AIRBORNE 5000 User manual

5000

8
9
3
5
6
7
2
1
4
10

English
1 Call Back
2 Talk button/R Button
3 Caller ID/Scroll button
4 *and ring signal off/on
5 INT calls
6 Programming/Conrm
7 Delete/mute button
8 #and keyguard
9 Disconnect button
10 Phonebook
Français
1 Touche Bis
2 Touche de Prise de ligne et R
3 Touche de navigation / Journal des
appelants
4 Touche *et Sonnerie Off/On
5 Appels internes
6 Touche de Programmation /
Conrmation
7 Touche Effacer/Secret
8 Touche #et de verrouillage du clavier
9 Touche de Raccroché
10 Répertoire

1
English
Connection
1. Connect the mains adapter (6V DC) and the telephone cord to the wall sockets.
2. Insert the batteries (AAA 1.2V 650 mAh NiMH) into the handset with plus/minus
as indicated.
3. Chargethehandsetwiththekeypadfacingoutwards(for24hoursthersttime).
Range
The telephone’s range depends on whether or not the radio waves carrying the call are
restricted by obstacles in their path, and is usually between 50 and 300 metres. Coverage
can be improved by turning one’s head so that the handset is aligned with the base unit.
Soundqualitydeclinesasthelimitisreacheduntilthecallisnallyinterrupted.
The symbol isshownwhenthephoneiswithinrangeandasheswhenitisoutofrange.
Battery
As batteries only have a certain lifespan it is quite normal that call time and standby time will
decreasesomewhatcomparedtothespecicationswhenthetelephoneisusedregularly.
Fully-charged batteries (10 hours charging) will last for approx. 110 hours standby time
or approx. 8 hours call time. These times apply at normal room temperature.
Full battery capacity will not be reached until the batteries have been charged 4-5 times.
The base unit has an automatic charging mechanism that prevents the batteries from
being overcharged or damaged due to prolonged charging.
Battery LED
When the batteries are running low, the indicator will show and a warning tone will
be heard once when the indicator drops to its lowest level during a call.
Please note that the battery indicator in the handset display rotates while charging and
will stop when the battery is fully charged.
Making a call
1. Enter required telephone number (C=delete).
2. Press qto dial the number. Press Lto terminate the call.
Receiving a call
1. Wait for the handset to ring.
2. Press qto answer. Press Lto terminate the call.
Please note!
When the batteries are low (NO BATT) or when there is too great a distance to the base unit the
telephone will be unable to connect to the line.
The charging connections should be cleaned regularly with a soft cloth and/or an eraser.
The base unit should not be located close to other electrical equipment, in direct sunlight or near any other
strong heat source! This is to minimize the risk of any interference.
It is normal for the device to become warm during charging and this is not dangerous.
Use only original batteries. The guarantee does not cover any damage caused by incorrect batteries.

2
English
Volume control
The volume can be adjusted during a call with 8/9.
Call Back
Press rto display the most recently dialled number. Press qto dial.
Mute button
The microphone can be switched off/on during a call with C( =off).
KeyGuard
The keyguard can be activated ( =on) by pressing down #, and deactivated by
pressing any button followed by 0.
Incoming numbers/Caller ID
In the display you can see who is calling and the 10 most recently received calls.
New calls are indicated by in standby mode.
If one and the same number calls in more than once it will be saved as only one entry.
This function requires a subscription from your service provider.
Retrieving and dialling incoming numbers
1. Scroll to required position with 8/9.
2. Press 0to switch between name*, number and time/date.
3. Press qto dial, press bto save number in phonebook or press Lto return to standby.
*The name can only be displayed if it has been stored in the phonebook.
Deleting numbers
1. Scroll to the desired entry as described above.
2. Press C.
3. Conrmbypressing0.
Deleting all numbers
1. Scroll to the desired entry as described above.
2. Press down Cuntil the display shows RST LIST.
3. Conrmbypressing0.
Calleridenticationmessages
In addition to number display, the following messages are shown sometimes:
INTERNAT No information received, e.g. an international call.
PRIV NUM Information about the number is blocked. Number cannot be shown.
Number not previously seen.
Message indication (sent from your network operator to indicate a
message waiting)*.
*Message indication can be deleted manually by pressing down Lfor a few seconds in
standby mode.

