airquee 8ft Platform Curved Bounce 'n' Slide 3D Operating instructions

Version 1.1 11/01/17
Page 1of 4
8ft Platform Curved Bounce ‘n’ Slide 3D
IMPORTANT
AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUT
YOUR OWN RISK ASSESSMENT BEFORE ATTEMPTING TO USE THIS PRODUCT.
Site survey:
1. Carry out a survey of the area where the ‘8ft Platform Curved Bounce ’n’ Slide 3D’ will be
located, and check for any overhead/underground cables. It’s important that this is carried
out to avoid ground anchors penetrating underground services, and the ‘8ft Platform Curved
Bounce ’n’ Slide 3D’ coming into contact with overhead cables when inflated.
2. You should provide an adequate power supply to the fan, this should adhere to
your local power regulations.

Page 2of 4
3X
3. Check wind speed: The industry recommends a maximum wind speed of Force 5
on the Beaufort scale of 28 - 38 kmph (19-24 mph). Force 5 is a fresh breeze when
small trees in leaf begin to sway.
Included with your ’8ft Platform Curved Bounce ’n’ Slide 3D’:
Extra equipment needed in addition what is supplied with your inflatable:
Suitable 240v Power Supply to operate the fan.
Disco light and speaker
Extra equipment you could consider for your new inflatable:
Ground sheet to protect the underside of your inflatable
Sandbag covers to anchor your inflatable indoors.
Sack truck to move your inflatable safely
RCD for your fans
Crash Mats
This inflatable can be set up and packed away by 3 people who have
had proper manual handling training and use the correct equipment to
move the inflatable.
Set up:
The first step is to unfold the unit according described in the Land Manual.
IMPORTANT: The electrical Items that you choose to use in your inflatable must meet the
safety standards of the country you are operating in. You must ensure all items are CE
marked.
If you wish to use lights with your unit, please insert it into the lights holder (fig. 1) through the
zips located on the roof of the inflatable as seen on figure 2. after the unit is unfolded, but
BEFORE it is inflated. The lights should come with a separate instructions manual, which
contains the safety instructions you should take into consideration before installing it in the unit.
It is important to insert the lights facing down.
The inflatable
in its bag Anchor Pegs Wiring Harness –
installed in the unit Land Operation Manual

Page 3of 4
LIGHTS HOLDER
ZIPS FOR INSERTING THE LIGHTS
WIRING HARNESS
By default, the unit is equipped with electric wiring for the lights as seen on fig. 3.
After the light is inserted in the corresponding place and plugged in, the unit can be inflated.
After the unit is totally inflated you may insert the speaker. You must secure it with the two
webbing straps. See fig. 5.
Fig. 1
Fig. 2
Fig. 3

Page 4of 4
Fig. 5
Fig. 4
The speaker shown in this instruction manual is for illustrative purposes only.
IMPORTANT INFORMATION REGARDING
YOUR SPEAKER –PLEASE READ!
Extended exposure to very high volume sound can cause serious damage to hearing. Please
exercise caution when setting the volume and remember that inside the dome the sound is
enclosed and much louder!
Deflation:
Before deflating the unit, the disco speaker will be unplugged and taken out from the unit.
After the unit is deflated the disco light can be taken out.
IMPORTANT:
The electrical wiring used within the unit is not water proof or water resistant. When
inflated, the air pressure will prevent ingress of water into the unit but it cannot be
guaranteed to stop all water reaching the electrical parts. Therefore, we do not
recommend operating the unit in the rain.
When operating the unit with lights, for preventing an electrical shock, please use the
supplied RCD device.
When the unit is deflated the light and speaker should be removed as soon as possible
and stored safely. The wiring harness should be left in place and the unit should be rolled
to prevent water lying on the unit and seeping into the sockets. If you suspect water has
entered in any of the electrical components they should not be used until completely dry
and tested. We recommend taking professional advice where necessary.
All cables and electrical equipment must be tested in accordance with the regulations of
your country.
In accordance with HSE guidelines all 240v equipment should be protected with an RCD
having a maximum trip current of 30 mA.