Aiphone GT-TLI User manual

GT-TLI
Installation / Operation Instructions
This is the installation and operation manual for the GT-TLI only. Refer to the GT Series Installation
and Operation Manual for complete information on all other GT components.
1012
Telephone Line Interface for the GT Series
ATTENTION:

Precautions
! WARNING
(Negligence could result in death or serious injury to people.)
2 | GT-TLI Installation / Operation Instructions
• High voltage is present internally. Do not open the case. Electric shock may occur.
• Do not dismantle or alter the unit. Fire or electric shock may occur.
• Donotconnectanynon-speciedpowersourcetothe+,-terminalsanddonotinstalltwopowersuppliesin
paralleltoasingleinput.Fire,damagetotheunit,orsystemmalfunctionmayoccur.
• Keeptheunitawayfromwateroranyotherliquid.Fireorelectricshockmayoccur.
• Do not put any metal or paper into the unit through the openings. Fire of electric shock may occur.
• Donotplugorunplugwithwethands.Electricshockmayoccur.
• KeepACplugawayfrommoistureordustasremayoccur.
• KeepACcordfrombeingmarredorcrushed.IftheACcordisdamaged,reorelectricshockcouldoccur.
• Donotuseapowersupplywithavoltageotherthanspecied.Fireorelectricshockmayoccur.
• InsertACplugcompletelyandsecurelyintoACoutlet.Otherwise,reorelectricshockmayoccur.
• Donotinstalloruseneargasesorammablematerials.Fireorexplosionmayoccur.
! CAUTION
(Negligence could result in injury to people or damage to property.)
• Beforeturningonpower,makesurewiresarenotcrossedorshorted.Fireorelectricshockmayoccur.
• Whenmountingtheunitonwall,installtheunitinaconvenientlocation,butnotwhereitcouldbejarred
orbumped.Injurymayoccur.
• Donotinstallormakeanywireterminationswhilepowersupplyispluggedin.Itcouldresultinelectricshock
or damage to the unit.
• Donotinstalltheunitinanyofthefollowinglocations.Fire,electricshock,orunittroublemayoccur.
-Placesunderdirectsunlight,ornearheatingequipmentthatvariesintemperature.
-Placessubjecttodust,oil,chemicals,hydrogensulde(hotspring).
-Placessubjecttomoistureandhumidityextremes,suchasbathrooms,cellars,greenhouses,etc.
-Placeswheretemperatureisquitelow,suchasinsidearefrigeratedareaorinfrontofanairconditioner.
-Placessubjecttosteamorsmoke(nearheatingorcookingsurfaces).
-Placeswherenoisegeneratingdevicessuchasdimmerswitchesorinvertorelectricalappliances,areclose.
• Onproductswithgroundterminals,connecttoanearthground.Fireormalfunctionmayoccurifunitisnot
properly grounded.
• ForDCpowersystems,useAiphonepowersupplymodelspeciedwiththesystem.Ifnon-speciedproductis
used,reormalfunctionmayoccur.
• Do not place anything on top of unit. Fire or unit malfunction may occur.
• Donotmounttheunitinaplacesubjectedtoconstantvibrationorimpact.Ifjarredorknockedoffthewall,
injurymayoccur.
GENERAL PRECAUTIONS
• Allunits,exceptforthedoorstation,aredesignedforindooruseonly.Donotuseoutdoors.
• Inareaswherebroadcastingstationantennasarecloseby,theintercomsystemmaybeaffected
byradiofrequencyinterference.
• Ifacellularphoneisusedcloseby,theunitmaymalfunction.
• Thisproduct,beingacontrolunitfordoorrelease,shouldnotbeusedasacrimepreventiondevice.
• Keeptheunitmorethan3feetawayfromradioorTVset.
• Duetotheenvironmentalsoundaroundtheunit,itmayhindersmoothcommunication.Thisisnotamalfunction.

