch Hand Lever ......................... 31
Safety circuit .................................. 31
Steering clutch lever ...................... 32
General .......................................... 33
Cleaning ......................................... 33
Storage .......................................... 34
Varnishes,Wear Parts.......... 35
6.Troubleshooting........... 36-37
Electrical Wiring ................... 38
Lubrication Chart................. 39
Inspection and
Maintenance Chart............... 40
Conformity Declaration ....... 43
Note fold-out pages!
Fig. A ....................................... 3
Fig. B ..................................... 42
1
2
3
4
5
6

6agria Two-wheeled tractor 2200 Hydro
Recommendations
Lubricants and
Anti-Corrosive
Agents:
Use the lubricants speci-
fied for engine and gear-
box (see “Specifications”).
We recommend using
Bio-lubricating oil or
Bio-lubricating grease
for “open” lubrication
points or nipples (as
specified in the operating
instructions).
We recommend using
Bio-slushing oil to pre-
serve machines and at-
tachments (do not apply
on painted co vers). You
can brush or spray the oil.
Anti-corrosive agents are
environmentally friendly
and degrade fast.
Using ecologically saf e
Bio-lubricants and Bio-
anti-corrosives, you con-
tribute to environmental
protection and to the well-
being of humans, animals
and plants.
Fuel:
This engine runs perfectly
using commercially avail-
able lead-free Normal
and Super petrol (also
E10) as well as Super
plus.
Do not add oil to petrol.
If, for environmental rea-
sons, you use unleaded
petrol, make sure the fuel
is drained completely
when shutting do wn the
engine for more than 30
days. This is to pre vent
resin residue from depos-
iting in the caburetor, fuel
filter, and tank. Or add a
fuel stabilizer to the fuel.
For further instructions
see “Engine Preserva-
tion”.
Maintenance
and Repair:
The trained mechanics of
your agria workshop ex-
pertly carry out any main-
tenance and repair work.
You should only carry out
major maintenance work
and repairs on your own,
if you have the proper
tools and kno wledge of
machines and inter nal
combustion engines.
Do not hammer against
the flywheel with a hard
object or metal tools as it
might crack and shatter in
operation, causing inju-
ries and damage . Only
use suitable tools to pull
off the flywheel.

agria Two-wheeled tractor 2200 Hydro 7
Unpacking and Assembly
l Open the box top.
l Cut the two rear cor ners open and
fold down the side.
l Loosen the loc king screw (A/18)
until the catches are free
l Adjust the handlebar to the desired
height and bring it into the appropriate
tooth
l Tighten the locking screw (A/18).
l Carry out all steps for starting-
up (see instructions on page 21).
E
1Base machine
A/7 Steering handle
A/18 Locking screw for steering handle height adjustment
A/19 Locking screw for steering handle lateral adjustment
A/19
A/18
A/7
1

