Airline DB038 User manual

•The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample
may be said to have been obtained.
•This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability
are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any
loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its
marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced
from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek
certification program.
•For Terms And Conditions of the services, it can be provided upon request.
•The evaluation data of the report will be kept for 3 years from the date of issuance.
TRF No.: FCC 15C_Tx_b
Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch
6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China
Tel: [phone] Fax: [phone] Website: www.china.intertek-etlsemko.com
Airline Mechanical Co., Ltd
Application
For
Certification
FCC ID: ZGIDA065
Remote wall switch with Z-WAVE
Model: DB038
Additional Model: DA065, ZFM-80US, ZFM-M80US
Transceiver
Report No.: SZ12060359-1
We hereby certify that the sample of the above item is considered to comply with the
requirements of FCC Part 15, Subpart C for Intentional Radiator,
Mention 47 CFR [ 10-1-11 ]
Prepared and Checked by: Approved by:
Sign on file
Andy Yan
Engineer Billy Li Supervisor
Date: July 14, 2012
Digitally signed
by Billy Li
Location: Intertek
Testing Services

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
i
LIST OF EXHIBITS
INTRODUCTION
EXHIBIT 1: General Description
EXHIBIT 2: System Test Configuration
EXHIBIT 3: Emission Results
EXHIBIT 4: Equipment Photographs
EXHIBIT 5: Product Labelling
EXHIBIT 6: Technical Specifications
EXHIBIT 7: Instruction Manual
EXHIBIT 8: Miscellaneous Information
EXHIBIT 9: Test Equipment List

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
ii
MEASUREMENT/TECHNICAL REPORT
Airline Mechanical Co., Ltd - Model: DB038
Additional Model: DA065, ZFM-80US, ZFM-M80US
FCC ID: ZGIDA065
July 14, 2012
This report concerns (check one:) Original Grant X Class II Change
Equipment Type: DXT - Part 15 Low Power Transceiver, RX Verified
Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X
If yes, defer until:
date
Company Name agrees to notify the Commission by:
date
of the intended date of announcement of the product so that the grant can be issued on that
date.
Transition Rules Request per 15.37? Yes No X
If no, assumed Part 15, Subpart C for intentional radiator −the new 47 CFR [10-1-11
Edition] provision.
Report prepared by:
Billy Li
Intertek Testing Services Shenzhen Ltd.
Kejiyuan Branch
6F, Block D, Huahan Building, Langshan Road,
Nanshan District, Shenzhen, P. R. China
Phone: [phone]
Fax: [phone]

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
iii
Table of Contents
1.0 General Description............................................................................................2
1.1 Product Description............................................................................................2
1.2 Related Submittal(s) Grants ...............................................................................2
1.3 Test Methodology...............................................................................................3
1.4 Test Facility........................................................................................................3
2.0 System Test Configuration.................................................................................5
2.1 Justification........................................................................................................5
2.2 EUT Exercising Software....................................................................................5
2.3 Special Accessories...........................................................................................5
2.4 Equipment Modification......................................................................................5
2.5 Measurement Uncertainty ..................................................................................6
2.6 Support Equipment List and Description.............................................................6
3.0 Emission Results................................................................................................8
3.1Radiated Test Results…………………………………………………………………. 9
3.1.1 Field Strength Calculation................................................................................9
3.1.2 Radiated Emission Configuration Photograph................................................10
3.1.3 Radiated Emissions.......................................................................................10
3.1.4 Transmitter Spurious Emissions (Radiated)…………………………………….. 12
3.2 Conducted Emission at Mains Terminal…………………………………………… 14
3.2.1 Conducted Emissions Configuration Photograph………………………………..14
3.2.2 Conducted Emissions………………………………………………………………14
4.0 Equipment Photographs...................................................................................18
5.0 Product Labelling..............................................................................................20
6.0 Technical Specifications...................................................................................22
7.0 Instruction Manual ............................................................................................24
8.0 Miscellaneous Information ...............................................................................26
8.1 Bandedge Plot .................................................................................................27
8.2 Emissions Test Procedures..............................................................................29
9.0 Test Equipment List..............................................................................................32

