Airwell DLV007 User manual

INSTALLATION MANUAL
SAFETY PRECAUTIONS
● Readthefollowing"SAFETYPRECAUTIONS"carefullybeforeinstallation.
● Carryouttestrunningtoconrmthatnoabnormalityoccursafter the installation.Then,explaintousertheoperation,careandmaintenance asstatedin
instructions.Pleaseremindthecustomertokeeptheoperatinginstructionsforfuturereference.
Thisindicationshowsthepossibilityofcausingdeathorseriousinjury.
WARNING
Thisindicationshowsthepossibilityofcausingharmordamagetheequipment.
CAUTION
WARNING
1)Usequaliedinstallerandfollowcarefullythisinstructions.Otherwiseitwillcauseelectricalshock,waterleakage,orestheticproblem.
2)Installatastrongandrmlocationwhichisabletowithstandtheset'sweight.Ifthestrengthisnotenoughorinstallationisnotproperlydone,theset
willdropandcauseinjury.
3)Forelectricalwork,followthelocalnationalwiringstandard,regulationandthisinstallationinstruction.Anindependentcircuitandsingleoutletmust
beused.Ifelectricalcircuitcapacityisnotenoughordefectfoundinelectricalwork,itwillcauseelectricalshockorre.
4)Usethespeciedcableandconnecttightlyforindoorconnection.Connecttightlyandclampthecablesothatnoexternalforcewillbeactedonthe
terminal.Ifconnectionorxingisnotperfect,itwillcauseheat-uporreattheconnection.
5)Wireroutingmustbeproperlyarrangedsothatcontrolboardcoverisxedproperly.Ifcontrolboardcoverisnotxedperfectly,itwillcauseheat-up
atconnectionpointofterminal,reorelectricalshock.
6)Whencarryingoutpipingconnection,takecarenottoletairsubstancesotherthanthespeciedrefrigerantgointorefrigerationcycle.Otherwise,it
willcauselowercapacity,abnormalhighpressureintherefrigerationcycle,explosionandinjury.
7)Donotdamageoruseunspeciedpowersupplycord.Otherwise,itwillcausereorelectricalshock.
8)Thisequipmentmustbeearthed.Itmaycauseelectricalshockifthegroundingisnotperfect.
9)Donotinstalltheunitatplacewhereleakageofammablegasmayoccur.Incasegasleaksandaccumulatesatsurroundingoftheunit,itmay
causere.
10)Pleasediconnectthepowersupplywheninstallormaintenanceorsevicethissystem.
CAUTION
1)Selectionoftheinstallationlocation.
Selectainstallationlocationwhichisrigidandstrongenoughtosupportorholdtheunit,andselectalocationforeasymaintenance.
2)Donotreleaserefrigerant.
Donotreleaserefrigerantduringpipingworkforinstallation,reinstallationandduringrepairingarefrigerationparts.Takecareoftheliquidrefrigerant.
itmaycausefrostbite.
3)Itmayneedtwopeopletocarryouttheinstallationwork.
4)Donotinstallthisapplianceinalaundryroomorotherlocationwherewatermaydripfromtheceiling,etc.
5)Carryoutdrainagepipesasmentionedininstallationinstructions.Ifdrainageisnotperfect,watermayentertheroomanddamagethefurniture.
PartNO.IM.DLV1_A.1GB
MODELS
Ducttypeairconditioner
DLV007DLV009
DLV012DLV015
DLV018DLV021
DLV024

Unit:mm
Requiredtoolsforinstallationworks
NO. Tool NO. Tool NO. Tool
1Screwdriver 5Pipecutter
9
Torquewrench
18Nm(1.8kgf.m)
45Nm(4.5kgf.m)
65Nm(6.5kgf.m)
75Nm(7.5kgf.m)
2Electricdrill,holecore
drill(60mm) 6Reamer
3Hexagonalwrench 7Knife
4Spanner 8Measuringtape
Attachedaccessories
No. Accessoriespart Qty. No. Accessoriespart Qty. No. Accessoriespart Qty.
1
Centralcontrol
display(optional) 1 3
Draintube+clips
1 5
Unitoperationmanual
Installationmanual 2
2
Tie-Waps
6 4
Screwswasher
dowels 5 6
Gastubinginsulation
1
1SELECT THE BEST LOCATION
Whileselectingaplacefortheindoorunit
Allowmax.airowtothedesirespace.

Allowmaxreturnairow.

Ensureadequatedrainageofcondensedwater.

T
hedistancebetweenair-conditionerandobstaclesshouldmeetstherequirmentsinbelowg.
Leaveaminimum250mmfreespaceinfrontofthelter.

Allowafreeserviceaccesstoelectricalbox.

Alloweasyaccesstothebaseoftheindoorunitwhileprovidingenoughspacefromtheceiling.

Theinstallationheightshouldover2.3m.