8agria Two-wheeled tractor 2200 Hydro
1. Safety Instructions
1
Before starting the engine, read the op-
erating instructions and note:
Warning
This symbol mar ks all par agraphs in
these operating instructions which af-
fect your safety. Pass all safety instruc-
tions on to other users and oper ators.
Due Use
The two-wheeled tractor is a hand-con-
trolled automatic single-axle machine
which can po wer various implements
approved by the manufacturer. The pri-
mary areas of use are f or mowing,
mulching, sweeping and snow clearance
(due use).
Any other type of oper ation is consid-
ered undue. The manufacturer is not li-
able for any damages resulting from
undue use, for which the r isk lies with
the user alone.
When the two-wheeled tractor is used
on public roads, the local national road
traffic rules must be observed, e.g. re-
flectors, lights.
The two-wheeled tractor is not intended
for use with a tr ailer on public roads or
as as a tractor unit without implements.
Due use includes compliance with
manufacturer’s instructions on oper a-
tion, maintenance and repair.
Any unauthorized changes to the ma-
chine render manufacturer liability null
and void.
General Instructions on
Safety and Accident
Prevention
Basic Rule:
The respective national accident pre-
vention regulations have to be adhered
to, as w ell as all other gener ally ac-
cepted rules governing operational
safety, occupational health and road traf-
fic regulations.
When driving on public roads, you have
to observe the current traffic code.
Accordingly, check the machine for road
and operational safety each time y ou
take up operation.
Only persons f amiliar with the tr actor
and instructed on the hazards of opera-
tion are allo wed to use , maintain and
repair the tractor.
Teenagers younger than 16 y ears are
not allowed to operate the machine!
Only work in good light and visibility.
Operator’s clothes should fit tight. Avoid
wearing loose fitting clothes. Wear solid
shoes.
Note the warning and instruction signs
on the tractor for safe operation. Com-
ply for your own safety.
When transporting the tractor on vehi-
cles or tr ailers outside the area to be
cultivated, ensure that the engine is
turned off.
Careful with rotating tools – k eep at a
safe distance!
Foreign powered parts shear and crush!
Riding on the attachment during opera-
tion is not permitted.

agria Two-wheeled tractor 2200 Hydro 9
1. Safety Instructions
1
Mounted or tr ailed attachments aff ect
the tractor’s driving, steering, braking,
and tipping char acteristics. Therefore,
ensure that steering and braking func-
tions are sufficient. Match operating
speed to conditions.
Do not change settings of governor. High
engine speed increases r isk of acci-
dents.
Working Area and
Dangerous Area
The user is liable to third par ties work-
ing within the tractor’s working range.
Staying in hazardous area is not per-
mitted.
Check the immediate surroundings of
the tractor before you start it. Watch out
for children and animals.
Before you start work, clear the area
from any foreign object. During opera-
tion, always watch out for further objects
and remove them in time.
For operation in enclosed areas, ensure
that a safety distance is k ept to enclo-
sures to prevent damage to tools.
Operation and
Safety Devices
Before you start the engine
Become familiar with the de vices and
operating elements and their functions.
Above all, learn how to turn the engine
off quickly and safely in an emergency.
Ensure that all guards in place.
With no attachment mounted, mak e
sure PTO-shaft is covered with the pro-
tective cap.
Starting the engine
Do not start the engine in closed rooms.
The carbon monoxide contained in the
exhaust fume is e xtremely toxic when
inhaled.
Before you start the engine set all con-
trols to neutral or idling position.
When starting the engine, do not step
in front of the machine and the attach-
ment.
Do not use assist-starting liquids when
using electrical assist-starting devices
(jumper cable). Danger of explosion.
Operation
Never leave the oper ator’s position at
the steering handle while tr actor is at
work.
Never adjust the handles during work -
danger!
For any operation do not leave the op-
erator’s position as defined by the steer-
ing handle, especially not when you turn
the machine.
Riding on the attachment during opera-
tion or in transport is not permitted.
If blockages occur in the attachment,
turn off the engine and clean the attach-
ment with an appropriate tool.
In case of damage to the tw o-wheeled
tractor or to the attachment, immediately
turn off the engine and have it repaired.
If steering causes problems, immedi-
ately bring the machine to a halt and
turn it off.
Have the malfunction remo ved without
delay.

