AIR-GRAPHICS Airbus H135 Juno HT.1 User manual

1:72
Scale
Juno HT.1
Airbus H135
CS-19
Conversion Set

Drawn: Gary Madgwick
CCopyright Gary Madgwick
Air-Graphic Models 2022
Airbus H135 Juno HT.1
1/72 Scale @ A5 12/08/2021
Drg No: CS-019 -01
Step made from
Plastic rod
15
10
11
21
20
15
12
12
16 13
14
21
16
24
24
25
25
29
Two small plasticard strips
Aerial stays

Cabin Assembly
1
1
Kit floor with seat risers sanded off.
Two thin plasticard strips which were
Sanded right down to almost nothing.
Kit parts
Optional kit/resin parts
Kit parts.
Note, see photos on next page
for correct layout of two seats
and the rear bulkhead
arrangement.
1
2
34
5
6
7
8
26
27
Kit part
Kit part
1
Only two seats, turned through 90 degree
as per picture
*Note, 2 small plasticard strips with
hes in on end.

Cockpit Continued
Above: Rear seats, note cabin colour
and seat colours. Also note rear
cabin bulkhead behind seats
Above: Front cabin seats are black with light grey cushions.
Note* two bars behind seats which will need to be made
From sprue, wire or plastic rod. These fit into the strip behind
The front seats.
Above: View forward from the rear cabin seats showing
fixing of the grab bars.
Above: Rear seats and cabin
bulkhead
Cockpit tub fitted into
fuselage half's.
Note fuselage
Modifications to take
New intake ducts for
The RAF aircraft. Also
The rear air grills parts
10 and 11 have been
Fitted. Note plasticard
Backing to help locate
These and secure.
Area cut back
10
Area cut back
10

Fuselage Modifications
3
12
10
11
14
13
13
14
Kit part
12
12
10
11
Kit clear
parts
Area cut back
9
Part 9 cabin roof
Instrument panel
position

4Tail detailing
Tail as per kit parts
Apart from part 15
Tail boom skid. Above right & below left: Completed fuselage and
tail during clean up process.
Modification to
Fin top.
16
15
Note, tail planes do not have the vertical
Planes. Remove these

5Final Detailing
22
19
17
21
Step made from plastic rod.
Note square end plates.
29
19
20
21
20
Note* Bear claw Part No 18
Not shown fitted for clarity
23
22
24
18
28
19
Note, tail planes should
Not be fitted.
Kit part
Thin plastic rod
stays to
tail aerial
Plasticard aerial
Note, tail planes should
not be fitted.
25

Air-Graphics: 24 Fyfield Close, Wantage, Oxfordshire,
OX12 8HN, UK.
E: [email protected]
INSTRUCTIONS
• Remove any flash by gently snapping off, or cutting
with a scalpel and then lightly sanding.
• Only use Super-glue or a two-part epoxy glue to fix
parts.
• Gluing is easier if mating surfaces are slightly sanded
to roughen the resin before gluing. Also clean off any
dust before gluing.
• Before paining, thoroughly wash all parts in warm
water with detergent.
• We recommend the application of a base coat in a
light colour to show any blemishes prior to final painting.
WARNING & SAFETY!
• These parts are moulded in polyurethane resin.
Please take care when sanding and cleaning up the
resin by wearing a dusk mask or other protective
breathing device to avoid inhalation of the dust
particles.
• Wash hands, resin parts and the work surface after
sanding resin.
• When using Super-glue or two-part epoxy glue, please
take precautions to avoid contact with skin and eyes.
• It is also advisable to wear a mask to avoid breathing
in any fumes from the glue or work in a ventilated room.
• The use of barrier creams on hands or wearing
disposable gloves, and working in a well ventilated
area, is strongly recommended.
• Not suitable to children under 14 years of age.
Thank you for purchasing this Air-Graphics product which
forms part of a range of accessories, conversion sets,
decals & kits all to 1/72 Scale.
13
12
11
10
9
8
7
6
5
4
32
1
X
14
15
16
17
18
19
20
21 22
23 24 25
26
27
28
29
Completed Model