2UNIT INSTALLATION
1.HOLESDRILLINGLOCATIONONTHECEILINGFORINDOORUNIT
Model AB
DLV007-DLV015 790 565
DLV018-DLV024 1090 565
2.DRAINAGEINSTALLATION
General
Foranefcientfunctioningofthedrainagesystem,pleasetakecareofthefollowing:
Alwaysbalancetheunitwith2downwardtothedrainagesideoftheunit.●
Use19mmtubedrainage.●
Itisrecommendedtoprepareadrainagepointbyprofessionalplumberclosetotheunit.●
Forproperdrainage,thepassagemustbeplannedwith1downslope.●
Preventanyupwardsorreverseowinanypart.●
Forpreventingofunpleasantsmellsintheroom,installasiphonintheinstallation.Installthedrainingtubewith6mmthicknesst● hermalinsulationsleeve.

Horizontaldrainage
Theunitincludesadrainpump,whichcanelevatecondensatewaterupto120cmfromtheunitlowestlevel.Thedrainagetubeisconnectedtotheupper●
drainagenozzle.
Thelowerdrainagenozzleroleistoemptythedrainpanbeforeservicingtheunit.●
Installonthedraintubewith5-10mmthicknessthermalinsulationsleevetopreventdrippings.●
Drainagetest
ForVRFsystempleasedodrainagetestafternishingallinstallations,wiringandpipingincluded,anddoingITEST(Installationtest)sucessfully:
(1)Poweronthesystem,andrunscoolingmode.
(2)Checkwhetherthepumpsoundisnormal.
(3)Slowlyinjectabout1,000ccofwaterintothedrainpan.Checkthedrainagethroughthetransparentdrainporttoseeifanydrainleakagehappens.
(4)Whenthecheckisnished,donotforgettocutoffthepowersupply.
3.UNITDIMENSIONS
Model ABC
DLV007-DLV015 750 696 790
DLV018-DLV024 1050 996 1090
4.ACCESSTOTHEUNIT
ΦLiquidPipe ΦGasPipe
DLV007 1/4" 1/2"
DLV009 1/4" 1/2"
DLV012 1/4" 1/2"
DLV015 1/4" 1/2"
DLV018 1/4" 1/2"
DLV021 3/8" 5/8"
DLV024 3/8" 5/8"
5.UNITINSTALLATION
Insert4M10or3/8threadsrodsintotheceiling.A.
Introducetherodsthroughtheslotsofunitsuspensionbrackets.B.
Positiontheshockabsorbers,addwashersandscrewthenutsuntiltheC.
unitisrmlysupported.
Incaseofagapbetweentheunitandtheceiling,putarubberoraD.
neoprenesheet.
565
Unit:mm

6.AIRFILTERLOCATION
Theairlterislocatedintherearsideoftheunit(defaultfromfactory)butcanbeeasilyrelocatedinthebottomoftheunitifitisrequired.
7.AIRFILTERCLEANING
Forcleaningthelterremoveitbypushinguptowardthebackoftheunitandpullitoutasdescribedbelow.
8.AIRFILTERRELOCATION
Removeairlterfromtheunit.1.
Removepanel4.2.
Removeltertrails2-3.3.
Insertltertrails2-3ontheoppositesideoftheunit.5.Closepanel4inthe4.
rearsideoftheunit.
Insertthelterintothetrails.5.
3DISPLAY CONTROL UNIT
1.LOCATIONCRITERIA
ItisrecommendedtoinstalltheDisplayControlUnitclosetoaceilinginacentralandneutralzoneattypicalconditions.Inaddition,the aesthetic aspect●
shouldbeconsidered.
TheDisplayControlUnitisconnectedtothemaincontrolboardontheairconditioner(theindoorunit)byacommunicationcable.Cableisconnectedtothe●
DisplayControlUnitbyaquick-connector.(8pinplug)
2.INSTALLATIONOFDISPLAYCONTROLUNITONWALL
Drilla12mmdiameterholeonthewall,forroutingthecommunicationcable.●
Opentheunitcover,drill3holesinthewalltomatchtheholesintheDisplayControlUnit,installtheinsertsandfastentheunittothewallwith3screws.●
TheDisplayControlUnitisprovidedofaspecialcommunicationcable,7meterslong,terminatedbyaplug,connectedinthehousingitselftoadistribution●
box,whichenablesthecontroloftheairconditionerfromseveraldifferentrooms,eachonefromitsownDisplayControlUnit.
Connectthequickconnectortotheappropriatesocketonthemaincontrolboardintheindoorunitelectricalbox.●
3.CONSIDERATIONSINLOCATINGTHEREMOTECONTROLUNIT
a)LocatetheRemoteControlUnitinsuchawaythatwhenmountedonitssupportonthewall,itwillbeinlinesightwiththeDisplayControl
Unit(atlessthan8m).
b)ItisrecommendedtoestablishthenallocationoftheRemoteControlUnitonlyaftertherstoperation,assuringpropertransmissionand
receptionbetweentheRemoteControlUnitandtheDisplayControlUnit.
1.MainControlBoardonIndoorUnit.
2.DistributionBoard.
3.CommunicationCable.
COLORCHART
Conn.Point WireColor Conn.Point WireColor
1Blue 5Purple
2Green 6Yellow
3Black 7Orange
4Brown 8Red

