Aiphone LEM-1DL/C User manual

®AIPHONE
LEM-1 DLC
Multi-Master Access Sentry System
Master Station for Multiple Master Use, including Occupied Lamp
I and understand all 1 - INSTRUCTIONS -
Master #1 Master #2
OPERATION NOTES:
1. Only one master can be used at a time.
2. When the answering master presses the TALK button, the red LED above the OFF switch wiii iight on both masters.
This feature is controlled by the "R" wire between masters.
3. When the OCCUPiED iight is iiiuminated, do not press the TALK button on the non-answering master, or a feedback
wiii be heard throughout the system, if this occurs, turn off one of the masters (depress OFF button). At that time,
communication between the door and the answering master can continue normaily.
4. There is no communication between masters.
iNSTALLATiON GUIDELiNES:
1. Separate power supplies (12-16V AC or 12-24V DC) are required at each master station.
DO NOT CONNECT +/- WIRES BETWEEN MASTERS. Keep wires for power and communication in separate jackets.
2. The door strike can be powered from one of these power sources (as shown) or from an independent source. Door
release contact rating on the LEM-1 DLC is 24V DC, 1A max.
3. The EL-9S is designed for a standard wood framed door, and for light to medium usage. If a different type of door is
used, install a strike appropriate for that door.
4. The LEM-1 DLC provides a "normally open" contact closure for door release.
5. If using a magnetic lock, either the RY-18L or RY-24L relay will be required to get a normally closed contact.
(See diagram on back)
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
[phone]
FAX [phone]
TOLL FREE TECHNICAL SUPPORT:
[phone]
TOLL FREE FAX LINE:
[phone]
E-MAIL: [email protected]

Specifications and Dimensions
©Copyright, >
or TRANSMIT

Warnings
The product is intended to assist in safe driving and to allow the driver to
have a broader rear view while the vehicle is in reverse. You, as the
driver, are solely responsible for the safe operation of your vehicle and
the safety of your passengers according to local traffic regulations. Do not
use any features of this system to the extent it distracts you from safe
driving. Your first priority while driving should always be the safe
operation of your vehicle. Audiovox Electronics Corporation cannot
accept any responsibility whatsoever for accidents resulting from failure
to observe these precautions or safety instructions.
1. This product utilizes high voltage. Any unauthorized modifications or
damage to the product may result in electrical shock. Handle all
components with care. Inspect regularly for damage to components
and cabling.
2. You are responsible for ensuring that the installation of this product
does not void or affect the vehicle manufacturer’s warranty.
Audiovox Electronics Corporation or its subsidiaries are not liable in
full or in part for improper installation resulting in loss or damage to
your property, or for voiding all or part of the vehicle manufacturer’s
warranty.
3. Do not apply excessive force to any of the components contained
within this kit. Excessive force used before, during or after
installation that results in a damaged or non-functional part will void
all warranties.
4. Please follow the procedures in this installation manual. Improper
installation or modification of this product will void all warranties.
3

Introduction
Product Features
This product is an SVGA single chip 0.55" DTP ™ p rojector. Its outstanding
features include:
♦ True SVGA, 800 x 600 addressable pixels
^ 4.5 lbs (2 kgs) compact design
♦ Single chip DLP ™ technology
^ Independent white-balance adjustment, for natural picture quality
O Digital zoom features
♦ PureProgressive ™ processing technology for artifact-free film materials
♦ Full HDTV compatibility (480i/p, 10801, 720p)
NTSC/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and HDTV compatible
♦ Fully functioning remote with optional mouse control
♦ User-friendly multilingual on screen display menu
T Advanced electronic keystone correction and high quality full digital functionality
♦ User-friendly control panel
♦ Luxurious carrying bag included
When set to the smallest ratio, the projector can support up to SXGA and can fully
support VGA and SVGA
150 watt user replaceable lamp
♦ Compatible with Apple Macintosh

