AIS LRMOD1 User manual

WWW.AISINTERFACE.COM
TECH SUPPORT 833-AIS-TECH
Toll Free 800-365-6060
LRMOD1
REAR CAMERA INTERFACE FOR
SELECT LAND ROVER

Applications
LRMOD1
Parts inside the box
WWW.AISINTERFACE.COM
FEATURES:
• ADDS REAR CAMERA INPUT
• VIDEO IN MOTION
WARNING
RADIO MUST HAVE THE VERSION 2 FACTORY
NAVIGATION AND TOUCHSCREEN IN ORDER
FOR THIS PRODUCT TO BE COMPATIBLE.
2010 - 2012 Land Rover Discovery (L319)
2010 - 2011 Range Rover Sport (L320)
2010 - 2012 Range Rover Vogue (L322)
Navigation Touch-screen navigation system- version 2
LRMOD1
TECH SUPPORT 833-AIS-TECH
Video in Motion
The video-in-motion can be activated and deactivated by Dip 1 or al-
ternatively by the included loose green cable in connection with a
switch (not included in delivery).
Video-in-motion permanent With dip1 to ON the video-in-motion
function is activated permanently without disturbing the navigation
performance.
Video-in-motion selective With dip1 to OFF the included green cable is
used to activate the video-in-motion function.
Connect a switch to the green cable and connect the green cable to
+12V ACC.
• +12V = TV-Free is activated
• ● 0V = TV-Free is not activated
Note: The loose white cable is not required and must be isolat-
ed.
• Operation voltage 10.5 – 14.8V
• Stand-by power drain <2mA
• Operation power drain ~60mA
• Power consumption ~0,08W
• Temperature range -30°C to +80°C
• Weight 44g
Specifications

LRMOD1
WWW.AISINTERFACE.COM
Wiring the Interface
1.Connect female 8pin Molex connector of harness to male 8pin Molex
connector of CANbox.
2.Transfer female system-connector of vehicle harness from rear of
radio module into male system-connector of harness.
3 Plug female system-connector of into male socket on the rear of
radio module.
Switch off ignition and disconnect the vehicle’s battery! If according
to factory rules disconnecting the battery has to be avoided, it is
usually sufficient to put the vehicle in sleep-mode. In case the sleep-
mode does not show success, disconnect the battery with a resistor
lead.
Place of installation is on rear of the radio module and behind the
factory navigation monitor.
On Range Rover Vogue the radio module is a hide-away box which is
located behind the glove box.
On Range Rover Sport and Discovery 4 the radio module is located
behind the factory navigation monitor.
LRMOD1
TECH SUPPORT 833-AIS-TECH
Legal Information By law, watching moving pictures while driving is
prohibited, the driver must not be distracted. We do not accept any
liability for material damage or personal injury resulting, directly or
indirectly, from installation or operation of this product. This product
should only be used while standing or to display fixed menus or rear
-view-camera video when the vehicle is moving, for example the
MP3 menu for DVD upgrades.
• With dip1 to OFF the included green cable is used to activate the
video-in-motion function
Note: Dip switch functions:
• Dip 1 – activation TV-free
• Dip 2 – rear-view camera existing
• Dip 3 – TV icon simulation
• Dip 4 – no function
• Dip 5 – termination resistor CAN-Bus
• Dip 6 – termination resistor CAN-Bus
Setting dip 2 to ON codes the factory rear-view camera input which is
located on the brown Fakra male connector of the factory monitor.
When reverse gear is engaged, the navigation will automatically
switch to this input. On vehicles with factory rear-view camera set Dip
2 to ON, too.
Setting the DIP Switches

Wiring Diagram and Installation
LRMOD1
LRMOD1
TECH SUPPORT 833-AIS-TECH
• Pin 2: Video-signal rear-view camera
• Pin 5: Video-signal ground rear-view camera
CAMERA PIN Assignment 6pin male port of the monitor
Pin colored video-signal (black video-signal ground) with bare con-
tact of adapter CAB-LR10-R into pin 2 (pin 5) of the female grey-
red 6pin connector. Use red front is to lock the pins in the connect-
or.
Connect female grey-red 6pin connector to 6pin male port of the
monitor.
Connect the video RCA of the rear-view camera to female RCA con-
nector of adapter CAB-LR10-R.
Wiring Diagram and Installation