Airone AE10 User manual

Page 1 of 12

Page 2 of 12
AirOne mini Wi-Fi
Dashboard Camera
User Guide AE10

Page 3 of 12
About this guide
Every effort has been made to ensure the accuracy of the user guide, but
there is no guarantee that the following content will be free of errors. Also,
specifications may be slightly different due to product improvements.
WARNING
1.Failure to comply with safety warnings and regulations can result in
serious injury or death.
2.Please only use original charge cable included to power the device
3.Dash Cam is not intended to be touched, modified, or calibrated while
operating a vehicle.
4.We are not responsible for any damages resulting from the user's
misuse of the camera.
5.Do not use damaged power cords or plugs, or loose electrical sockets.
Faulty connections can cause electric shock or fire.
6.Do not touch the car charger with wet hands or disconnect the charger
by pulling the cord. Doing so may result in electrocution.
7.Do not short-circuit the charger or the device. That may cause electric
shock or fire, or cause the battery to malfunction or explode.

Page 4 of 12
1. MicroUSB Interface
2. AV-IN Slot-Backup Camera(optional)
3. TF Card Slot
4. MButton - Menu / Emergency Lock / Delete
5. Down Button - Down / Mute / Fast Forward / Parking Monitor
6. Power Button - Turn Off Screen
7. OK-Turn On Recording / Take Photo / Play Back
8. Up Button - Up / Fastback warding.
What’s In the Box:
A. 1×AIRONE Dash Cam
B. 1×AIRONE Hardwire Kit
C. 1×Car Mount
D. 1×User Guide QR Card

Page 5 of 12
Installation of wiring
Connect the following three cables to the car fuse box. (The position of the
fuse box differs depending on the model)
A. Yellow cable (BAT/B+) 20A / 20A+
The yellow cable should be connected to the fuse of the constant power
supply in the car fuse box. If you are looking for a constant power supply in
the fuse box: Use a voltage tester to check the fuse to ensure it still have
electricity even if the car engine is off.
B. Red cable (ACC) 5A / 10A
Connect the red cable to a fuse that can supply power only when the car
engine starts. Testing method: the tester bulb will light when the engine is on
or no light when the engine is off.

Page 6 of 12
C. Black cable (GND)
Connect this black cable(GND) to the metal part of the vehicle. Most cars
have screws or metal parts next to the fuse box. Connect the black cable to
the screw or metal part.(As in the picture below)
Button Description
1. Power Button:
a. Power On: when the dash cam is off, press and hold POWER button
for 3 seconds to turn it on.
b. Power Off: when dash cam is on, press and hold POWER button for 3
seconds to save all videos and settings, and to turn it off.
c. Screen On/Off: when dash cam is in standby mode, press POWER
button to turn on or off screen.
Note: dash cam automatically start recording once powered on. There is a round red button
blinking on the up left corner of screen. Press OK to stop recording, and dash cam is in
standby mode.
2. M Button – Menu / Emergency Lock/Delete:
a. Mode change: in standby mode, press Mbutton to select different
modes on right side of the screen, including photo, video, and
playback.
b. Emergency lock: in video mode, press Mbutton to lock and save the
video. Lock sign will pop up on screen, and video will not be
overwritten.
c. Menu: in standby mode, press and hold Mbutton for 3 seconds to
enter menu. Press UP or DOWN to select settings, and press OK to
confirm. Press Mto return back. Same apply to turn on recording, take
photo, and play back.
d. Delete: in playback mode, press and hold Mbutton to enter delete
page, and press OK to confirm.

Page 7 of 12
3. ＞Up Button – Up / Fast Back Warding:
a. Up: in menu or playback mode, press UP to turn into last page.
b. Fast Backward: when in playback video playing mode, press Up to
fast backward video.
4. ＜Down Button – Down / Mute / Fast Forward / Parking Monitor.
a. Down: in menu or playback mode, press DOWN to turn into next
page.
b. Mute: in video mode, press DOWN to mute. Mute sign will pop up
on screen. Press DOWN again to turn it on. Mute sign will
disappear.
c. Fast Forwarding: when in playback video playing mode, press
DOWN to fast forward video.
d. Parking monitor: in standby mode, press and hold DOWN to start
parking monitor.
5. OK Button – Turn On Recording/Take Photo/Play Back:
a. Confirm: in menu or playback mode, press OK to confirm Up or
Down.
b. Turn on/off Recording: in video mode, press OK to start recording,
and press it again to turn it off.
c. Take photo: in photo mode, press OK to take one photo.
d. Play back: in playback mode, press OK to play.
Function Description
1. Video Automatic Recording:
AirOne video recording is automatically activated once the vehicle is started.
Charging light is on, and recording light is blinking. When vehicle engine is off,
dash cam automatically save all content and shut down. All saved files are in
TF card. Once full, it will be overwritten. Recording length can be changed at
setting menu, 1 min, 3 min or 5 min.
Note:
a. If selecting one of 1/3/5 min, videos will be overwritten once TF card becomes full.
b. Video and photo files can be found in DCIM folder of TF card.
2. Video Manual Recording:
Press power button, AirOne dash cam will turn on and automatically record.
Charging light is on, and recording light is blinking. Press and hold power to
turn it off. All files will be automatically saved.

