Air Hogs Vectron Wave User manual

1
Contents:
1 Air Hogs®Vectron®Wave
1 Catching Stick
1 Charger
1 Instruction Guide
INSTR CTION G IDE
BATTERY REMOVAL AND INSTALLATION
The Air Hogs®Vectron®Wave is perfect for first-
time flyers. All you need is an open space and
6 x 1.5-V AA alkaline batteries (not included) to
take flight. Some assembly required.
ADULT SUPE VISION ECOMMENDED.
PLEASE READ THESE INSTR CTIONS
BEFORE FLYING!
Vectron®Wave Catching Stick Charger
1. equires 6 x 1.5-V AA alkaline batteries.
2. Open the battery door with a screwdriver.
3. If used batteries are present, remove
these batteries from the unit by pulling
up on one end of each battery.
4. Install new batteries as shown in the
polarity diagram (+/-) inside the battery
compartment.
5. eplace battery door securely.
6. Check your local laws and regulations for
correct recycling and/or battery disposal.
®
Battery Door
6 x
1.5-V AA
Alkaline
Batteries
Battery
Compartment
Attach the catching
stick to the Vectron®
Wave by pushing the
bottom of the stick into
the hole on the top of
the Vectron®Wave.
Use catching stick to
toss or catch the
Vectron™ Wave.
GETTING TO KNOW YO R VECTRON®WAVE
CHG/OFF/ON
Switch Charge
Socket
I Sensor
Power LED OFF ON/CHG
Switch
Power LED
Indicator
Stop ButtonI LED
I LED
Problems flying?
Do not return your
Air Hogs®to the store.
Call the Air Hogs®flight
training center at
1-800-622-8339

2
CHARGING YO R VECTRON®WAVE
1. Open door in charger to access the charge cable.
2. Plug charge cable into the charge port on Vectron®Wave.
3. Set switch on Vectron®Wave to charge.
4. Set switch on charger to charge. The Power LED Indicator on the charger
will turn red and flash. When the Vectron®Wave is fully charged the Power
LED Indicator will turn orange. This may take up to 30 minutes or longer if
the Vectron®Wave is fully discharged and the charger batteries are not new.
After fully charging, you should have about 5 minutes of play time.
NOTE: For better flight performance, fully charge your Vectron®Wave
before each flight.
CHG/OFF/ON OFF ON/CHG
1
234
AFTER CHARGING IS OVER
OFF ON/CHG
12
1. Set switch on charger to “OFF”.
INDOOR SE ONLY
1. Location – Fly in a wide open room, away
from breakable items. Minimum size 13 ft wide x
13 ft long x 10 ft high.
2. Avoid flying near vents and/or fans, as these
may overpower the Vectron®Wave and make it
difficult to control.
3. Sunlight or bright lights may affect your Vectron®
Wave’s performance.
4. Avoid flying near another I device. This may
affect your Vectron®Wave’s performance as well.
NOTE: Always get permission to fly your Vectron®Wave indoors.
2. emove charge cable from
Vectron®Wave and store in charger.
CA TION: Never fly near your face. Keep rotor
away from your fingers, hair, eyes and other body parts.
Always lift off from a flat surface. Never hold the Vectron®
Wave in your hand when lifting off. DO NOT launch
Vectron®Wave near people or animals. Stay away from
obstacles and electrical hazards.
13’ 13’
10’

3
HOW TO SE YO R VECTRON®WAVE
12
4 5
CHG/OFF/ON
CHG/OFF/ON
1. Turn your Vectron®Wave “ON”. After a few seconds
the propeller will begin to spin.
CA TION: otating propellers, please use care
when handling.
2. Set your Vectron®Wave on a flat surface or the ground.
NOTE: Your Vectron®Wave will go through a “Start- p
Process” at this point. First it will rise up, then it will
slowly fall, then it will rise up again. This helps it to
memorize the power required to hover on its’ own.
After it rises the second time the process is over and
you can begin to play. NOTE: During this process do not
touch or play with your Vectron®Wave as this will make
its’ hovering ability unstable.
3. Hand Play: The Vectron®Wave will hover above your
out-stretched hand.
4. Sliding or Tossing: Hold the Vectron®Wave by the
catching stick and tip forward 10-30°. Toss or slide gently
to another player.
5. When finished playing press the stop button on the
charger to turn the propeller “OFF” then turn the power
switch on the Vectron®Wave to “OFF”.
NOTE: If the Vectron™ Wave tips over or sticks to the ceiling,
use the STOP button on the charger to stop the propeller.
After pressing the stop button on the controller, the Vectron™
Wave will slow down and settle to the ground.
TRO BLESHOOTING
Charger LED is OFF
(not flashing).
Stop button is not working.
Charger LED is flashing ed/
Green alternatively while
charging Vectron®Wave.
1. Charger may be in sleep mode
(enters sleep mode after about
2 minutes of inactivity).
2. The batteries in the charger are drained.
1. Vectron®Wave is out of range.
2. Charger is in sleep mode.
1. Error while charging.
1. Turn charger OFF then ON again.
2. Install new batteries in charger.
1. Move charger closer to the
Vectron®Wave.
2. Turn charger OFF then ON again
or press stop button again.
1. Check that the connection between
the charger and the Vectron®Wave
is not broken, if it is reconnect.
PROBLEM SOL TIONCA SE
3
Beginning of
“Start- p
Process”
Finished,
Ready to
Play