10 agria Two-wheeled tractor 2200 Hydro
1. Safety Instructions
1
To prevent the machine from sliding on
slopes make sure it is secured b y an-
other person using a bar or a rope. This
person must be located at a higher po-
sition than the vehicle at a safe distance
from the attachment at w ork.
If possible, always work horizontally to
the slope.
End of Operation
Never leave the two-wheeled tractor
unattended with the engine running.
Before you leave the machine, turn off
the engine. Then close fuel taps.
Secure the machine against unauthor-
ized use. If tractor is equipped with an
ignition key, remove the key. For all other
versions, remove the spar k plug con-
nector to secure the tr actor.
Attachments
Only mount attachments with the engine
and PTO switched off.
Always use appropriate tools and wear
gloves when changing attachments and
parts thereof.
To fit and remove attachments, bring the
support leg into proper position and en-
sure stability.
Secure the machine and attachments
against rolling off (parking brake, wheel
chocks).
Beware of injuries while coupling attach-
ments.
Couple the attachments as specified
and only couple at specified points .
Secure the machine and attachment
against unauthorized use and rolling off
when you leave the machine. If neces-
sary, install transport or safety devices
to provide protection.
Hoeing Attachment
Adjust the guards in such a w ay that
only the sets of b lades penetrating the
soil are not covered.
When hoeing, make sure the depth bar
is adjusted properly.
Mowing Attachment
Handle with care! Shar p blades of the
cutter bar may cause injuries when han-
dled improperly! Remove knife guards
only for mowing and refit immediately
after work has finished.
For transport and storage always fit the
knife guards. Secure finger bars addi-
tionally with tension springs.
Do not transport the removed cutter bar
without knife guards.
When fitting/removing the cutter bar ,
make sure all b lades are protected b y
the knife guards.
To exchange the knife and to fit/remove
the knife driver, make sure that you turn
screws and bolts away from the cutting
blades to remove them.
To grind the mowing knives, always wear
safety goggles and gloves.
Weights
Always fit weights properly and at speci-
fied points.
Maintenance
Never carry out an y maintenance or
cleaning while the engine is r unning.
Before you work on the engine, always
remove spark plug connector (petrol
engine only).

agria Two-wheeled tractor 2200 Hydro 11
1. Safety Instructions
1
Check regularly and, if necessar y, re-
place all guards and tools subject to
wear and tear.
Replace damaged cutting tools.
Always wear safety gloves and use
proper tools when e xchanging cutting
tools.
Do not carr y out repairs lik e welding,
grinding, drilling, etc. on structural and
safety-relevant parts (e.g. coupling de-
vices)!
Keep the machine and the attachment
clean to avoid risk of fire.
Check nuts and bolts regularly for tight
fit and re-tighten, if necessar y.
Ensure that you re-install all safety and
guards and adjust them proper ly after
maintenance and cleaning.
Only use original agria spare parts. All
other conventional spare parts must cor-
respond to quality and technical require-
ments specified by agria.
Storage
It is not allowed to store the machine in
rooms with open heating.
Never park the machine in closed rooms
with fuel left in tank. Fuel vapours are
hazardous.
Engine,Fuel, and Oil
Never let the engine run in closed rooms.
Extreme danger of intoxication! For the
same reason, also replace damaged
exhaust pipes immediately.
Caution with hot engine par ts!
The exhaust and other engine par ts
become very hot, if the engine runs and
immediately after tur ning off. Hold f or
sufficient distance from hot surfaces and
keep children a way from the r unning
engine.
Be careful when dealing with fuel. Great
danger of fire! Never refill fuel close to
open fire, inflammable sparks or hot en-
gine parts. Do not refill fuel in closed
rooms. Do not smoke when refilling!
Refill only with the engine s witched off
and cooled down.
Do not spill any fuel, use a proper filling
device.
In case of fuel-spillage, pull the machine
away from the spillage before you start
the engine.
Make sure fuel is of specified quality.
Store fuel in approved cans only.
Store anti-corrosive agents and stabi-
lizing liquids out of reach of children. If
sickness and vomiting occur, see a doc-
tor. If fuel has contacted e yes, rinse
them thoroughly, avoid inhaling of v a-
pours.
Read and obser ve enclosed instr uc-
tions.
Before you dispose of opened and
seemingly empty pressurised tins (e.g.
of assist-starting liquids) make sure they
are completely empty. Empty them in
ventilated places safe from spar k for-
mation or flames. If necessary, dispose
of tins in hazardous waste deposits.
Be careful when dr aining hot oil, dan-
ger of burns.
Make sure oil used is of specified qual-
ity. Storage is in approved cans only.
Dispose of oil, g reases, and filters
seperately and properly.

