AirTrack Factory AirFloor User manual

USER MANUAL
SPORTS

ENJOY YOUR EQUIPMENT!
Thank you for purchasing our home training equipment!
Please make sure to read through these safety instructions carefully before using your Equipment.
Should anything be unclear, do not hesitate to contact us! We hope you enjoy your new equipment.
Train safe, have fun and level up!
SPORTS

CONTENT
Safety Instruction
Set-up & packing
Problem solving
FAQ
6
8
10
11
Chapter Page

6SPORTS www.airtrackfactory.com - [email protected] - Tel. [phone]
RECOMMENDED PRESSURE
The bounciness of the equipment depends on the pressure. If lled up to the maximum pressure,
our equipment can feel like a standard gymnastics oor (which is useful for competition training). At
low pressure the equipment feels nice and soft, but be careful to not bottom out!
Note: It is impossible to over-pressurize our equipment with the blowers we supply. To prevent
damaging the equipment, never use a blower other than the one supplied with your equipment.
The thickness of our equipment has an eect on how the equipment can be used. Most of our
equipment for home use is 10 cm thick. This goes for the AirFloors, AirBeams, and AirBoards.
The pressure in the equipment needs to be high enough to prevent you from hitting the oor
and soft enough for a comfortable bounce. We have recommended pressures for our home
equipment, but in the end it’s up to the users’ preferences.
Body weight 10 cm thick 20 cm thick (P2)
20 - 30 kg 70 - 80 mbar 40 - 50 mbar
30 - 60 kg 70 - 100 mbar 40 - 60 mbar
60 - 90 kg 100 - 140 mbar 60 - 70 mbar
90+ kg 150 mbar 75 mbar
PLAY IT SAFE

7www.airtrackfactory.com - [email protected] - Tel. [phone]
These instructions apply to all inatable equipment from AirTrack Factory that can be used at home as
well as in a gym.
Important: This equipment is not a toy. It is professional training equipment for gymnastics, cheerleading,
tumbling, school sports, showgroups, martial arts, parkour, freerunning and tricking.
USE EQUIPMENT ONLY FOR THEIR INTENDED PURPOSE
Personal
• This equipment is not suitable for children under
5 years.
• Do not allow more than one person at a time to
use the equipment.
• Do not wear shoes while on our equipment for
they may damage the surface.
• Do not jump or land closer than 20 cm to a valve.
• Consult an instructor prior to use.
• Use our equipment only under the supervision of
trained and qualied instructors.
• Use equipment with trained spotters and the
proper spotting equipment.
• Follow a progressive learning pattern. Assure
basic skills are achieved before attempting more
advanced skills.
Positioning and set-up
• Do not bring any sharp items on or close to the
equipment.
• Never place equipment near overhead
obstructions, such as low ceilings, trees or power
lines, nor place the equipment on a slope greater
than 5%.
• The area on which the equipment is placed
must be clean, dry, at and free of obstacles and
walls.
• Always set up the equipment in the same area
where you will be using it. Do not drag or throw it.
Lift it by the handles and avoid scraping.
• Do not use the equipment in humid areas,
electrocution may occur.
Pressure
• Do not use a compressor. Use only ination
equipment supplied by AirTrack Factory.
• Check the air pressure of the equipment
before each training session.
• Assure that the equipment has sucient air
pressure to avoid bottoming out. Recommended
air pressure levels can be found in this user
manual.
• Use equipment only when all hard exposed
surfaces are protected with proper mats.
Outdoor
• When setting up the equipment outdoors,
use a groundsheet to avoid damaging the
equipment.
• Do not expose equipment to heat, including
heat from exposure to the sun.
• Never leave equipment outside unattended
and keep the air pressure under the maximum
values found in this guide.
• Do not use the equipment in the rain or snow.
While inating equipment, electrocution may
occur and also the surface will be slippery which
can cause injuries.
• The equipment is not a otation device.
Maintenance
• Never pack, store or transport the equipment
when it is moist or dirty.
• The equipment can be cleaned with water and
soft soap. Do not use industrial cleaning
products.
• Do not use the equipment when it’s damaged,
leaking or when parts are worn or missing.
Warnings
• Be aware that our equipment is not designed as
a landing mat.
• Equipment may move during use which could
result in serious injury.
• Serious injury (including permanent paralysis
or death) could result from any activity involving
motion, rotation or height.
• All users of this equipment assume this risk of
serious injury.
• Mats cannot and do not eliminate hazards.
SAFETY RULES