• Installation / Operation Instructions
• GT-TLI
• RJ11 cable
Wiring
Installation
AworkingGTsystemwithatleastoneentrypanelisrequiredwhenusingtheGT-TLItelephonelineinterfaceadaptor.
TheGT-TLIcanbedeskmountedorwallmountedusingthemountingslotsonthebackoftheunit.Ensurethatthe
mounting location is accessible.
3
Package Contents
R2
R1
NO C NC R1 R2CO TEL 12-24V
+
-
12-24VAC/DC
GT Bus Line
To Local Telephone
From Phone Line
GT-TLI
EL-12S
13 /16"
3-9/16"
1-1/8"
Secondary Dry Contact
PT
Specications
COLINE: Totelephoneline(RJ11)
TEL:  ToInternalhousetelephone(RJ11)
12-24VAC/DC:Topowersupply12VAC/DC-0.5A,24VAC/DC-0.3A
R1/R2: To R1/R2 audio bus of GT system
NO/C/NC: 12VDC-2A,24VDC-1A

4 | GT-TLI Installation / Operation Instructions
Below are a few examples of connecting the GT-TLI to an existing telephone installation.
Wiring (continued)
Basic Connection
CO TEL
From Phone Line
CO TEL
CO TEL
PBX
Analog Port
CO Line
SETTING
1
4
GHI
7
PQRS
#0
ABC
JKL
TUV
5
8
2
6
9
WXYZ
MNO
3
DEF
TRANSFERPRIVACY HOLDSETTING
1
4
GHI
7
PQRS
#0
ABC
JKL
TUV
5
8
2
6
9
WXYZ
MNO
3
DEF
TRANSFERPRIVACY HOLDSETTING
1
4
GHI
7
PQRS
#0
ABC
JKL
TUV
5
8
2
6
9
WXYZ
MNO
3
DEF
TRANSFERPRIVACY HOLD
Note:
GT-TLI supports a maximum
of 3 telephone sets.
PBX Connection
3 Telephone Connection
From Phone Line

Linking GT-TLI to GT system
Direct Select / Push Button Entrance Station Addressing
Step 1:
Remove front cover from entrance station.
Step 2:
 Toenterprogrammingmode,useasmallscrewdrivertopushandreleasebuttonundertherubbercaponfront
ofspeakermodule(GT-DA-L).TheamberLEDwillbeginashing,thenremainlit.Oncelit,theentrypanelisin
programming mode.
Step 3:
 AtGT-TLI,pressthePROGbutton.TheGT-TLIisnowconnectedtotheentrancepanel.
Step 4:
Push and release the desired Call Button on the entrance station to assign the button to the GT-TLI station that is
active.Abliptonewillbeplayed.
Step 5:
 AtGT-TLI,pressthePROG button to complete programming.
Step 6:
 Toexitprogramming,pushthebuttonundertherubbercapontheGT-DA-LmoduleagainandtheamberLEDwill
turnoff.Thesystemisnowreadyforuse.
GT Digital Display Entrance Station Addressing
Step 1:
Remove front cover from entrance station.
Step 2:
 Toenterprogramming,useasmallscrewdrivertopushandreleasebuttonundertherubbercaponfrontof
speakermodule(GT-DA-L).TheamberLEDwillbeginashing,thenremainlit.Oncelit,theentrancestationisin
programmingmode.TheLCDwillshow“CONNECTING”whileinprogrammingmode.
Step 3:
 AtGT-TLI,pressthePROGbutton.TheGT-TLIisnowconnectedtotheentrancepanel.
Step 4:
Scroll to the station number to be programmed or manually dial the number. When the tenant station number is
displayed,pushandreleasetheBell button
to assign the address to the GT-TLI station that is active. A blip tone
willbeplayed.
Step 5:
 AtGT-TLI,pressthePROG button to complete programming.
Step 6:
 Toexitprogramming,pushthebuttonundertherubbercapontheGT-DA-LmoduleagainandtheamberLEDwill
turnoff.Thesystemisnowreadyforuse.
DO NOT press and hold the Call Button as doing so will clear the memory for this button.
5
NAMES
DO NOT press and hold the Call Button as doing so will clear the memory for this button.
PowerLEDIndicator
Unitisonwhenlit.
POWER: Master power switch
(ON/OFF)
PROG: Press to link GT-TLI to
system (in program mode)
3 Position Switch
OFF: Disables GT-TLI’s dial out function
ON: Enables GT-TLI’s dial out function
LOCAL PROG: Programming by using direct
connected telephone