12 agria Two-wheeled tractor 2200 Hydro
1. Safety Instructions
1
Tyres and Tyre Pressure
When working on the tyres , make
sure the machine is par ked prop-
erly and secured against rolling off.
Any repairs are to be carr ied out
by trained mechanics only and with
the appropriate tools.
Regularly check air pressure in the
tyres. Excessive pressure may
cause bursts.
When adding w eight, make sure
the tyre pressure is correct.
Re-tighten bolts of drive-wheels or
check tightness when doing main-
tenance work.
Electrical System
Persons having a pacemaker may
not touch live parts of the ignition
system when the engine is running.
Explanation of Signs
Warning Signs
Check engine oil level at least
every 8 hours.
When working with the ma-
chine, wear individual protec-
tive ear plugs.
Wear safety shoes.
Danger - flying objects; keep
distance from the machine as
long as the engine is running!
Stay clear of hot surf aces.
The exhaust fumes contain
breath poisons - k eep dis-
tance.
Do not start and operate
the engine in enclosed areas.
Warning: danger of fire - be-
fore each fuel fill, shut off the
engine and w ait until it has
cooled off - no open fire.
Before any cleaning, mainte-
nance, and repair work switch
off the engine and pull spar k
plug connector.

agria Two-wheeled tractor 2200 Hydro 13
2. Specifications
2
1
Dimensions:
a........................................ 350 mm
b........................................ 580 mm
c.........................................200 mm
d........................................ 800 mm
h............................. 800 - 1050 mm
l........................................ 1260 mm
A.................. (16x6.5-8) 670 mm
A....................... (4.00-8) 580 mm
Clutch:
V-belt clutch with idler pulley
between engine and gearbox
Only use original agria V-belts!
Driving gearbox: ............. Hydrostatic
................................ Agip SAE 10W40
.............. Filling quantity approx. 1,75 l
Travel speed steplessly:
Forward ............................... 0 - 7 km/h
Reverse ............................... 0 - 3 km/h
Steering clutch:.................both sides
............. sliding clutch and wheel lock
PTO shaft gearbox: .......... Gearwheel
.... Transmission oil Agip Blasia S 220
(Attention: synthetic oil, cannot be
mixed with mineral oil)
................ Filling quantity approx. 1,2 l
Steering handle:... vibration damping,
height-adjustable and
side-adjustable without tools
Weight:....................... approx. 105 kg
Noise level:
Noise level .................... Lp = 86.7 dBA
in accordance with EN 11201 (at
operator’s ear)
Acoustic power level LWA = 98.3 dB(A)
in accordance with EN ISO 3744
Vibration acceleration value:
on handlebar:................ ahw < 2.7 m/s2
in accordance with ISO 5349 at 85% of rated
engine speed with tool at work.
Tyres:..................................................
......................... 16x6.5-8 (Field tyre)
............... optional: 4.00-8 (Field tyre)
Tyre pressure: ........................ 1.0 bar
Two-wheeled tractor
agria 2200 Hydro

