AIPTEK Qt CAM FLASH User manual

@n IP Company
Qt CAM FLASH
Installation Guide
English

How to Use Your Camera
Introduction
Installing Batteries
The built-in memory of your camera is 64 Mbit memory. It supports two kinds
of resolution- high resolution ( 640x480 VGA) for 26 pictures and low
resolution ( 320x240 QVGA ) for 107 pictures. Besides, your camera offers
several functions on the LCD, showing the remaining number of pictures as
well. With a USB cable, you can transfer all the pictures to your PC.
Your camera is powered by 4 AAA batteries or by a PC via a USB cable.
The upper 2AAA batteries are for Flash Strobe. The lower 2 AAA batteries
are for your camera.
***Notes ***
When batteries are removed, all of the stored
pictures are cleared. ( Battery Capacity: continuous
snapshot for 2 hours, stand by works for
approximately1 week.)
English
..1..

View Finder
Lens
USB Port
Shutter Switch( )SW1
Mode Switch( )SW2
LCD Display
Battery Cover
Flash Strobe
Flash Dial
Strap
View Finder
Camera Front
Camera Back
..2..

Selecting functions
Your camera has two switches - the shutter switch(SW1) and the mode
switch ( Sw2 ). As you keep pressing the mode switch, the LCD indicates "
Hr, 26,Ct, St, CL, and Lr" icons in order. To select the icon you want, press
the shutter switch. Note! If an icon is not selected within 5 seconds, the
LCD goes back to the picture remaining number. The following chart shows
the function of each icon.
Taking a picture
Press the shutter switch to take a picture.
A high pitched beep indicates that a
picture is taken successfully and the
counter decreases as well. A low beep
indicates insufficient light to take a picture.
A series of beeps suggest that the camera
is full.
Switching the camera on / off
Keep pressing SW2 until the LCD is
activated, and the camera turns off after
30 seconds of inactivity. The LCD
indicates "Lr" for low resolution (QVGA
images) and "Hr" for high resolution(VGA
images). The LCD then displays the
number of the remaining pictures. To turn
off the camera, press SW2 for 2 seconds. Press Sw2
LCD
is activated
Press Sw1 to take a picture
English
..3..

Change mode to "Ct"
Continuous mode
Press the mode switch until "Ct" appears on the LCD. You can take a series
of pictures in quick succession by holding down the shutter switch. The
function stops as you release the shutter switch. If the "Ct" icon is not
selected within 5 seconds, the LCD reverts back to the remaining number of
the pictures .
Press SW2 to change features
Features are displayed
Press SW1 to select mode
Low resolution ( 107 images at most )
Picture remaining number
High resolution ( 26 images at most )
Continuous snapshot
Clear all images
10-second self-timer
SW1
"Ct" is displayed
Press SW1 to select Continuous mode
..4 ..

SW1
Self timer
Press the mode switch until "St" appears on the LCD. Then press the shutter
switch and a 10 second self-timer starts. Every 10 second the camera issues
a short beep. When completing the self-timer, a longer beep sounds, which
indicates that a picture is taken.
Note: The self-timer can't work when the memory of your camera is full.
Change mode to "St"
"St" is displayed
Press SW1 to initiate the self-timer mode
Clearing all the stored
Press the mode switch until CL appears on the LCD. Press SW1 and after a
beep the LCD starts to flash . Press SW1 again within 5 seconds and all
and the picture counter are cleared.
the
camera memory
Change mode to "CL"
"CL" is displayed
Press SW1 to select clear mode
LCD starts to flash
Press SW1 to clear the memory
English
..5..

Changing the picture resolution
Picture resolution may only be changed when the camera memory is empty.
If there are any pictures stored in your camera, the memory must be cleared
first. To change resolution, press the mode switch until the resolution icon is
displayed. To select "Hr" or " Lr", press SW1. Then the LCD shows the
number of remaining pictures at the current setting.
Change mode to "Hr" or "Lr"
"Hr" or "Lr" is displayed
Press SW1 to change resolution
The flash is turned on.
The flash is turned off.
On:
Off:
Warning : Avoid direct exposure to eyes.
Flash strobe
Flash Strobe Button: It's on the back of your camera. Green light appears
on the square when flash strobe is activated. To activate flash strobe, move
the flash dial up.
SW1
..6..

