Akura ATL1930W-HD User manual

Customer Help Line: 01422 263313
Opening Hours: Mon-Fri 8am-8pm, Sat 9am-4pm, Sun 11am-4pm
Or visit our website at www.ekey.co.uk
ATL1930W-HD

Specifications
3
3
4
4
5
5
6
7
8
9
9
10
11
12
13
15
16
17
Trouble Shooting Guide

2

Power HDMI VGA SCART S-Video Video L(AV) R(AV) PC-IN HP RF

5
5

6

7
When the remote control batteries are exhausted do not
break open or throw on a fire.Contact your local waste
authority for disposal instructions

8
6 Press the VOL+ button to start Autosearch. The TV will start searching from the
lowest frequency. When it finds a station, it will automatically store this in the first
location and move to the next. When Autosearch is complete, the TV will display
the first station found. In most cases, the stored stations will not be in the correct
order, therefore you must use the "SWAP" function to change to the correct order.

HUE 0
9

HUE 0
Hue
Use the VOL+ and VOL- buttons to adjust the hue of the picture.(only used in NTSC
mode )
AUTO CONFIG
H-POSITION 0
V-POSITION 0
HDMI mode
AUTO CONFIG: Press the VOL+ button to have
the following settings configured automatically.
H/V-POSITION: Use the VOL+/- buttons to
adjust the position of the picture on the screen.
10

11

12

13
.In the UK “I” is used.
Eastern Europe.
“BG” for Western Europe, “DK”
To select a channel to be skipped use the VOL+and VOL- buttons.
Use theVOL+and VOL- buttons to turn the AFC (auto frequency control) ON or OFF
Use theVOL+ or VOL- buttons to adjust the fine tuning if you experience problems
another station.
with a weak signal or interference from
When Auto Search Tuning has taken place, the stations received will be in “found” order,
location 1. To place the stations in the correct order use the SWAP function.
Select FROM and use theVOL+ or VOL-buttons to locate BBC1, it is useful to have a
Select TO and use theVOL+ or VOL - buttons to select “1”
Select SWAPand pressVOL+. This will move BBC1 to location 1, however the screen will
Press VOL+ again to return to the SWAP menu.
Select FROM again and locate BBC2.
Select TO and adjust to “2” and select SWAP, pressVOL+ to swap the station.
When complete BBC1 should be in location“1”, BBC2 “2”, ITV “3”, CH4“4”, ITV 5 “5” other
choice.
thus BBC1 will not be in
current tv guide handy.
now display what was in location 1.
stations can be located to your

Press the VOL+ button to start Autosearch. The TV will start searching from the lowest
frequency. When it finds a station, it will automatically store this in the first location and
move to the next. When Autosearch is complete, the TV will display the first station found.
In most cases, the stored stations will not be in the correct order, therefore you must use
the "SWAP" function to change to the correct order.
14

HDMI
Use the VOL+/- buttons to select: OFF, LOW, MID, HIGH.
You can select language from: English, French, Spanish, German, Russian and
Italian.
TXT Language
Use the VOL+ and VOL- buttons to select the Teletext language.
TXT EAST/WEST
Use the VOL+ and VOL- buttons to select the area of Teletext.
ZOOM
Use the VOL+ and VOL- buttons to select the display mode of the screen.
15
GENERAL MENU
LANGUAGE ENGLISH
BLUE SCREEN ON
NOISE REDUCE OFF
INPUT SOURCE TV
TXT LANGUAGE Pan European
TXT EAST/WEST WEST
ZOOM 16:9
RESET

16
Trouble Shooting Guide
Should you experience problems, please consult the guide below before returning to point of
Symptom Possible fault Remedy
Dead. No led lit Power not connected Check the power supply module is
connected and turned on
Dead Led lit Red Set stuck in standby Press Power button on the Tv or
Remote Control
Back light off Tv faulty. Call Help Line
No picture. Led Green TV in PC mode Select TV or AV Mode
Set not tuned in TuneTv to a Local Station
Aerial nor connected Connect a good aerial signal
No picture. Blue Screen. Tv switched to AV or PC Select TV with handset
Poor Picture. Noisy or Ghosting Poor aerialsignal If using an indoor aerial you may need
an outdoor aerial fitted
Teletext missing words or breaking up As above As above
Volume turned down or muted (TV) Turn up the volume and check if Mute
“OSD” is shown.
No Sound AV or PC connection not made
correctly
Check all external connections and that
the “feed” is turned on
PC
PC Not connected toTv Checkconnections.
Display shows “No Signal” PC not set correctly to TV settings Enter the PC display setup section and
set the PC correctly
Picture Noisy or Jittering Tv not adjusted to PC correctly Enter TV PC Menu and select “AUTO”
see page 14
Picture not central As above Enter TV PC menu and select H/V
position. See page 11
No Sound in PC mode Check PC sound connection This is different from AV mode and
must be connected seperately
Remote Control
Out of range or objects in “site line” Move nearer, or move any objects in
“site line”
No, or intermittent Remote Control
Batteries low Replace batteries every 6 months

Specifications
TV
TV System PAL BG/DK/I SECAM BG/DK
Screen size 19 "(diagonal)
Resolution 1440 x 900 pixels (RGB)
VGA suggest Mode 1024x768 60Hz
Contrast ratio 500:1
Brightness 300cd/m*2
$HULDOLQSXW XQEDODQFHG
Audio output power 2x3 W
Mains power 12V 5A
Power consumption 60W
Remote control
Type infrared
Control distance 5 m
Control angle 30° (horizontal)
Batteries 2 x 1.5 V, size AA
Dimensions 48 x 168 x24 mm
:HLJKW JZLWKRXWEDWWHU\
17