Airthereal FL-100H User manual

USER MANUAL
READ AND SAVE THESE INSTRUCTIONS
FL-100H & FL-101S
FLOWLESS WATER LEAK DETECTOR
WITH WI-FI GATEWAY

CONTENTS
PRODUCT STRUCTURE DIAGRAM
SPECIFICATIONS
SET UP AND OPERATION
SET UP THE WATER LEAK DETECTOR
MODE CONTROL WITH AIRIA
SETTING MENU FOR THE GATEWAY
SETTING FOR WATER LEAK DETECTOR
BASIC SETTING AND INFORMATION SHARING
LOW BATTERY REMINDERS
LIMITED WARRANTY
················································02
············································································04
······························································05
········································13
························································19
···········································22
·····································23
···························30
··························································31
······································································32

2
PRODUCT STRUCTURE DIAGRAM
Wi-Fi Gateway
Warning Light
Power Indicator
Volume Tone
Setting

3
Water Leak Detector
Indicator
Sensor
Alarm Probe
AAA Battery
Test Key
Airthereal Water Leak Detector sounds an alarm after detecting water drips or leaks.
After connecting to Wi-Fi, it instantly sends alert notifications to the app wherever you are.
*433 is a communication protocol with a frequency of 433MHz.
Note: Obstacles or products of the same frequency (433MHz) will affect the reception
of information.

4
SPECIFICATIONS
Wi-Fi Gateway
Model: FL-100H
Power Supply: AC 100-240V, 50-60Hz
Battery: 450mAh 3.7V Li-ion
Alarm Volume: 120dB
Standby Time: 7h
Connect: 24 Detectors Max
Water Leak Detector
Model: FL-101S
Sensor Contact: Detect water drip
Sensor Contact: Detect water leak(0.5mm)
Test Button: Pause alarm / Adjust volume
Batteries: 2 x AAA Battery
Alarm Volume: 120dB
IP Waterproof Rating: IP66
Packing List
3 X Water leak detector
1 X Wi-Fi gateway
6 X AAA battery
1 X User manual

5
SET UP AND OPERATION
Wi-Fi Gateway
1. Power: Power on / off (Battery powered).
For AC power: The gateway will automatically turn on when connected to the power
supply. (When powered on, the Gateway will beep and the warning light will flash
once).
For Battery: The gateway will automatically charge when plugged into AC power.
(The power indicator changing from red to green means that the battery is fully
charged).
2. Tone: Short press to select different alarm sounds.
3. Volume: Short press to adjust the volume of the gateway. (4 levels of volume + mute,
default is the loudest setting).
Loudest levels: The warning light will flash twice, and the gateway will beep twice.
Mute: Warning light will flash twice.

6
4. Setting: Short press to adjust mode.
Please refer to page 10 for the specific introduction of each mode.
Mode
Armed
Disarmed
Home
SOS/Alert
Reaction
One beep sound
Two beeps sound
Three beeps sound
Can’t set

7
Checking the Water Leak Detector
Step 1 Install the battery

8
Step 2
Press the button [Test], and the detector will beep. Press again to pause the alarm.
Note: If there is no beep, open the back cover to check whether the positive and
negative directions of the battery are installed correctly.
Press the button once.

9
Step 3
Adjust alarm volume by pressing and holding the test button for 3 seconds.
Press and hold for 3s each time to adjust one level of volume.
Long press the button 3s.
4 (DiDiDiDi-maximum sound)
3 (DiDiDi)
2 (DiDi)
1 (Di-mute)

10
Step 4
Test that the device can detect water. The detector will alarm if you drip some water
on the sensor contacts or put it on a wet surface.
Note: There are four detection sensors on the bottom of the device. Two detection
sensors in parallel lines will immediately alarm when they detect water. Two sensors
in diagonal lines will not alarm when they detect water at the bottom of the detector.
Water Leak Water Drip Not Alarm

11
Step 5
Press the test button to stop the alarm. Remove the device from the water and dry
the sensors to stop the alarm completely.
The first alarm will last for 15 seconds. If the sensor alarm ends and there is still
water, the sensor will continue to alarm every 15 seconds until dry or you press the
test button to end.
When the detector is still immersed in water after 24 hours, the detector will stop
the alarm.

12
Installing Your Device
1. Plug the gateway into a power outlet or use the battery supply.
2. Lay the water leak detector flat where you want to detect water leaks.
Note: Keep the distance between the gateway and the detector less than 100m/328ft.

13
SET UP THE WATER LEAK DETECTOR
Preparation Before Connecting
1. Make sure your Wi-Fi router supports 2.4GHz (NOT 5GHz) and 802.11b/g/n bands.
Note: Most 5GHz routers can also be set to 2.4GHz band or dual band.
2. Make sure the Wi-Fi name and password are correct.
3. A smartphone or tablet supporting a 2.4GHz network.
4. Download the App named AIRIA from the App Store(iOS devices) or Google Play
(Android devices).
Google Play App Store

14
Step 1
1. Connect your phone to the 2.4 GHz network your gateway will use.
2. Open AIRIA and tap the “+” icon in the top right corner.
3. Click Auto Scan, enter the finding page.

15
Step 2
Entering the Wi-Fi connection mode:
Press and hold the “Volume” and “Alarm” buttons to enter the connection mode.
The Warning Light will blink quickly. Make sure the gateway is powered on.

16
Step 3
1. Finding the gateway in the finding page, go to the next step.
2. Enter the password of your Wi-Fi network when prompted (same Wi-Fi network on
which your smartphone is connected) and then click confirm.
Important note:
The alarm unit must be connected to a 2.4 GHz Wi-Fi network. If your router (internet
box) broadcasts 2 Wi-Fi bands (2.4GHz and 5GHz), consult your router user manual
to learn how to select the 2.4 GHz Wi-Fi band.

17

18
Step 4
Your device is now connected successfully. You can find the gateway in the device list.

19
MODE CONTROL WITH AIRIA
The above buttons are used to manage the system:
Armed
This Mode should be used when you go out and there is no one at home.
(Detector will trigger the alarm regardless of any Zone Attribute.)