airquee Active Crocodile Slide Operating instructions

Version 1.0 12/07/17
Page 1of 5
Active Crocodile Slide
IMPORTANT
AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUT
YOUR OWN RISK ASSESSMENT BEFORE ATTEMPTING TO USE THIS PRODUCT.
Site survey:
1. Carry out a survey of the area where the Active Crocodile Slide will be located, and check for
any overhead/underground cables. It’s important that this is carried out to avoid ground anchors
penetrating underground services, and the Active Crocodile Slide coming into contact with
overhead cables when inflated.
2. You should provide an adequate power supply to the fan, this should adhere to your local power
regulations.
3. Check wind speed: The industry recommends a maximum wind speed of Force 5 on the
Beaufort scale of 28 - 38 kmph (19-24 mph). Force 5 is a fresh breeze when small trees in leaf
begin to sway.

Page 2of 5
Included with your Active Crocodile Slide:
Extra equipment needed in addition what is supplied with your inflatable:
•Suitable 240v Power Supply to operate the fan
Extra equipment you could consider for your new inflatable:
•Ground sheet to protect the underside of your inflatable
•Sandbag covers to anchor your inflatable indoors
•Sack truck to move your inflatable safely
•RCD to attach to your extension lead
•Crash Mats
This inflatable can be set up and packed away by 2 persons who have
had proper manual handling training and use the correct equipment to
move the inflatable.
Intended use of the product:
- Please be aware that this is not a bouncy castle
and should not be used for bouncing on.
The inflatable
in its bag Electrical Timer Anchor Pegs
Intended user height and number:
User Height: UP to
1.0M
1.25M
1.5M
1.6M
Number of Users
6
6
6
6
Dimensions:
Length
Width
Height
Inflated Unit
10M
(32.8ft)
5.6M
(18.36ft)
4.8M
(15.74ft)
Weight:
Unit
Inclusions
Total
219KG
72KG
291KG
2X
Land Operation
Manual Repair Kit

Page 3of 5
Fig. 2
Fig. 3
Please see below the anchor points of the unit:
Set up:
- After unfolding the unit please connect the fans as it is shown above:
a) the 2 HP fan to the mouth movement filler pipe
b) the 1.5HP fan to the main filler pipe
- Please note the Mouth Movement filler pipe contains a flexible plastic pipe inside (fig. 1), that
directs the airflow directly from the fan into the chamber beneath the mouth. It is imperative to
tie the strap at the proximity of the bed (outside, fig 2.), and in the chamber beneath the
mouth (inside fig. 3) because these cam buckle webbing straps secures the flexi pipe, and
prevent it from moving.
16 GROUND ANCHOR POINTS IN TOTAL
FLEXIBLE PIPE INSIDE THE UNIT
2 HP FILLER PIPE
(FOR MOUTH MOVEMENT)
1.5HP MAIN
FILLER PIPE
Fig. 1
OUTSIDE STRAP
INSIDE STRAP

Page 4of 5
ZIP
(FOR ACCESSING THE FLEXI PIPE)
AIR RELEASE FLAP
Fig. 4
- There is a second flexi pipe inside the unit. It is located in the chamber underneath the mouth.
Its function is to direct the airflow from the bed into the top parts of the unit. Without this pipe,
the head of the crocodile wouldn’t inflate. Before inflating the unit, you must make sure this
flexi pipe is connected on both sides, and is fully functional.
You can verify them through the zip shown on the picture below.
- Switch on all fans to start inflation. Check around the Slide to make sure that it does not come
into contact with any obstructions.
- For the jaw to be able to drop, the fan must stop, and the air has to exit through the “Air Release
Flaps”seen on fig. 4. You can automate this movement of the jaw by connecting the supplied
electrical timer between the main electric socket and the electrical socket of the 2HP fan, which
will turn the fan ON and OFF in the selected time intervals.
2HP FAN SOCKET
ELECTRICAL SUPPLY SOCKET
BED
TOP PART
AIRFLOW

Page 5of 5
IMPORTANT
IT IS IMPERATIVE THAT THE MOVING JAW WILL BE USED ONLY AS A
CLIMBING SHEET. THE CHILDREN WHO ARE USING THE UNIT SHOULD
BE INSTRUCTED TO KEEP A CONTINUOUS MOVEMENT.
For adjusting the timing of the mouth, please follow the instructions below:
The electrical timer is designed to turn the fan ON and OFF at user defined intervals.
This timer is can be adjusted asymmetrically: i.e. the fan can be on for 15 seconds
and off for 25 seconds, hence asymmetrical.
IMPORTANT
PLEASE MAKE SURE THAT THE TIMER HAS BEEN DISCONNECTED
FROM THE POWER SUPPLY BEFORE REMOVING THE LID.
- In order to adjust the timer, first you’ll need to remove the plastic lid.
- Inside the box you will find 4 dials. With the help of these you’ll be able to adjust
the desired ON and OFF time intervals –see images below:
- Once you have selected the correct range with the ON dial, all you need to do is
alter the OFF dial to achieve the run and pause times desired.
All the pictures and drawings are for illustration purposes only.
ENJOY AND HAVE FUN!