6 | GT-TLI Installation / Operation Instructions
SET UP
Linking GT-TLI to GT system (continued)
TheGT-TLIcanbeprogrammedeitherwiththelocal(internal)telephoneorremotelybycallingin,viaDTMF.
(seeowchartbelow)
EnterPassword
2000# or 2001#
Enter programming
• telephone #
• time outs
• audio levels
• etc...
Enter00toexit
programming
GT-DM Entrance Station Addressing
Step 1: Whileinstandbymode,enter#plusIDcode(defaultis  1111).Re-enterIDcode.
Step 2: Usetheup/downarrowsandscrollto
PROGRAMMING
. Push the Bell button to enter programming mode.
TheamberLEDwillbeginashing,thenremainlit.Oncelit,theentrypanelisinprogrammingmode.TheLCDwill
show“CONNECTING”whileinprogrammingmode.
Step 3: AtGT-TLI,pressthePROGbutton.TheGT-TLIisnowconnectedtotheentrancepanel.
Step 4: Scroll to the station number to be programmed or manually dial the number. When the tenant station number is
displayed,pushandreleasetheBell button to assign the address to the GT-TLI station that is active. A blip tone
willbeplayed.
Step 5: AtGT-TLI,pressthePROG button to complete programming.
Step 6: Toexitprogramming,pressthe“X”buttononthepaneltoreturntothemainmenu(theamberLEDwillturnoff).
Scroll to
QUIT
andpressthe“X”buttonagain.Thesystemisnowreadyforuse.
DO NOT press and hold the Call Button as doing so will clear the memory for this entry.
Select“LOCALPROG”
on GT-TLI
Pick up local telephone
and dial code
Local Telephone
Dial phone #
of GT-TLI
Remote Telephone

SET UP - Accessing Program Mode
7
Note:
• A maximum of 10 seconds are allowed for each programming input. If the time exceeds 10 seconds,
the GT-TLI returns to standby mode.
• No programming entries are possible when the GT-TLI is playing indicator sounds.
• Entering a correct function code is indicated by 1 long beep.
• Correct entry of parameters are indicated by the message “The code entered is correct”
(see Programming Summary Chart).
• Incorrect entry of parameters are indicated by 2 long beeps, or by the automated message
“The code entered is incorrect”. The GT-TLI will wait for a new function number.
Remote programming via DTMF telephone
• DialthetelephonenumberoftheGT-TLI(tenant’sphonenumber).
• Anautomatedmessagewillplay“Callfromdoorpanel.”
• Dialoneofthetwofollowingprogramaccesscodes;2000# or 2001#.
2000#=generalparameters(volumelevels,timing,etc.)
2001#=controlledparameters(callingtelephone#,etc.)
• Anautomatedmessagewillplay“Thecodeenterediscorrect.”
• Makeprogrammingchanges(seenextpage).
• Whenprogrammingiscomplete,dial00toexit.
• “Thecodeenterediscorrect”willbeplayedandtheGT-TLIwillgointoidlemode.
Local programming via telephone connected directly to GT-TLI
• Flipthe3positionswitchontheGT-TLItoLOCAL PROG.
• Activate handset on connected telephone.
• Dialoneofthetwofollowingprogramaccesscodes;2000# or 2001#.
2000#=generalparameters(volumelevels,timing,etc.)
2001#=controlledparameters(callingtelephone#,etc.)
• Anautomatedmessagewillplay“Thecodeenterediscorrect.”
• Makeprogrammingchanges(seenextpage).
• Whenprogrammingiscomplete,dial00toexit.
• “Thecodeenterediscorrect”willbeplayedandtheGT-TLIwillgointoidlemode.
• Hanguphandsetandreturnthe3positionswitchtoONposition.