How to Download Photo and Video to PC
Thank you for purchasing the digital camera. This guide will help you install
your camera onto your computer system.
Digital Camera Manager Installation
Place the CD into your CD-ROM and click on the Digital Camera Manager
Icon to begin the intallation.If the CD does not automatically display, simply
go to "Start" then "Run" and select the path "D:\Setup.exe". You may need
to replace "D" with the letter that corresponds to your CD-ROM drive.
Now your computer is initializing the Wise Installation Wizard. Please wait.
English
Digital Camera Manager
..7..

After the welcome screen appears, click "Next".
The CD begins installing the driver to the proper location.
The dialog box that appears asks if you would like to restart your computer
now or later. Press "OK" to complete installation.
..8..

Start Digital Camera Manager
The digital pictures can be transferred at all times, even if you take only one
picture. To connect your camera with your PC, you need a USB cable and
USB port. Your camera double beeps when successfully connected with
your PC. Don't worry! All of the stored images in your camera are still alive.
Your PC offers power for your camera. When disconnecting the USB cable,
your camera turns off automatically.
Connect the smaller end of the USB
cable to the USB port of your
camera.
Plug the larger end of the
USB cable to the USB port of
your PC.
Note: When plugged into a USB port, your camera is powered by the
PC. You may remove the batteries. However, all pictures are cleared
when the USB cable is unplugged.
=
=
English
..9..

Mode Selecting
=
=
Press the "Live View" button to change the camera to PC Camera mode.
Press the "DSC Function" button to change the camera to DSC &
Camcorder mode.
=
=
Live View (PC Camera Mode)
DSC Function (DSC Mode)
To start using the Digital Camera Manager, simply click on the "Start"
menu and go up to "Programs" Then go to the folder named "Digital
Camerar" and select it. This is the program where you can begin to use
your camera.
.. 10 ..

PC Camera Mode
It is easy to attach your camera to your system. our camera
is used as a standard PC camera.
In this mode, y
The current view is displayed in the "preview" window.
Press "Video Source" button to adjust
advanced settings.
Press "Video Format" button to set image size.
Press "Snap Shot" button to capture an image
to the album window.
Press "Record button" to record a video clip to
album window.
PC Camera Mode
Live preview
English
.. 11 ..

DSC Mode
Transferring Photos:
This allows you to transfer photos in your camera.
Press the "Link" button to connect the camera and transfer photos.
Press the "Album" button to open the album window.
<
=
>Press the "Transfer all" or "Transfer selected" button to transfer photos
to the album window.
Transfer pictures in your camera to your PC
Open or close album window
Transfer selected photos to album window
Transfer all photos to album window
.. 12 ..

Editing Photos:
It is easy to edit any photo you want in the album window. Double click the
photo icon to execute your default image application (such as Imaging,
Paint....etc.) to edit your image file.
Enhanced Resolution Mode:
. The Largest Resolution : XGA( 800K pixels )
. Optical Resolution: VGA ( 300K pixels)
Your camera has particular enhanced image skills, which make images
sharper by enhancing the original VGA image to XGA image.
How to operate:
Click the setting button.
Click " picture ".
Choose " Enhanced resolution ".
You can download your images again.
English
.. 13 ..

Transferring Video:
After transferring images to the preview window, click AVI Creator and all
images are combined in one AVI file. This AVI file is saved in your album
folder.
Note: Pictures in AVI files can be placed forward or backward.
AVI Creator:
<
=
Select Images you want.
Press "Setting" button to adjust frame rate.
>Press "AVI Creator" button to create an AVI file.
AVI Creator
(Reverse)
AVI Creator
.. 14 ..

Playing Video:
You can play any video clip file (AVI format) you want in album window by
double clicking the AVI file icon to execute your default media application.
Image processing:
Click the" Image Process" button to choose image settings.
English
Image Process
.. 15 ..

Album window:
Mail Function:
Click the "Mail" button to attach selected image to a new email document. It
is easy to send images to your family and friends!
Delete
Click the button. All the files you select in the album window
are cleared forever. Therefore, you should be very careful
with the delete button.
Select All
Click the button. You select all the files in the album window.
Making Your Album Folders
Click the button and key in your file name. Then you'll have a
new album folder, which can store lots of images or video files.
If you want to cancel any of the album folders, just select the
album and click the delete button below.
Transferring Image Files
Click the button. You transfer all the images in your camera to
your PC.
Mail
.. 16 ..