ProJet® x60Pra Series User Guide
3
4
5
6
Routine Cleaning.
3.1 Vacuum Excess Core.
3.2 Ciean The Debris Separator.
3.3 Ciean The Parking Caps.
3.4 Clean The Fast Axis Rails and Carriage....
3.5 Clean The Service Station.
3.5.1 Example - Dirty Service Station.
3.5.2 Example - Clean Service Station.
3.5.3 Cleaning Procedure.
Post-Processing.
4.1 Post-Processing Using Water Cure.
4.2 Post-Processing With ColorBond ™ .
4.3 Post-Processing With StrengthMax ™ .
Additionai Operations.
5.1 The Printer Status Dialog.
5.1.1 Ready to Print.
5.1.2 Not Ready to Print .
5.2 Change Print Head(s).
5.3 Add Binder.
5.4 Adding Core to the Feeder.
5.5 Add Cleaning Solution.
5.6 Replace the Waste Tray.
5.7 Position Build Piston (Build Bed).
5.8 Cover.
Printer Maintenance.
6.1 Fast Axis Bearing Lubrication.
6.2 Piston Screw Lubrication - ProJet 660Pro.
6.3 Piston Screw Lubrication - ProJet 860Pro.
6.4 Slow Axis Bearing Lubrication.
6.5 Clean The Alignment Sensor Window.
6.6 Clean The Fast Axis Pulleys.
6.7 Clean The Slow Axis Rails and Pulleys.
6.8 Clean The Spreader Roller.
6.9 Printer Storage Preparation.
26
26
26
28
31
36
36
. . 36
.38
. . 38
40
43
45
45
46
47
7 Troubieshooting the ProJet x60Pro.61
7.1 Try This First. 62
7.2 Problems Powering Up. 63
7.3 Print Head Errors/ Weak Parts. 64
7.3.1 Try This First. 64
7.4 Alignment Errors. 66
7.5 Motion Errors - Fast Axis. 67
7.6 Motion Errors - Slow Axis. 69
7.7 Network Errors - Cannot Connect to Printer. 71
7.8 Network Errors - Packet Timeout. 72
7.9 Part Quality Issues - General. 72
All Rights Reserved
5/12/13

Audio to Hi-fi System (Digital)
Audio vers chaTne haute fidelite (Numerique)
Audio al sistema Hi-fi (Digital)
U
PC connects to TV (as PC monitor)
L’ordinateur se connecte sur un televiseur
(en tant que moniteur d’ordinateur)
El computador (PC) se conecta al televisor
(como monitor del computador).
TV Jack Panel
Control remoto Boton Source

Enter Password: In order to configure another adapter remotely, you’ll need to enter its
physical password first. Select the desired adapter from the list and click on the Enter
Password button.
The adapter’s password is printed on the back label.
Once the password is successfully entered, it will appear in the device list.

User’s Manual
Power on/off your photo frame
To power on the photo frame, please press the Power button for 2
seconds. To power off the photo frame, please press the Power
Charging the battery
Plug the AC power adapter into the DC-IN jack of the device, and connect the other
end to the power source.
Connect the small end of the supplied USB cable to the USB port of the device, and
the large end to a powered PC. Make sure the photo frame is powered off.
Charging Status
Power OFF, charging by AC power adapter
Charging Time
around 2 hours
Power OFF, charging by USB connection around 12 hours
Pag<

Lsnguage Selection 9
Follow the steps below to change the language ol the on-screen
displays and menus.
1
Pressthe COMBI button, then pressthe MENU button.
2
Pressthe PLAY/A button or the STOP/T button to select
PRIM. SETUP. Then, pressthe F.FWD/P> button.
Pressthe PLAY/A button or the STOP/T button to
choose SELECT LANGUAGE. Then, pressthe F.FWD/P>
button.
4
Pressthe PLAY/A button or the STOP/T button to select
ENGLISH or ESPANOL (Spanish).
5
5 2-4
Helpful Hint
• If you accidentally select Spanish
and need
English on-screen displays
and mem
tj Press I
he COMBI button, then
MENU button.
2) Press t
STOP/f button to select PREPARA-
CION, th( ;n press the F.FWD/^
button.
3) Press I
he PLAY/^ button or the
STOP/f button to seleot SELEC-
CION IDIOM A, then press the
F.FWD*-button.
4) Press t
he PLAY/A. button or the
STOP/f
button to seleot ENGLISH.
5) Press I
he STATUS/EXIT button.

^
I