Air Vent FreeAir User manual

FreeAir
115-12-04
Description
The FreeAir active chilled beam is a two-way induction type
air-conditioning unit that is designed for exposed installation,
mounted directly against the ceiling. It is suitable for ventila-
tion, cooling and heating. The primary air from the air han-
dling unit is injected through the specially shaped nozzles and
discharged into the room along the ceiling. Causing induction
of the room air to ow through the cooling and/or heating
coil, which then mixed with the primary air ows back into the
room through the linear slot openings on the two sides of the
beam. The conditioned/mixed air discharged along the ceiling
provides the optimal coanda eect which is always the objec-
tive when the occupied zone requires low air velocities.
Air duct connection: Ø100 mm
AirFlex
- Less risk of draft
- Shorter throw length
- Individually adjustable
AirFlex- adjustable air deectors
FreeAir is equipped with AirFlex air deectors, which can be
manually and individually adjusted on each side of the air
slots, as a standard option. AirFlex allows the operator to easily
adjust the direction and throw distance of the discharged
conditioned air. With the ne-tuning capabilities of the AirFlex
deectors, a highly exible, pleasant and draft-free indoor
climate can be achieved.
Materials
The duct and plenum air box are made of galvanized steel.
The visible front plate and side panels are powder coated
sheet steel painted in standard white RAL 9003 colour (or
in any other RAL colour requested by the customer). The
heat exchanger ns are made of aluminium, and the pipes
are made of copper. The AirFlex air deectors are made of
polyamid plastic. Square or circular perforation as standard
options.
Square or circular perforation as standard options
Airvent reserves the right to change specifications.
www.airvent.eu
FreeAir
Maintenance and installation
guide.
Active chilled beam

215-12-04
FreeAir
Maintenance and installation guide
Mounting instructions
FreeAir is mounted against the ceiling. For the suspension
there are xing points towards the ceiling. The air and water
can be connected from the short side or from the top. Factory
installed control equipment available in several designs, con-
tact Airvent for detailed information.
Suspension points
309
L3
37
37
L5L2 L4L1
149
ø9
108
I. Suspension type
II. Suspension type
1.
2.
3.
I. Suspension type II. Suspension type
Suspension points
309
L3
37
37
L5
L2 L4L1
149
ø9
108
I. Suspension type
II. Suspension type
1.
2.
3.
I. Suspension type II. Suspension type
Distance between suspension points
Size L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) Suspension points
1200 563 563 6
1500 463 500 463 - - 6
1800 563 600 563 - - 6
2100 488 525 525 488 - 8
2400 563 600 600 563 - 8
2700 503 540 540 540 503 10
3000 563 600 600 600 563 10
Suspension points
309
L3
37
37
L5L2 L4L1
149
ø9
108
I. Suspension type
II. Suspension type
1.
2.
3.
I. Suspension type II. Suspension type
Airvent reserves the right to change specifications.
www.airvent.eu

FreeAir
315-12-04
Maintenance and installation guide
Dimensions
L
W(573,6)
105
75
ød
60
H(120)
Ød
309
L3
100
37
L5
L2 L4L1
149
ø9
108
W1(405,4)
82
CWin CWout HWin HWout
Dimensions
Size
(mm)
Dimensions (mm) Weight
(kg)
Water
volume(l)
L W W1 H Ød
1500 1500
573,6 405,4 120 100
27 1,4
1800 1800 29 1,6
2100 2100 32 1,9
2400 2400 34 2,2
2700 2700 37 2,5
3000 3000 40 2,7
Tube dimensions
Number of water circuits 15 18 21 24 27 30
1Ø12
2 - - Ø15
Heating Ø12
Airvent reserves the right to change specifications.
www.airvent.eu

415-12-04
FreeAir
Maintenance and installation guide
Maintenance
The perforated front panel of the active chilled beam can
be folded down allowing easy access for maintenance. The
heat exchanger have to be cleaned by carefully using a
vacuum cleaner so that the aluminium ns and the copper
tubes are not damaged. The parts that are out of reach for
the vacuum cleaner have to be wiped o with a soft cloth. If
required, mild preferably neutral cleaning detergent could be
used. The electrical parts have to be maintained in accordance
with the relevant prescriptions. The points of connection/
shock protection and the functional ability of the components
must be checked. The maintenance operation has to be car-
ried out at least twice a year.
1.
2.
1.
2.
1.
2.
Airvent reserves the right to change specifications.
www.airvent.eu