4ELECTRICAL WIRING CONNECTION
1.POWERSUPPLYWIRING
Unscrewandremovetheelectricalbox.●
Connectthepowersupplywiringstothepowersupplyterminalblock.●
Whendoingthis,pressthepowersupplywiringunderthewireclip.●
UNOCCUPIED DRY CONTACT
COMMUNICATIONWIRE
PROWER SOURCE WIRE
WINDOWS DRY CONTACT
ELB:ElectricityLeakageBreaker.
AH:Assistantheater.
PowerSupply
MainBusR/CWiring
2.MAINBUSANDR/CCOMMUNICATIONWIRING
Unscrewandremovetheelectricalbox.●
ConnecttheR/CwiringstoR1,R2terminalblockandthemainbuswiringstoF1,F2terminalblock.●
Pressthewiringsunderthewirecliptightly.●
3.TIGHTENINGTORQUEFORTHETERMINALSCREWS
Usethecorrectscrewdriverfortighteningtheterminalscrews.●
Ifthebladeofscrewdriveristoosmall,theheadofthescrewmightbedamaged,Andthescrewwillnotbeproperlytightened.Iftheterminalscrewsare●
tightenedtoohard,screwsmightbedamaged.
Refertothetablebelowforthetighteningtorqueoftheterminalscrews.●
Terminal Size Tighteningtorque
Terminalblock(total9pins) M4 1.2~1.5N.m
4.ELECTRICALCHARACTERISTICS
Unit Powersupply Fanmotor
MCA: Min.CircuitAmps(A)
MFA: Max.FuseAmps(A)
KW: FanMotorRatedOutput(KW)
LA: FullLoadAmps(A)
Model Hz Volts MCA MFA KW FLA
DLV007
50 220~240
0.64 16 0.12 0.38
DLV009 0.64 16 0.12 0.38
DLV012 0.64 16 0.12 0.38
DLV015 0.64 16 0.12 0.38
DLV018 0.73 16 0.14 0.45
DLV021 0.73 16 0.14 0.45
DLV024 0.73 16 0.14 0.45
Alleldsuppliedpartsandmaterialsandelectricsworksmustconformtolocalcodes.

Usecopperwireonly.

Allwiringmustbeperformedbyanauthorizedelectrician.

Everyindoorunitmusthaveasubcirclebreakerandthewholesystemmusthaveamaincirclebreaker.

Besuretogroundtheairconditioner.

Theapplianceshallbeinstalledinaccordancewithnationalwiringregulations,andshallbeprovidedtoensureall-poledisconnectionfromthesupplymains,

anddistancebetweenthepolesshallbemorethan3mm.

5.SPECIFICATIONSFORFIELDSUPPLIEDELBANDWIRE
Model Powersupplywiring RemotecontrollerwiringTransmission
wiring
FieldELB WireandSize wires Size
DLV007
16A
Mustcomply
withmaximum
currentandlocal
codes(≥0.75mm2)
Twisted-pairWire ≥1.0mm2
DLV009
DLV012
DLV015
DLV018
DLV021
DLV024
6.HEIGHTCOMPENSATIONSETTING
TheCompensationsettingaccordingtoinstallationheightcanbedonebyusingthedipswitch11and12oncontrollerPCB.
InstallationHeight HeightCode DS11 DS12
2.3-2.7(m) H0 OFF OFF
2.7-3.1(m) H1 OFF ON
3.1-3.5(m) H2 ON OFF
3.5(m) H3 ON ON
Note:Pleasedisconnectthepowersupplywhenchangethissetting.
Ifyoufeeltoonoisy,pleasesetDS11andDS12tolowerheightcodelevel.
CHECK ITEMS
BEFOREPOWERON
Isthereanygasleakageatarenutconnections?
⿌
Hastheheatinsulationbeencarriedoutatarenutconnection?
⿌
Istheconnectingcablebeingxedtoterminalboardrmly?Istheconnectingcablebeingclampedrmly?
⿌
IsthedrainageOK?(Referto"Checkthedrainage"section)
⿌
Istheearthwireconnectionproperlydone?
⿌
Istheindoorunitproperlyhookedtotheinstallationplate?Isthepowersupplyvoltagecompliedwithratedvalue?
⿌
AFTER POWER ON
Isthereanyabnormalsound?
⿌
Isthecoolingoperationnormal?
⿌
Isthethermostatoperationnormal?
⿌
Istheremotecontrol'sLCDoperationnormal?
⿌