14 agria Two-wheeled tractor 2200 Hydro
2. Specifications
2
Engine
Manufacturer: ........................... Robin
Engine type: ........................... EX27D
Version: ....................... Fan-air cooled
1-cylinder, 4-stroke
petrol ohv engine
Bore: ........................................ 75 mm
Stroke: ..................................... 60 mm
Cubic capacity: ................... 265 ccm
Compression ratio:................. 8.5 : 1
Output: .............. 6.6 kW at 3,600 rpm
......................................... (9 SAE-PS)
Max. torque:.... 18.6 Nm at 2,500 rpm
Spark plug: .................. NGK BR-6HS
Spark plug gap: ............... 0.6–0.7 mm
Ignition system: ..... Magneto ignition
............................ transistor controlled
radio remote screened according to
VDE 0879
Valve lash (engine cold):
Intake: ................. 0.15 mm ± 0.02 mm
Outlet: ................. 0.20 mm ± 0.02 mm
Starter:
......................... Soft-pull recoil starter
........... with automatic decompression
Fuel tank capacity: .................... 6.1 l
Fuel: .......................... Unleaded petrol
......... octane number at least 91 RON
............................................ (also E10)
refer to fuel recommendations
Air filter: .................. Dry element filter
with foamed preliminary filter
Carburetor: ............... Float carburetor
Rated speed: ..................... 3,600 rpm
Top no-load speed: ........... 3,850 rpm
Idling speed:........... 1,250–1,600 rpm
Engine oil:
Filling quantity .................. approx. 1.0 l
Multi-grade oil SAE 10 W40
SG, SF or higher quality grade
Operability on Slopes:
Continuous operation possible
up to .................. 35° inclination (70 %)
Temporary operation possible
up to .................. 40° inclination (83 %)
(with oil level at “max” = upper level
mark)

agria Two-wheeled tractor 2200 Hydro 15
3. Devices and Operating Elements
3
The agria two-wheeled tractor type 2200
Hydro is a base power machine and is
always operated with an attachment
mounted. Therefore, the machine is
suited for horticultural, agricultural,
forestal operations, as well as for grass-
land and park maintenance and for win-
ter service work.
Available attachments are:
l mowing
l turf and grounds care
l sweeping
l gravel and salt spreading
l snow dozing and rotory snow
cleaning
Engine
The four-stroke petrol engine r uns on
conventional petrol (refer to fuel recom-
mendations p6). During the first 20 op-
erating hours (break-in per iod) do not
use engine to maxim um power. Even
after the break-in period never use
engine at higher speed than necessary
for the work in hand.
IHigh engine speed is harm-
ful to any engine and consid-
erably affects its longevity.This ap-
plies especiallyfor no load operation.
Any overspeed (have the engine roar)
can result in immediate damage.
Cooling System
The engine is f an-cooled. Therefore
keep screen at recoil star ter and cool-
ing fins of the cylinder clean and free
from sucked-in plant trash.
Idling Speed
Always ensure that idling speed is ad-
justed correctly. At low speeds and with
the speed control le ver set to idle , the
engine is supposed to run smoothly and
without run-out.
Air Filter
The air filter pur ifies the air intak e. A
blocked filter reduces engine output.
Ignition System
The engine is equipped with a mainte-
nance-free, contactless electronic igni-
tion system.
We recommend to ha ve necessary
check-ups done by an expert only.
IPlease note that only the information on the engine is explained
here which is necessary for the operation of the two-wheeled
tractor.
All other information about the engine may be obtained from the
attached engine operating instructions.

16 agria Two-wheeled tractor 2200 Hydro
3. Devices and Operating Elements
3
Speed Control Lever
The speed control lever (A/15) on the steering han-
dle is f or stepless setting of engine speed from
min. = idle to max. = full throttle.
Engine Shut-off Switch
On pressing the switch (A/21), the ignition is turned
on or off.
Position “O” = Engine off
Position “I” = Operation
IThe engine shut-off s witch also
serves as an emergency shut-off.Set the
switch to “O” for fast shut-off.
Choke
The choke lever (B/10) is on the carburetor.
l Close the choke for cold starts. To do this, move
the lever to the left.
l Open the chok e for warm starts and oper a-
tion. To do this, move the lever to the right.
Fuel tap
The fuel tap (B/11) is on the carb uretor.
l Fuel tap lever turned downwards
- O (OPEN)
l Fuel tap lever turned to the right
- I (CLOSED)
max
min
A/21
A/15
O
I