Page 8 of 12
3. Take Photo:
When dash cam is on, press M to take photo. Video sign turns into camera
sign on the upper left corner of screen. Press OK to take photo. To return
back to video, press M twice.
4. Gravity Sensor:
Your AirOne dash cam contains G-sensor, which enable to lock and save
video when serious car crush is detected. Video is locked shown on the
screen. Those videos will not be overwritten.
5. One-Key Lock:
AirOne dash cam has one-key lock feature, where all locked videos are
protected to avoid overwritten. In video recording mode, press M to lock
video.
6. Date and Time Setup:
In standby mode, press and hold M to enter setting menu. Press Up/Down to
select Date/Time. Press OK to enter, and press M to switch among
Year/Month/Day/Hour/Minute/Second, press Up/Down to adjust values, and
press OK to confirm.
Note: please adjust all dates correctly before using your AirOne dash cam, so all locked
video can be used as evidence of accidents with correct date / time.
7. One-Key Mute and One-Key Park Monitoring:
In recording mode, press DOWN to mute when recording. Mute sign appears
on top of the screen. Press DOWN again to mute, and sign disappears.
In standby mode, press and hold DOWN to enter park monitoring, and press
and hold DOWN to cancel.
Note: all setting will be automatically saved.
8. Video Playback:
In recording mode, press M twice, and your AirOne dash cam is in playback
mode. Press UP/DOWN to find the file, and press OK to play. Press M to
return back to recording mode.
9. Park Monitoring:
When your AirOne dash cam has park monitoring on, when your car has slight
turbulence or shake, dash cam will automatically start recording and lock the
video. If your dash cam is on during the turbulence, your dash cam will record
for 15 seconds and go back to normal recording mode. If the dash cam is off,
recording will continue for 15 seconds and power off.

Page 9 of 12
10.Motion Detection:
In standby mode, press and hold M to select Motion Detection. Once it’s on,
your AirOne dash cam can record 10 seconds video when it detects any
motion changes.
Note: Your AirOne dash cam has battery. Please do not leave it OVERHEATED! This
documentation is only for reference. Please see your device as final model. With the device,
you should drive carefully to avoid traffic accident or violation. The company will not be
responsible for any errors, fines, or accidents occurred when using the device.
Troubleshooting
Trouble
Possible Reasons
Solution
Dash cam not on
Wires not connected
Re-connect wire
Do not record
No TF card
Insert TF card
TF card broken
Change TF card
TF card not eligible
Insert correct TF card, and
format it to FAT32
Note The dash cam supports up to a class 10 micro TF card up to 128GB. Do not remove or
insert the micro TF card when the camera is working. Suggested micro TF card brands:
Samsung, Sandisk, Transcend. Do not use the Car Charger to charge devices with Quick
Charge technology. Install the car mount on windshield that are titled on an angle between
-17°C~68°C (1-155°F).
Mobile Phone Connection
1. Scan the QR code to download and install RoadCam app.
2. Add the dash cam to the app.

Page 10 of 12
a. Tap Ok button, stop recording, and then tap the ＞UP button 5
second, the camera Wi-Fi turn on.
b. Tap Wi-Fi Connecting.
c. In Wi-Fi list, select the Wi-Fi SSID of the target dash cam and enter Wi-Fi
password to build connection.
d. Tap the Take Photo icon, connect the AirOne dash cam, Run the
RoadCam app.
e. Tap ＞UP button 5 seconds, turn off Wi-Fi hotspot.
*Dashcam Wi-Fi default parameters: Wi-Fi Name: wifi_camera_ac54_××××××
*Wi-Fi password: 12345678 (Please edit password after login for the first time)
3. Edit the dash cam password to active it to avoid abnormal recording after
connecting to Wi-Fi.