3
English
Paging
The handset will ring when (on the base unit) is pressed. The signal will stop
automatically after a while or if Lon the handset is pressed or on the base unit.
Phonebook
10 telephone numbers (max. 20 digits) with names (max. 8 letters) can be stored in the
handset’s phonebook. If you subscribe to a caller ID service, the name allocated to the
caller in the phonebook will be shown for incoming calls.
Letters
Each number key has been allocated certain letters.
1.....................................[Space]
#(press & hold)..............Pause in telephone number
Save name/number in handset
1. Enter the telephone number, including the area code (C=delete). Press b.
2. Press equivalent digit key one or more times for desired name. Press 0.
3. The telephone number is shown again. Press 0toconrm.
Dialling from the phonebook
1. Press b.
2. Scroll between entries with 8/9. A quick search is also possible by pressing the
correspondingnumberkeyfortherstletter.
3. Press qto dial the number.
Changing telephone numbers/names
1. Press b. Scroll between entries with 8/9.
2. Press b.
3. Correct the name entry with C. Press 0.
4. Correct the number entry with C. Press 0.
Deleting a phonebook entry
1. Press b. Scroll between entries with 8/9.
2. Press C.
3. Conrmbypressing0.
Delete entire phonebook
1. Press b.
2. Press down Cuntil the display shows RST LIST.
3. Conrmbypressing0.
If you want a pause in the telephone number, press down #until the display shows P.

4
English
Settings
1. Press 0.
2. Scroll to the required function with 8/9according to the list below e.g. R. Press 0.
3. Scroll to required setting. Press 0.
4. Press Lto return to standby mode.
Command Function
..................................Ring signal type/volume for the handset
................................Ring signal type/volume for the base unit
.....................................Flash time (1=standard, 2=France/Portugal)
.................................Tone/Pulse (1=tone/normal, 2=pulse)
....................................Registration, see separate description
*The ring signal in the handset can also be connected/disconnected with *( =off).
PIN code
The PIN code (four digits) provides protection against unauthorized use of certain functions.
1. Press 08.
2. Enter the current PIN code (0000 when supplied). Press 0.
3. Enter the new code. Press 0.
4. Enter the new code again. Press 0.
To reset settings
1. Press 0.
2. Press down Cuntil RESET? is shown.
3. Press 0.

5
English
Expanded system (only +1…)
All handsets included in the package are already registered to the base unit. The handset
number used for internal calls is shown in the display on standby mode.
The base unit should be positioned centrally so that the coverage area is roughly equal
for all handsets.
It is not possible to add extra handsets at a later point.
INT calls
1. Press I.
2. Enter the allocated number of the handset that you wish to call, 1- 4.
A tone will be heard if an external call comes in while an internal call is in progress.
Terminate the internal call by pressing Land press qto answer the external call.
Transferring calls/Conference between handsets
1. An external call is connected.
2. Initiate an internal call as described above.
3. Press Lto transfer the call or press down Ifor a few seconds for conference.
Register
Every new handset must be registered in order for it to be able to use the base unit in
question. Every base unit can manage up to 4 different handsets.
1. Press 0.
2. Scroll to with 8/9. Press 0.
3. Enter the base unit’s PIN code (0000 on delivery). Press 0.
4. Hold down the button on the base unit until you hear two beeps.
5. If the registration is successful the handset will return to standby mode within one minute.
De-registering another handset
1. Press 09.
2. Enter the required handset 1-4. Press 0.
3. Enter the base unit’s PIN code (0000 on delivery). Press 0.