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
iv
List of attached file
Exhibit type File Description Filename
Test Report Test Report report.pdf
Test Setup Photo Radiated Photos radiated photos.pdf
Test Setup Photo Conducted Photos conducted photos.pdf
Test Report Bandedge Plot bandedge.pdf
Test Report 20dB BW Plot bw.pdf
External Photo External Photo external photos.pdf
Internal Photo Internal Photo internal photos.pdf
Block Diagram Block Diagram block.pdf
Schematics Circuit Diagram circuit.pdf
Operation Description Technical Description descri.pdf
ID Label/Location Label Artwork and Location label.pdf
User Manual User Manual manual.pdf
Cover Letter Letter of Agency agency.pdf

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
1
EXHIBIT 1
GENERAL DESCRIPTION

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
2
1.0 General Description
1.1 Product Description
The Equipment Under Test (EUT) is a Remote wall switch with Z-WAVE
transceiver connected directly to AC 120V/60Hz main line. The EUT is a
remote controlled On/Off switch for household appliance and it is designed to
act as a repeater, which will re-transmit the 908.42MHz RF signal (when
receive a command signal from the remote controller) to ensure that the
signal is received. It also has manual function. For more detail, please refer to
the user manual.
The Model: ZFM-M80US is the same as the Model: DB038 in hardware
aspect. The models are difference in plastic colour, packaging and marketing
purpose only.
The Models: DA065, ZFM-80US are the same as the Models: DB038 in
hardware aspect of RF portion. The difference between the models is as
below.
DB038, ZFM-M80US with power meter function.
DA065, ZFM-80US without power meter function.
Antenna Type: Integral antenna
Modulation Type: FSK
For electronic filing, the brief circuit description is saved with filename: descri.pdf.
1.2 Related Submittal(s) Grants
This is an application for certification of a transceiver for the Remote wall switch
with Z-WAVE. The verification procedure of the receiver portion of this
transceiver is being processed at the same time.

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
3
1.3 Test Methodology
Both AC mains line-conducted and Radiated emission measurement were
performed according to the procedures in ANSI C63.4 (2009). Radiated
emission measurement was performed in semi-anechoic chamber and
conducted emission measurement was performed in shield room. For radiated
emission measurement, preliminary scans were performed in the semi-
anechoic chamber only to determine the worst case modes. All radiated tests
were performed at an antenna to EUT distance of 3 meters, unless stated
otherwise in the "Justification Section" of this Application.
1.4 Test Facility
The Semi-Anechoic chamber and shielding room used to collect the radiated
data and conducted data are Intertek Testing Services Shenzhen Ltd.
Kejiyuan Branch and located at 6F, Block D, Huahan Building, Langshan
Road, Nanshan District, Shenzhen, P. R. China. This test facility and site
measurement data have been fully placed on file with the FCC (Registration
Number: 242492).

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
4
EXHIBIT 2
SYSTEM TEST CONFIGURATION

INTERTEK TESTING SERVICES
Report No: SZ12060359-1
FCC ID: ZGIDA065
TRF No.: FCC 15C_TX_b
5
2.0 System Test Configuration
2.1 Justification
The system was configured for testing in a typical fashion (as a customer would
normally use it), and in the confines as outlined in ANSI C63.4 (2009).
The EUT was powered by AC 120V/60Hz during the testing.
The models DB038 and DA065 have been tested for radiated emission and
AC conducted emission, only the worst case is shown on this report.
For maximizing emissions, the EUT was rotated through 360°, the antenna
height was varied from 1 meter to 4 meters above the ground plane, and the
antenna polarization was changed. This step by step procedure for
maximizing emissions led to the data reported in Exhibit 3.0.
The rear of unit shall be flushed with the rear of the table.
The equipment under test (EUT) was configured for testing in a typical fashion
(as a customer would normally use it). The EUT was placed on a turn table,
which enabled the engineer to maximize emissions through its placement in the
three orthogonal axes.
2.2 EUT Exercising Software
The EUT exercise program (provided by client) used during radiated and
conducted testing was designed to exercise the various system components in a
manner similar to a typical use.
The parameters of test software setting:
During the test, power controlling software provided by the applicant was used
to control the operating channel.
2.3 Special Accessories
No special accessories used.
2.4 Equipment Modification
Any modifications installed previous to testing by Airline Mechanical Co., Ltd
will be incorporated in each production model sold / leased in the United
States.
No modifications were installed by Intertek Testing Services Shenzhen Ltd.
Kejiyuan Branch.