agria Two-wheeled tractor 2200 Hydro 17
3. Devices and Operating Elements
3
Clutch / Safety Circuit
The two-wheeled tractor is equipped with a V-belt
clutch. Operation is via the clutch lever (A/11).
l If the clutch lever is pressed down (position I), a
power connection is created betw een the engine
and both the PTO shaft and the hydrostatic gear-
box.
l If the clutch le ver is not oper ated (position O)
the clutch is disengaged, i. e. the engine does not
drive the PTO shaft and the hydrostatic gearbox.
l The clutch lever is at the same time a saf ety
control which must be operated in two stages:
1. Pull the locking catch (unlatching)
2. Press the clutch lever downwards.
P.T.O.Drive
The drive for attachments is made through the PTO
shaft and a connecting flange .
The PTO shaft is switched on and off with the ac-
tuating lever.
Switching on:
Push the PTO actuating lever (A/14) up and back-
wards up to the stop
W - when doing this place your thumb on
the side of the lever (danger of crushing).
Switching off:
Push the PTO actuating lever down and forwards.
IOnly switch the PTO actuating lever on
and off when the clutch lever is not being
operated!
O
I
A/14
1. 2.
A/11
O
I

18 agria Two-wheeled tractor 2200 Hydro
3. Devices and Operating Elements
3
Travelling Drive
l By turning the handle (A/16) in a clockwise di-
rection the machine moves forwards with increas-
ing speed up to a maxim um of 7 km/h
l By tur ning the handle (A/16) in an anticloc k-
wise direction the machine moves backwards with
increasing speed up to a maximum of 3 km/h
l Central position = Neutral (catch)
Steering clutch
The easy-to-operate steering clutch units enab le
steering and turning without exertion.
In order to steer and turn to the right pull the lever
(A/13) . The right driving wheel is disengaged,
stopped and the machine is steered when dr iving
to the right.
Zn order to steer and turn to the left pull the lever
(A/12).
Lever positions:
Driving wheel disengaged
Driving wheel disengaged, retaining pawl (3)
can be snapped into place
Driving wheel is stopped
WOnly turn on the incline on embankments.
Coasting Operation
The machine can be pushed when the engine is
not in operation if both dr iving wheels are disen-
gaged using the steeering clutch lever
l pull both levers and latch the pawls (3) into
place.
A/16
A/13A/12
3
STOPP

agria Two-wheeled tractor 2200 Hydro 19
3. Devices and Operating Elements
Steering Handle
Steering handle height adjustment
l Open locking screw (A/18) until all notches are
free.
l Swivel the steering handle to the desired height
and fit into proper notch.
l Re-tighten locking screw (A/18).
Steering handle side adjustment
l Loosen locking screw (A/19) until all notches
are free.
l Swivel the steering handle to the desired posi-
tion and fit into proper notch.
l Re-tighten locking screw (A/19).
A/18
A/19
3

20 agria Two-wheeled tractor 2200 Hydro
3
3. Devices and Operating Elements
Attachments
WOnly couple and decouple at-
tachments when the engine is
stopped. Secure attachments against roll-
ing off.Watch out to avoid getting bruised
when coupling the attachment.
The attachments are connected and discon-
nected using the attachment quick-connection
coupling without the need for any tools.
The latch for the attachment connection cou-
pling is at the front on the attachment mount-
ing.
Connecting attachments:
l The attachment mounting on the main de-
vice and the connecting por t on the attach-
ment device must be clean.
l Lightly grease the connecting por t
l Switch PTO shaft drive to "O"
l Pull the locking bolt (A/4) upwards and turn
by 90°
= Lock open
l Remove the protective cap from the con-
necting port of the attachment
l Insert the attachment into the mounting
l Turn the locking bolt by 90° so that it can mo ve
downwards and lock independently into place
= Lock closed, if not: turn the device a little
to the left or to the r ight.
Disconnecting attachments:
l Pull the locking bolt (A/4) upwards and turn
by 90°
= Lock open
l Pull the attachment out of the mounting
l Place the protective cap onto the connect-
ing port of the attachment.
èO
A/3
A/4