Akiles VersaMac+ User manual

Semi Automatic Desktop Punching And Ejector Machine
2015
Apr

8
13
Collecting Unit Setup
Changing of Punch Die
Troubleshooting 11
Warranty Policy
Assembly & Safety lnstructions

2015
Punch Unit
Mode Switch Button
Paper Jam Indicator
Die Set Channel
Cable Socket For Auto Feeder
Power Cord Socket For Auto Feeder
1
2
3
4
5
1 2 3
5
4
Paper Chip Container
Paper Holder
X4
Apr

22015
Side Guide
of Stooper
Guide B
Paper Delivery Track
Guide A
Signal Connecting Cable
Guide B
Guide C
Guide A
Stacker Unit
Allen Key Wrench #8
E
E
A. Screw Locker for Side Guide
B. Micro-Adjusted Knob for Side
Guides
C. Arrow for Side Guide
D. Punch Ruler Guide
E. For 3R、31M Punchdie
A
BB
B
C
D
E
1
2
Apr

2015
3
3.
4.
5
5.
oot Pedal
1
3 4 5
Apr
2
Stacker Unit
Punch
by One Person
2. Connect the Punch Unit and Collecting Unit by locking 3 screws and attaching the
connection cable.
2
8.
9.
10.
6.
7.
11. Never fix the by hand without powering off the unit and unplugging the power cord.
12. Turn off the power of before changing dies or maintaining the machine.
13. Punched sheets are delivered from the stacker unit to the collecting unit. Be reminded
to keep fingers, hair, jewelry, neckties, and other loose clothing or objects away from the
delivery trail.

42015
3. More punch patterns may be available.Contact your dealer for our most up to date list of
punch patterns.
Apr

52015 Apr
5. Make the appropriate adjustment to select the Depth Margin position best suited for your
job. There are 4 available depth margin positions in each punch die (2mm, 3mm, 4mm
and 5mm from edge of paper to the nearest edge of hole).Adjustments can be done by
PULLING or PUSHING the Depth Margin Control Bar towards the LEFT or RIGHT side
of the machine.See Picture 4

62015
To avoid partially punched holes,follow the simple steps below to disengage (remove)
the corresponding punch pin in the die set.
For most standard sheet sizes,you can easily find the holes that need to be disengaged
(removed) from the Punch Ruler Guide label on each die. Just look for the sheet size that
you are using, and identify the appropriate punch pin that will create a partial punched hole
in your sheet. See examples below
Apr

72015
See Picture 1
See Picture 2
See Picture 3
1
2
3
.
Apr
B
A
C
power
LED
mc
p
Line up here
for 14”punch.
Line up here
for 41 OVAL punch.
3. Press ”mode” button at
manual control panel
to select the preferred
mode.
If the paper chip container
overflows, the punch die or
the machine may be damaged.
1.5mm Thickness
Micro-switch
Punching Modes
Auto Mode : Insert sheets
into the punch throat from
right-hand side of the
machine, then slide it
towards the left to activate
the automatic punching and
paper ejection.
Foot Pedal Mode:
Activate the punching and
paper ejection by stepping
on the foot pedal.
See Picture 4 4
Paper Chip Container
Punch Only Mode:
Activate the punching
action by stepping on the
Foot Pedal. Paper will not
be ejected.
Maximum single punch
capacity of 25 sheets
(20 lb paper). The number
of sheets depends on the
3R、31M Punch die

8
1. position guide a.b by different sheet
size .
2015
2. Lift paper delivery guide.
3. Adjust paper stopper to match the
size of the punched paper.
4. Pull out the guide C when punching
A4 size sheets.
Guide B
Guide A
Paper Stopper
Guide C
Paper Delivery Guide
A4
A4
A4
See Picture 1
See Picture 2
See Picture 3
See Picture 4
1
2
4
3
Apr
Stacker Unit Setup
A4