SET UP - Basic Programming
Thefollowing6programmingstepsmustbedonepriortooperatingtheGT-TLI.
Disabling / Enabling Door Calling Telephone
TheGT-TLIcanbedisabledfromcallingtheprogrammedtelephone,incaseswherethetenantwishesnottobe
disturbedbytheGTentrancepanel.ThedefaultsettingiswithDoorCallActivationenabled.
• Enter program access code 2001# -“Thecodeenterediscorrect”willbeplayed
• Enter toenable,or# to disable
• “Thecodeenterediscorrect”willbeplayed,andtheGT-TLIwillgointoidlemode
Ring Duration of Locally Connected Telephone
Settheringdurationfortheconnectedtelephone(s).Timesetmustbebetween10-45seconds.
• Enter program access code 2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 20-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=timeinseconds,i.e.30)
Program Remote Call Number
SettheremotetelephonenumberthatwillbedialedbytheGT-TLI.Thetelephonenumbercanbeupto16digitslong.
Ifthetelephonenumberislessthan16digits,press#afterthelastdigit.A"“canbeusedwhenapauseisrequired.
Forexample,ifneedingtodialadigitpriortoaccessinganoutsidephoneline,orifdialingaphonenumberwithan
extension,usethe““forapause.
• Enter program access code 2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 21-1longbeepwillbeplayed
• Enter nn #-“Thecodeenterediscorrect”willbeplayed(nn=telephonenumber)
To delete a telephone number.
• Enter program access code 2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 21-1longbeepwillbeplayed
• Enter #-“Thecodeenterediscorrect”willbeplayed
Program DTMF Code for GT Entrance Panel
InorderforthetelephonetoactivatethedoorreleasecontactontheGTentrancepanel,a2-digitaccesscodemust
beenteredonthetelephonewhileincommunicationwiththedoorstation.Thedefaultcodeis10.
• Enter program access code 2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 25-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=2digitaccesscode)
Program DTMF Code for GT-TLI Secondary Dry Contact
InorderforthetelephonetoactivatethesecondarydrycontactontheGT-TLI,a2-digitaccesscodemustbeentered
onthetelephonewhileincommunicationwiththedoorstation.Thedefaultcodeis20.
• Enter program access code 2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 30-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=2digitaccesscode)
Program Duration of GT-TLI Secondary Dry Contact
ThesecondarydrycontactontheGT-TLIcanbeactivatedforadurationof1-10seconds.Thedefaultis5seconds.
• Enter program access code 2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 32-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=timeinseconds,2digits)
When programming is complete dial 00 toexitprogrammingmode.
8 | GT-TLI Installation / Operation Instructions

SET UP - Advanced Programming
Ending Communication After Releasing Door on GT Entrance Panel
Choosetoendcommunicationimmediatelyafterdoorrelease(default),after5seconds,ornotatall.
• Enter program access code 2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 35-1longbeepwillbeplayed
• Enter 1(immediatedisconnect),1longbeepwillbeplayed,enter0-“Thecodeenterediscorrect”willbeplayed
• Enter 1(5sec.delay),1longbeepwillbeplayed,enter1-“Thecodeenterediscorrect”willbeplayed
• Enter 0(nodisconnect)-“Thecodeenterediscorrect”willbeplayed
Ending Communication After Activating Secondary Contact on GT-TLI
Choosetoendcommunicationimmediatelyafterdoorrelease(default),after5seconds,ornotatall.
• Enter program access code 2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 37-1longbeepwillbeplayed
• Enter 1(immediatedisconnect),1longbeepwillbeplayed,enter0-“Thecodeenterediscorrect”willbeplayed
• Enter 1(5sec.delay),1longbeepwillbeplayed,enter1-“Thecodeenterediscorrect”willbeplayed
• Enter 0(nodisconnect)-“Thecodeenterediscorrect”willbeplayed
DoorCallNoticationWhenLocallyConnectedTelephoneisinUse
Choosetoreceiveaverbalmessage(default)oratoneindicatingacallfromthedoorwhenthetelephoneisinuse.
• Enter program access code 2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 43-1longbeepwillbeplayed
• Enter 1(verbalmessage),or0(beep)-“Thecodeenterediscorrect”willbeplayed
Ring Style Selection For GT Entrance Panel Calls
Choosebetween1.5secondsofringingfollowedby3.5secondsofsilencerepeated(default)or1secondofringfollowedby1
second of silence repeated.
• Enter program access code