4
TRO BLESHOOTING cont’d...
Charger LED is
flashing Green.
Vectron®Wave will not
start or has lost power.
Vectron®Wave is flying
too low.
NOTE: If normal function of the product is disturbed or
interrupted, strong electro-magnetic interference may
be causing the issue. To reset product, turn it completely
off, then turn it back on. If normal operation does not
resume, move the product to another location and try
again. To ensure normal performance, change the
batteries, as low batteries may not allow full function.
1. Batteries in charger are low.
1. You have not set the motor switch
to “ON”.
2. Charger battery power is low.
3. Batteries (+) or (-) are not correctly
placed inside the battery compartment.
4. Vectron®Wave battery is low.
1. The batteries in the charger are drained.
2. Vectron®Wave’s battery is low.
3. Hair or debris may be caught in the rotor.
1. Install new batteries in charger.
1. Slide motor switch to “ON”.
2. eplace the charger batteries.
3. Be sure to align the (+) and (-) polarities
with the corresponding markings inside
the battery compartment.
4. echarge Vectron®Wave.
1. Install new batteries in charger.
2. echarge Vectron®Wave.
3. emove hair or debris.
PROBLEM SOL TIONCA SE
TM
pin Master Ltd., 450 Front treet West, Toronto,
ON M5V 1B6 Canada
pin Master, Inc., PMB #10053, 300 International Drive,
uite 100, Williamsville, NY 14221, U A
pin Master Toys Far East Limited, Rm #1113, 11/F,
Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsui E.,
Kowloon, HK
North American Consumer Information
Phone: [phone]
www.spinmaster.com
®, TM and © 2009 pin Master Ltd. All rights reserved. Conforms to product safety
standards A TM F963, EN71 Regulatory Requirements. • Please retain this information
for future reference. • Please remove all packaging materials before giving to children.
• An adult should periodically check this toy to ensure no damage or hazards exist, if
so, remove from use. • Children should be supervised during play. • Keep addresses
and phone numbers for future reference. • The item inside this package may vary from
the photographs and/or illustrations. ubject to one or more U. . or world patents
under license from Go Wireless Ltd., including U. . Patent No. 7,147,535 and U. .
Design Patent No. D534467. MADE IN CHINA.
20019142, 20019143 NEN REV 0
IMPORTANT BATTERY INFORMATION
• equires 6 x 1.5-V AA alkaline batteries (not included).
• Batteries are small objects.
• eplacement of batteries must be done by adults.
• Follow the polarity (+/-) diagram in the battery compartment.
• Promptly remove dead batteries from the toy.
• Dispose of used batteries properly.
• emove batteries for prolonged storage
• DO NOT incinerate used batteries.
• DO NOT dispose of batteries in fire, as batteries may explode
or leak.
• DO NOT mix old and new batteries or types of batteries
(i.e. alkaline/standard).
• DO NOT use rechargeable batteries.
• DO NOT recharge non-rechargeable batteries.
• DO NOT short-circuit the supply terminals.
Your Vectron®Wave is equipped with a
Lithium Polymer battery.
WARNING:
• Never charge battery unattended.
• Charge battery in isolated area. Keep away from flammable
materials.
• Do not expose to direct sunlight.
• There is a risk of the batteries exploding, overheating, or
igniting. Do not disassemble, modify heat, or short circuit
the batteries. Do not place them in fires or leave them in
hot places.
• Do not drop or subject to strong impacts.
• Do not allow the batteries to get wet.
• Only charge the batteries with the specified Spin Master™
battery charger.
• Only use the batteries in the device specified by
Spin Master™.
• Carefully read the instruction guide, and use the batteries
correctly.
• In the unlikely event of leakage or explosion use sand or a
chemical fire extinguisher for the battery.
• Batteries must be recycled or disposed of properly.
This product complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesirable operation. This equipment has been tested and found to comply with the limits for Class B digital devices
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference to
radio communications. Because this toy generates, uses, and can radiate radio frequency energy, there can be no guarantee that
interference will not occur. If this toy does cause interference to radio or television reception (you can check this by turning the
toy off and on while listening for the interference), one or more of the following measures may be useful: • eorient or relocate the
receiving antenna • Increase the separation between the toy and the radio or the TV • Consult the dealer or an experienced TV-
radio technician for help. NOTE: Changes, adjustments or modifications to this unit, including but not limited to, replacement of any
transmitter component (crystal, semiconductor, etc.) could result in a violation of FCC rules under part 15 and/or 95 and must be
expressly approved by Spin Master Ltd. or they could void the user’s authority to operate the equipment.
This class B digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment egulations.