Airbutler VICTOR 230 User manual

Function:
By combination of three of the world’s most recognized technologies of purification,AIRBUTLER
VICTOR 230 is able to achieve comprehensive purification: dust purification, removal of bacteria and
elimination of unpleasant odours. All that can be achieved by means of a very powerful generator of
ions. It produces negatively charged ions that are able to remove suspended particles from the air and
thus purify the air. Active oxygen is in the position to destroy bacteria, viruses and mites. The power
consumption for the mechanics of filtration, purification and for the fan is 14 W only.
Bond of dust:
After a few days of use, you will find a considerable deposit of air pollutants on the different filter
systems (such as metal plates) and on the „PLASMA DUST COLLECTOR”. Those filter systems purify
the air in the interior of the AIRBUTLER PARKER 120 (by eliminating dirt particles and bacteria even
smaller than 0.1 μm). The ionisation wires ensure an enrichment of negatively charged ions in the local air.
Well-being effect:
AIRBUTLER VICTOR 230 removes dust, odours and bacteria within a minimum of time and supports
well feeling in general. You can breath fresh and pleasant air.
USER MANUAL VICTOR 230
Electronic ioniser – Indoor air purifier
Attention! Do not touch needle when unit is turned on!
VICTOR 230

14
INSTRUCTIONS FOR OPERATION
Locate the appliance on a solid surface. Be sure the grille is not blocked by other objects and that there
are no candles or flames near the unit.
Before plugging in the unit, please open the windows in the area where you will be using the unit.
Ventilate the area for 2-3 hours if possible. Once the area has been ventilated, close the windows and
plug in the unit. (Figure 1)
Plug in. Plug into nearest standard electrical outlet.
Switch on. Press the power button and the appliance starts to operate under AUTO mode.
The colour of clean sign will change alternately for 1 minute, and then the clean sign will revert to cur-
rent air condition. (Figure 2)
CAUTION!
For first time use or re-operate the appliance after unplug, the sensor needs to be pre-heated
for 3-5 minutes and will not respond during this period. Besides, if the current air quality is not
good, it is recommended to purify the air manually first and then switch back to AUTO mode,
otherwise the sensitivity of the sensor may decrease.
When re-operating the appliance after long period being unused, the
sensitivity of the sensor may decrease. It will revert to normal sensitivity after 1-2 days operation.

15
CONTROL PANEL INSTRUCTIONS
A) ON/ OFF BUTTON
By pressing BUTTON A once, you can switch on the unit and the display screen will illuminate. The appliance
will start to operate under AUTO MODE. By pressing it twice, the unit is switched off.
B) AUTO MODE / FAN SPEED
By repeated pressing of BUTTON B you can adjust the air fan speed or operate under AUTO MODE.
Symbol I shows which of the four levels have been selected:
AUTO MODE
Low for silent mode
Medium for normal use
High for maximum cleaning
Once the AUTO is activated, appliance will automatically sense and adjust the air cleaning speed once
it detects pollutants in the air.
C) OPERATION WITH CATALYST
BUTTON C is used for switching the catalyst on and off (Symbol “UV+TiO ” lights up). This appliance combi-
nes advanced catalytic technologies to reduce odours and chemical fumes from glues, solvents and synthetic
materials when air passes through the filter and is activated by the internal UV LED. (The catalyst system can-
not be removed). If turned off, the appliance will continue filtering particles from the air that passes through
the filter but its odour and VOC capability will be significantly reduced.
D) TIMER
Using BUTTON D, the operation time can be set. It is selectable between 1~9 hours or continuous ope-
ration (continuous), Symbol J shows the operating period that has been set (1h/2h/3h/4h/5h/6h/7h/8h/9h/
continuous)
E) NIGHT MODE
By pressing the BUTTON E once, the night mode is switched on which automatically dims the display bright-
ness. The appliance continues operating in silent mode. If BUTTON E is pressed again, the appliance will no
longer be in night mode.

16
F) CLEANING INDICATOR
If red “C L E A N C E L L” indicator appears on the display, the appliance
should be cleaned as recommended by the manufacturer. When the
collector cell is re-installed after cleaning, switch on the appliance
and keep pressing the BUTTON E at least 3 seconds until buz-
zer beeps, red “C L E A N C E L L” indicator disappears and “CLEAN
C E L L” timer is reset.
G) CATALYST INDICATOR
Informs about the operation mode of the catalyst.
H) REPLACE INDICATOR
When red “REPLACE FILTER” indicator appears on the display, the VOC/Formaldehyde filter should be
replaced as recommended by the manufacturer.
Reset “REPLACE FILTER”
When the VOC/Formaldehyde filter is re-installed after replacement, switch on the appliance and keep pres-
sing the BUTTON D at least 3 seconds until buzzer beeps, red “REPLACE FILTER” indicator goes out and
“REPLACE FILTER” timer is reset.
I) FAN SPEED INDICATOR
Symbol I shows which of the four levels have been selected:
Low: for silent mode
Medium: for normal use
High: for maximum cleaning
AUTO MODE: Once the AUTO MODE is activated, appliance will automatically sense and adjust the
air cleaning speed once it detects pollutants in the air. Additionally 4 stages of clean sign,
clearly shows your current air condition accordingly.
Geen: Clean
Light Orange: Low pollution
Orange: Medium pollution
Red: High pollution
J) TIMER INDICATOR
Shows the operating period that has been set (1h/2h/3h/4h/5h/6h/7h/8h/9h/ circulated).
The display will automatically show the current value after a few seconds.

