Agua TITAN User manual







Before using this product. Please read the following
instructions carefully and keep this brochure for
future reference.
2

Tear the paster on back of hanger.
Install battery and place remote
control to the hanger.
Insert expansion tube into the hole on
the wall, install the hanger to the wall
with a screw, and paste the double
faced adhesive tape on hanger to the
wall, tighten the screw.
Notice：Please do not install and use the product in moist place, such as steam
room, and prohibit to place in the space where is easily got wet.
STOP
NOZZLE
CLEANING
REAR FRONT DRY
MASSAGE
USER 1 USER 2
WATER
DRY SEAT
PRESSURE
POSITION
ENERGY
SAVER
3

1Drill a hole of 6mm on the wall with
depth of 35mm. Make sure end-user
be able to reach the remote control
when sitting on the seat.
2
34


DRY SEAT
STOP
NOZZLE
CLEANING
FLUSH
REAR FRONT DRY
MASSAGE
Massage
Drying
Front cleaning
Rear cleaning
Stop
Water pressure
Dry temperature
Energy saver
Water temperature
Flush button
Spray nozzle position
Seat temperature
Nozzle cleaning
Instruction signal
User code 2
USER 1 USER 2
ENERGY SAVER 3 6 9 H
PRESSURE POSITION
PRESSURE POSITION
WATER DRY SEAT
ENERGY
SAVER
WATER
User code 1
4

Dry
Front
Rear
REAR FRONT DRY
DRY SEAT
ENERGY SAVER 3 6 9 H
PRESSURE POSITION
WATER
Massage
PRESSURE
PRESSURE
PRESSURE
MASSAGE
POSITION
Nozzle
DRY SEAT
ENERGY SAVER 3 6 9 H
PRESSURE POSITION
WATER

Press “REAR”/“FRONT ” button, the water comes
out of wand to clean the rear/front portion of the
body. It automatically stops after a cycle of cleaning.
If you press “STOP” button when using, the function
will stop immediately.
Rear/Front cleaning
Press “DRY” button, warm wind comes out of wand to
dry. After a cycle or user leaves the seat, it
automatically stops.
Drying Operation
Press “MASSAGE” button to activate massage
function, the nozzle moves forward and back to
extend the cleaning scope; Press “MASSAGE”
button again to stop the function.
Massage
During “REAR” or “FRONT”, press spray nozzle
button of “ ” and “ ”, to move the position
forward and backward by adjusting 5 levels.
Spray nozzle position adjustment
During “REAR” or “FRONT”, press water pressure
button of “+” and “-”, to adjust pressure for rear
and front cleaning.
Water pressure adjustment
5

Water temperature adjustment:
Press“WATER” button to adjust temperature for rear and
front cleaning. The LCD display of 1 to 5 lines means level
1 to 5.NO display means normal temperature.To adjust
level by up and down cycle.
Dry temperature adjustment:
Press “DRY”button to adjust temperature for drying.
The LCD display of 1 to 5 lines means level 1 to 5.NO display
means normal temperature.To adjust level by up and down
cycle.
Seat temperature adjustment:
Press “SEAT”button to adjust temperature of seat. The LCD
display of 1 to 5 lines means level 1 to 5.NO display means
normal temperature. To adjust level by up and down
cycle.
DRY
DRY
DRY
WATER
SEAT
ENERGY SAVER 3 6 9 H
ENERGY SAVER 3 6 9 H
ENERGY SAVER 3 6 9 H
ENERGY SAVER 3 6 9 H
WATERDRY SEAT
PRESSURE POSITION
WATER SEAT
WATER
SEAT

6

Setting energy saver time
Press “ENERGY SAVER” button, LCD screen shows energy saver and figures. It shows three options of energy
saver period as 3-6-9-off, which can be selected accordingly. For example, user can set from 9:00 to 15:00 as
energy saver according to following operation.
Press“ENERGY SAVER”button, LCD screen shows “ENERGY SAVER” icon.
Press“ENERGY SAVER”button again, LCD screen shows figure “6”, and the “ENERGY SAVER”icon disap-
pear after 3 seconds, the setting succeeds. The toilet enters the energy saver mode from 9:00 to 15:00
every day. During this period, power light is off, and the energy saver light is on. It goes back to normal
operation mode after energy saver time.
Remark :
If the user sits on the seat, the energy saver mode is paused, and enters into the function mode, the
seat starts to heat immediately (under opening seat temperature circumstances). The energy saver mode
restores after user leaves. When the energy saver mode is set, the icon disappears automatically, which is a
normal set.
Cancel energy saver set: Press“ENERGY SAVER”button continuously until this function is cancelled. (Nothing
display on the screen.)The toilet will be under energy saver mode automatically after setting. Under energy
saver mode, seat temperature is on low temperature status (first level) to achieve energy saver.
energy saver icon
ENERGY SAVER 3 H
ENERGY
SAVER
DRY SEAT
PRESSURE POSITION
WATER

1
2
3
7
9:00 15:00
The toilet enters the energy saver
mode from 9:00 to 15:00.
Energy saver light is on
Energy saver time
ENERGY SAVER 6 H
ENERGY SAVER
POWER
DRY SEAT
PRESSURE POSITION
WATER

8
Nozzle cleaning
Nozzle self-cleaning by quick press：
Quick press “NOZZLE CLEANING”
button, the nozzle self-cleans for a while
and move to the front position (no
spray). People can continue to clean
nozzle manually.
NOZZLE
CLEANING
self-clean for
90 seconds.
Nozzle self-cleaning by long
press：
Long press “NOZZLE CLEA-
NING” button, the spray won’t
move forward and nozzle
self-cleans for 90 seconds.
User settings
Long press “USER 1” or “USER 2”button to save the parameters, including current pressure, nozzle position,
dry temperature, water temperature, seat temperature and massage status. Quick press “USER 1” or “USER
2” button to use saved parameter.
DRY
USER 1 USER 2 USER 1 USER 2
ENERGY SAVER 3 6 9 H
PRESSURE POSITION
WATER SEAT
Settings user 1 Settings user 2


Night light
Press “STOP” button, then “DRY” button, night light will often be in the off state; Repeat the process, night
light will switch to intelligent state. Repeat above process constantly, the night light will switch between off
state and intelligent state.
Quiet mode
Press “STOP” button and then “MASSAGE” button to turn off the buzzer to avoid noise in the night; Repeat the
process to start buzzer function.
User code
The user code needs to be set to avoid disturbance from remote controls when more than one toilets are used
in the house.Turn on the toilet for setting while turn off others. (1) Press“STOP”button and then“REAR” button
to enter into user code setting. The remote control shows only water pressure and spray position level,and
characters are blinking on the screen. (2) Press water pressure buttons of “+”and “-”,to choose user code 1-9.
(3) Press“STOP”button and then“REAR” button again,remote control will save the setting and exit user code
setting windows,the buzzer will ring “click” to indicate successful setting. The sum of water pressure and
position level on LCD is the user code.Restart to clear the user code and re-set.
Remark:
In case of power cut during wand’s spray operation, the wand cannot go back to place,please wait until the
power is reset. In case of a power cut for a long period, please push the wand softly back by hand. Do not
push hard, to avoid damage to wand and electrical machine.

9