8SPORTS www.airtrackfactory.com - [email protected] - Tel. [phone]
The thickness of our equipment has an e ect on how the equipment can be used. Most of our
equipment for home use is 10 cm thick. This goes for the AirFloors, AirBeams, and AirBoards.
When our equipment is 10 cm thick the pressure in the equipment needs to be high enough to
prevent you from hitting the  oor. You can  nd the recommended pressures on page six, but in the
end it’s up to the users’ preferences.
When rolling up the AirBeam, make sure that the center line is facing down!
!
, make sure that the center line is facing down!
SETTING UP & PACKING UP

9www.airtrackfactory.com - [email protected] - Tel. [phone]
Make sure the adapter is placed on the hose properly (4) and the blower or footpump is set to in ate (1,3).
Open the grey valve by twisting it to the left (6). Make sure the pin inside the valve is pressed out (8).
Attach the blower by twisting the adapter to the right (10) and turn on the blower. Your equipment should
start in ating. When fully in ated remove the hose. The equipment should not release air. (13)
Check the pressure with the manometer (optional) or jump on the equipment to test if the pressure is up
to your standards. If so, close the grey valve (15). Check the pressure before each training.
SET-UP
PACK UP
De ate the equipment by simply pressing the pin inside the grey valve. The equipment should de ate.
Roll up the equipment and store it. To completely de ate the equipment, the blower and foot pump can
be set to de ate. This way the equipment will become completely  at.
When rolling up the AirBeam, make sure that the center line is facing down!
1
5
9
13
17
21
2
6
14
18
22
3
7
11
15
19
23
4
8
12
16
20
Foot pump OV10 blower
10

10 SPORTS www.airtrackfactory.com - [email protected] - Tel. [phone]
Does your equipment seem to be leaking?
Make sure all valves are closed properly. The pin inside the grey valve are often left open (pin in)
when the cap is closed, which means the valve will still be leaking air. Always make sure the valve is
closed (pin out) before closing the valve. Still leaking? Check our FAQ.
Can’t t the equipment in the bag?
When rolling up the AirBeam, make sure that the center line is facing down!
We recommend using the blower to get the last bits of air out of the equipment. Our blowers have
an input and an output vent. One for inating and one for deating. For deating, connect the
blowers’ adapter to the input (IN) side of the blower and deate untill the equipment is completely
at.
When I detach the blower from the equipment all the air goes out.
Make sure the pin inside the valve is closed (pin out) before attaching the blower. The pin should
remain closed (pin out) during ination and usage. Only open the valve (pin in) when adjusting
pressure or deating.
HELP!

11www.airtrackfactory.com - [email protected] - Tel. [phone]
How long does it take to inate the equipment?
With the foot pump, equipment can be inated within minutes. Using our OV10 blowers greatly
speeds up the ination process.
Is there a chance of damaging the equipment by over pressurizing it?
No, the extreme pressure needed to actually damage our equipment cannot be reached with the
blowers we supply. Do not use any blowers or compressors not supplied by AirTrack Factory or one
of its distributors to inate our equipment.
24 Hours after ination the AirTrack is soft.
AirTracks are not designed to maintain their pressure overnight. Dierences in temperatures
and weather inuence the pressure inside the equipment. Make sure to set the pressure to your
preferences before each training. If you have any doubts, feel free to contact us for a professional
opinion.
What is the lifespan or your equipment?
Obviously this will depend on how our equipment is used and in what frequency. A lifespan of more
than 7 years is denitely not uncommon.
What guarantees do you give on your equipment?
We give a 5 year guarantee on our equipment. The customer is responsible for delivery to, and
pickup from, AirTrack Factory. Please check our terms of delivery for more detailed info.
When my equipment is leaking, how can you help us?
First of all, check if all valves are properly closed. If a valve is leaking, please contact us.
A puncture in the surface or damage to a seam could cause your equipment to leak.
For both options we have a solution that is both simple and cheap. You do not have to send the
equipment back to us; we will send the repair material to you or assist you in purchasing it locally.
Repairs take no longer than 10 minutes.
F.A.Q.

AirTrack Factory
Bijsterhuizen 1178
6546 AS, Nijmegen
Netherlands
[phone]
[email protected]