17
CLEANING AND MAINTENANCE
CLEANING
When the red “ C L E A N C E L L” indicator is blinking, please restart your appliance. If the red “CLEAN
C E L L” indicator is still blinking, please clean your collector cell. When the red “ C L E A N C E L L” indicator illu-
minates or collector cell is too dirty or if snapping sounds become frequent, please clean your collector cell.
Proper care and cleaning of the air purifier is critical to performance. The following chart shows the
cleaning intervals and method.
PLEASE FOLLOW YOUR USER‘S GUIDE TO CLEAN.
Cabinet: As needed | Wipe with damp cloth first. If required, follow with mild non-
abrasive cleaner.
Collector Cell: 4 to 8 weeks | Spray specialized cleaner or soak in warm water or warm water
with mild liquid detergent. Rinse and dry.
Pre-Filter: 2 to 4 weeks | Rinse thoroughly in warm water or as needed.
Air Direction Grille: As needed | Use the brush provided with the air purifier to brush away debris in
between the slots.
VOC/ Formaldehyd Filter: 6 to12 month or as needed | Replace with a new filter.
CLEANING THE PRE-FILTER
1. Unplug the appliance.
2. Open the front cover by gently pulling from the top corners.
3. Pull the pre-filter straight out of the cabinet.
4. Thoroughly rinse the pre-filter and let it air dry before placing it
back in the cabinet. Do not use heated or compressed air as part
of the drying process.
5. Slide the pre-filter back into the unit.
6. Close the front cover securely.
WARNING!
Cleaning the unit while it is plugged in may result in electric shock,
electric spark and serious injury.
Unplug the unit before cleaning or maintenance.

18
CLEANING THE COLLECTOR CELL
1. Unplug the appliance.
2. Open the front cover by gently pulling from the top corners.
3. Remove the collector cell by unlocking top and bottom knobs and
pulling straight out.
4. Separate the collector cell from the wire assembly for easier access
to each during cleaning.
5. Place each in sink, bathtub or other location where cleaner can
cover every surface.
6. Spray specialized cleaner between each cell plate and cover each
surface. Allow the cleaner to soak for a few minutes but do not let it
dry. Thoroughly rinse the collector cell with clean water.
An alternative method to clean the collector cell is to rinse or soak it in
warm water for loose debris. Mild liquid dish detergent in water may
also be used to help break down tough dirt and residue. Thoroughly
rinse the collector cell with clean water.
7. Place the collector cell under the sunlight to dry at least 3 hours. Shake excess water from the
collector cell to speed up drying time. Do not use heated or compressed air to dry.
8. Reassemble the wire assembly and collector cell by inserting the post located on the outside edge
of the wire assembly into the recessed channels of the collector cell. After guiding the post into the
recessed channels, slide the wire assembly until it locks into place.
9. Place the collector cell back into the unit by sliding it straight in and turning each knob to its locking
position. The collector cell is specially designed so that it can only be inserted in one direction.
10. Close the front cover securely.
Note: Please refer to instructions on page 16 for resetting after cleaning, otherwise the indicator will
remain on screen.
CAUTION!
The collector cell may not require cleaning if “arcing” occurs. Arcing is a sharp snapping sound
that occurs when large particles are collected in the collector cell or the
appliance used in overdamp rooms.
If prolonged or continuous arcing occurs, the collector cell should be cleaned.
CAUTION!
To prevent damage to the components of the collector cell, do not put in
dishwasher or use acotton swab.
Tough residue such as tar from tobacco smoke may need additional cleaning or longer soaking.

19
CLEAN CELL INDICATOR IS BLINKING
The collector cell must be completely dry after cleaning in
order to operate properly. In case the residual water left
in the collector cell gap, the red “ C L E A N C E L L”
indicator will blink rapidly once operation.
In this case, please re-dry the collector cell under the sunlight, and then
restart the appliance. If the red “C L E A N C E L L” indicator is off, the appli-
ance will return to original and run as normal. If not, please repeat above
method to re-dry until the red “ C L E A N C E L L” indicator is off.
REPLACE THE FORMALDEHYDE FILTER
1. Unplug the appliance.
2. Open the front cover by gently pulling from the top corners.
3. Pull the formaldehyde filter straight out of the cabinet.
4. Replace with a new filter.
5. Close the cover securely.
Note: Please refer to instructions on page 16 for resetting after
cleaning, otherwise the indicator will remain on screen.
CLEANING THE EXHAUST GRILL
1. Remove the cleaning brush from the storage slot located under the front cover.
2. Brush away debris that has collected between the grille slots.
3. Return the cleaning brush to the storage slot.