2000# -“Thecodeenterediscorrect”willbe played
• Enter 58-1longbeepwillbe played
• Enter 0(1.5sec.on-3.5sec.off)or1(1sec.on-1sec.off)-“Thecodeenterediscorrect”willbe played
Ring Duration Prior to GT-TLI Answering Outside Call
Enterthedurationinseconds(defaultis45sec.)thattheGT-TLIwillringbeforeansweringatelephonecall.Thisis
primarilyafactorwhenprogrammingfromanoutsideline.Timemustbesetinseconds,from10-255seconds.
• Enter program access code 2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 59-1longbeepwillbeplayed
• Enter nnn(timeinseconds,3digit)-“Thecodeenterediscorrect”willbeplayed
Change Program Passwords
Changepasswordsforbothgeneralparameters(defaultis2000)andcontrolledparameters(defaultis2001).
Thepasswordsmustbe4digitsandmustbedifferentfromeachother.
• Enter program access code 2000# or 2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 90(2000),orEnter91(2001)-1longbeepwillbeplayed
• Enter nnnn(nnnn=new4digitpassword)-“Thecodeenterediscorrect”willbeplayed
Language Selection for Voice Messages
Choosethelanguageforthevoicemessages(defaultisEnglish).
• Enter program access code 2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 78-1longbeepwillbeplayed
• Enter n(n=language,0=French,1=English,2=Spanish)-“Thecodeenterediscorrect”willbeplayed
9

10 | GT-TLI Installation / Operation Instructions
SET UP - Advanced Programming (continued)
Communication Level For Local Telephone
AdjustthereceiveandtransmitcommunicationvolumefortheGTentrancepaneltothelocallyconnectedtelephone.
Receive from GT Entrance Panel. The default setting = 04.
• Enter program access code 2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 06-1longbeepwillbeplayed
• Enter nn(nn=level,00maxlevel-31minlevel)-“Thecodeenterediscorrect”willbeplayed
Transmit to GT Entrance Panel. The default setting = 10.
• Enter program access code 2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 07-1longbeepwillbeplayed
• Enter nn(nn=level,00maxlevel-31minlevel)-“Thecodeenterediscorrect”willbeplayed
Communication Level for Remote Dialed Telephone
AdjustthereceiveandtransmitcommunicationvolumefortheGTentrancepaneltotheremotedialedtelephone.
Receive from GT Entrance Panel. The default setting = 04.
• Enter program access code 2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 08-1longbeepwillbeplayed
• Enter nn(nn=level,00maxlevel-31minlevel)-“Thecodeenterediscorrect”willbeplayed
Transmit to GT Entrance Panel. The default setting = 10.
• Enter program access code 2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 09-1longbeepwillbeplayed
• Enter nn(nn=level,00maxlevel-31minlevel)-“Thecodeenterediscorrect”willbeplayed
Time Setting for Delay Call Transfer
Setthedelaytimewhendelaycalltransferisenabled.Calltransfercanbedelayedfrom1-40seconds.
The default setting = 10.
• Enter program access code 2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 64-1longbeepwillbeplayed
• Enter nn(nn=timeinsec.,01-40)-“Thecodeenterediscorrect”willbeplayed
Switching to Communication Mode with Remote Telephone
Choosebetween3waysofswitchingtocommunicationwiththeremotetelephone.
0=switchifendofringingtoneisdetected
1=switchifDTMFdetected
2=switchimmediately(default)
• Enter program access code 2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 95-1longbeepwillbeplayed
• Enter n(n=mode,0-1-2)-“Thecodeenterediscorrect”willbeplayed