6
English
Troubleshooting
Check that the telephone cord is undamaged and properly plugged in. Disconnect any
additional equipment, extension cords and other phones. If the problem is resolved, the
fault is with some other equipment. Test the equipment on a known working line (e.g.
at a neighbour’s house). If the equipment works there the fault is probably with your
telephone line. Please inform your network operator.
Check the charge status of the handset batteries.
If the telephone still does not work, contact the place of purchase. Don’t forget the
receipt or a copy of the invoice.
Specic Absorption Rate (SAR)
This device meets approved international safety requirements for exposure to radio
waves. This telephone measures 0.05 W/kg (measured over 10g tissue).
The max. limit according to WHO is 2W/kg (measured over 10g tissue).
Declaration of conformity
Doro hereby declares that the product Airborne 5000 conforms to the essential
requirements and other relevant regulations contained in the Directives 1999/5/EC
(R&TTE) and 2002/95/EC (ROHS).
A copy of the manufacturer’s declaration is available at www.doro.com/dofc
Guarantee
This product is guaranteed for a period of 12 months from the date of purchase. Proof
of purchase is required for any service or support required during the guarantee period.
This guarantee shall not apply to a fault caused by an accident or a similar incident
or damage, liquid ingress, negligence, abnormal usage, not reasonably maintained or
any other circumstances on the purchaser’s part. Furthermore, this guarantee shall
notapplytoafaultcausedbyathunderstormoranyothervoltageuctuations.This
guarantee does not in any way affect your statutory rights. (As a matter of precaution, we
recommend disconnecting the telephone during a thunderstorm.)
UK
Ifyoucannotresolvethefaultusingthefaultndersection,technicalsupportisavailable
by email on [e-mail]
-premium rate telephone number: 0905 895 0854, calls cost 50 pence per minute
(prices correct at the time of publication).
You can also contact us in writing (regarding any Spares or Technical query):
Customer Services
Doro UK Ltd
1 High Street
Chalfont St Peter
Buckinghamshire
SL9 9QE.
Further contact details are available on our website: www.doro-uk.com.

1
Français
Raccordement
1. Reliez le bloc d’alimentation (6V CC) et le câble téléphonique aux prises murales.
2. Insérez les batteries (AAA 1,2V 650mAh NiMH) dans le combiné en respectant la
polarité (+ et -).
3. Placez le combiné sur le chargeur, le clavier tourné vers l’extérieur et chargez-le 24
heures en continu avant la première utilisation.
Portée
En général, la portée du téléphone varie de 50 à 300 mètres en fonction de l’environnement.
Vous pouvez améliorer la portée en tournant la tête de façon à pointer le combiné vers la base.
La qualité du son se détériore quand le combiné se rapproche de sa limite de portée, puis
la communication est coupée.
Le symbole s’afchequandletéléphoneestàportéeetclignotequandilesthorsdeportée.
Batterie
Les batteries ayant une durée de vie limitée, l’autonomie en veille ou en communication
peutvarierparrapportauxspécicationsdonnées.Desbatteriescomplètementchargées
(charge de 10 heures) ont une autonomie d’environ 8 heures en communication et
110 heures en veille. Ces durées sont données pour une utilisation à l’intérieur à des
températures normales. Les batteries sont complètement chargées au bout de 4 à 5
charges. La base a un système de recharge automatique qui évite de surcharger les
batteries ou de les endommager par une charge prolongée.
Témoin de charge
Quand le niveau de charge des batteries s’affaiblit, le témoin s’afche.Si,encoursde
communication, la charge du combiné est faible, le combiné émet un signal sonore.
Veuillez noter que le témoin des batteries du combiné clignote pendant la charge et
s'arrête quand les batteries sont complètement chargées.
Appeler
1. Composez le numéro (C=effacer).
2. Appuyez sur qpour appeler le numéro. Appuyez sur Lpourmettrenàla
communication.
Recevoir un appel
1. Attendez que le combiné sonne.
2. Prenez l’appel en appuyant sur q. Appuyez sur Lpourmettrenàlacommunication.
Remarque !
Vous ne pouvez pas prendre la ligne lorsque les batteries sont faibles (NO BATT) ou quand le combiné
est trop éloigné de la base. Nettoyez régulièrement les contacts de charge avec un chiffon doux et/ou uneNettoyez régulièrement les contacts de charge avec un chiffon doux et/ou une
gomme. Ne placez pas la base à proximité d'appareils électriques, d'une source de chaleur ou dans unNe placez pas la base à proximité d'appareils électriques, d'une source de chaleur ou dans un
endroit exposé directement au soleil an de minimiser les risques d'interférences. Vous pourrez observer
un réchauffement de l'appareil pendant la charge ; ce phénomène est normal. Utilisez uniquement des
batteries d’origine. La garantie ne couvre pas les dommages causés par d’autres batteries.