20
TROUBLESHOOTING
Service problems that appear to be major can often be solved easily. You can be your own troubleshooter by
reviewing this guide. All other servicing should be done by a local authorized service center.
PROBLEM CHECK SOLUTION
Appliance does
not turn ON
Power cord
Power button
Front cover
Plug in power cord
Press the POWER BUTTON
Make sure the front cover is securely closed
Red “CLEAN CELL“
indicator has
illuminated
Collector cell Please wash collector cell and reset the timer.
Refer to instructions on page 16.
Red “REPLACE
FILTER“ indicator has
illuminated
Filter Please replace filters and reset the timer.
Refer to instructions on page 16.
Red “CLEAN CELL“
indicator is blinking
Collector cell When a large particle is captured in the collector cell,
please restart your appliance.
A fast blinking light indicates the collector cell is not properly
installed, please reinstall the collector cell.
A fast blinking light indicates the power supply has shut down
due to arcing or short circuit. The cell should be inspected and
cleaned, repaired or replaced.
The collector cell is not completely dry after cleaning,
please re-dry it.
Collector cell does not
remove particles
Collector cell Clean the collector cell.
Collector cell may be damaged.
Contact authorized service center.
Appliance sparks,
crackles and pops.
Collector cell Sparking or poping noise (arcing) can occur when a large particle
is captured in the collector cell or appliance is used in over
damp rooms.
If the appliance is arcing excessively, the cell may be dirty.
Try cleaning the collector cell.
If excessive arcing continues after proper cleaning, the
collector cell may be damaged.
If damaged, contact authorized service center
“AUTO“ indikator
is blinking
Surroundings Air quality is bad, please open the window to improve
the ventilation.
“AUTO“ indikator
is blinking
Sensor Sensor get malfunction, should be repaired or replaced.

21
SPECIFICATIONS
High performance DC fan, low energy consumption, durable use.
Night operating mode, quiet and comforting.
Built-in smart sensor, automatic sensing and adjust airflow speed, intelligent operation.
Plasma electrostatic dust collector, easy to clean, never needs to be replaced.
Large volumes of air rapidly circulate and purify air.
High performance filter effectively removes extra fine particles of 0.1 - 0.3 microns.
Negative ions and activated oxygen rapidly remove odour and smoke to freshen the air.
UV LED is energy-saving, effectively sterilize and kill bacteria.
Multiple professional filters effectively remove harmful gases like acetone and benzene etc.
SAFETY INSTRUCTIONS
Only use the appliance indoors and within the parameters stated in the technical specifications.
Using the appliance for a purpose for which it is not intended could pose a serious hazard to health
and life. Children cannot realize the hazards associated with the usage of electrical appliances. For
this reason, always supervise children when they are near the appliance.
Never use the appliance if there is any damage to the appliance or cable, after malfunction has
occurred, after the appliance has been dropped or damaged in any other way.
Repairs to electrical appliances may only be carried out by qualified service engineers.
Improper repair work can pose a serious hazard to the user.
Do not run the power cord under a carpet or other objects. Position the appliance so that you will
not trip over the cord.
Do not handle the unit with wet hands. Never pull the plug from the mains socket by the cable or
with wet hands.
Hair, loose clothing and body parts can get caught in the machine resulting in injury. Keep hair,
loose clothing and body parts away from openings and moving parts.
Do not use an extension cord.
Do not place the appliance near sources of heat such as: stove tops, ovens, radiators or computers.
Do not place open flames, including candles, directly in front of the air purifier.

22
Do not use the appliance in an enclosed space where flammable, combustible or explosive gases
are present.
Do not use in an area where toxic vapours, flammable dust or oxygen tanks are present. Check the
location and make sure these elements are not present.
This equipment should be inspected frequently and the dirt that has collected should be removed
regularly to prevent excessive accumulation that may result in flashover or fire.
Do not insert foreign objects from the front grille, high voltage inside.
Do not defeat interlock.
Place the appliance on a flat, solid, stable surface. Never place the unit on soft surfaces such as a
bed or sofa.
It is important to keep all objects away from the front and exhaust grille, keep at least 30cm distances.
Place the appliance away from TV, computer or radio, keep at least 100cm distances.
Do not use the appliance on wet surfaces or use it in damp locations, such as bathroom.
Do not sit, stand or place any heavy objects on the appliance.
Position the appliance so that the dirty air is not drawn across your head or body while sitting or
sleeping.
Place the appliance so the plug on the power cord easily reaches a standard electrical outlet for a
polarized plug.
This appliance is not a substitute of daily ventilation and cleaning or kitchen ventilation.
Please unplug the appliance if the power cord or plug gets heated, burned smell or weird noise.