Akura APLDVD2YR2268VH User manual

GETTING STARTED
1. Please read the safety section (page 2) in the main instructions before proceeding further. This section
contains vital information to ensure safe positioning and use of the TV
2. Unpack the TV and place on a flat level surface suitable to support the weight of the TV (5.68 kg approx.).
3. Connect the aerial into the TV Tuner connector at the left side of the TV (Fig 1).
Fig.2 Fig.3
4. Connect the mains power lead to the Power Input socket at the rear of the TV,
(Fig 2) Plug in and switch on at the mains. The LED indicator on the TV will
illuminate and show red (Fig 3).
5. Open the battery compartment cover (Fig 4) on the reverse of the remote
control. Insert 2 x AAA 1.5V alkaline batteries in accordance with the diagram in
the battery compartment. Take care to observe the correct polarity (+/-).
6. Press the POWER button (Fig 5) to turn the TV set on. The LED indicator will
turn green and after a few seconds, the screen will activate and the first time
installation menu (Fig. 6) will appear.
7. Use the cursor ▼/▲buttons on the remote control to move up and down the
display to highlight desired options.
8. The default language is “English” if you want another language select that
language using the ►/◄buttons. Use the ▼/▲buttons to select “COUNTRY”
and use the ►/◄buttons to select another country if required. (If using in the
Rep of Ireland, select Belgium). Use the ▼/▲buttons to select “Tune Type” and
use the ►/◄buttons to select either ATV, DTV or ATV-DTV. (ATV-DTV is
default. If using in the Rep of Ireland, select ATV).
9. Press Ok. Fig 7 will be displayed. The TV will now search the entire UHF range
for both Digital and Analog TV stations. When search is complete the TV will
display the first channel (BBC1) in DTV mode. To view a list of received stations
press “LIST”, “Fig 8”. The Analog stations may not be in the correct order, see
page13 in the Main Instruction book for more information.
10. To select a channel either enter the number of the channel using the number
buttons on the remote control or scroll through the channels using the channel
CH+/- buttons.
11. To view analogue TV channels press the SOURCE/INPUT button to display the
source menu “Fig 9”. Using the cursor ▲/ ▼buttons highlight TV on the menu
and press OK to select. To view digital TV channels select DTV on this same
menu.
Fig.4
Fig 1
Fig.6
Fig.7
Fig.8
APLDVD2YR2268VH
MSD306
Quick Start Guide
Fig.5
Fig.9

For advanced operation of this TV please consult the Instruction Manual.
Should you have difficulty in operating this unit, please consult the Trouble Shooting Guide in the Instruction Manual.
If you suspect a fault, please contact the Customer Help Line.
WATCHING TV (basic operation)
12. Adjust the volume to the desired level using the volume button on the TV or Remote control. The sound can be
silenced by pressing the MUTE button on the remote control and a mute symbol will appear on the screen. Press the
MUTE button a second time to restore the sound.
13. To switch off the TV for short periods, press the POWER button. The TV will go into standby mode and the LED
indicator will change to red. If not using the TV for extended periods turn off at the mains switch to conserve
electricity, all settings will be retained.
DVD Operation
14 To select DVD operation press the SOURCE button to display the source menu. Using the cursor ▲/ ▼buttons
highlight DVD on the menu and press OK to confirm.
15 Place a DVD or CD-R disc into the slot on the side of the Tv. The disc must have the Label side facing you and the
Mirror side facing away. Do not handle the disc surface . Push the disc in gently and it will load automatically.
16 The disc will now start to be “Read” and then, depending upon the type of disc, will play or display the disc menu or
disc contents. Select the item you wish to view, using the navigation buttons on the remote control and press “OK”.
17. To manually control DVD play you can use the control buttons located on the side panel (Fig 10).
1. Press to insert or eject disc from player.
2. Press. to play and pause disc. If paused press to restart playing.
3. Press to Stop disc playing.
For all other DVD functions use the Remote Control
18. When you wish to remove a disc, press STOP and then EJECT. Do not grip the disc to pull it out of the player, wait
until the disc stops moving before gripping the disc outer and removing carefully. See page 27 in the main manual
for correct handling of discs.
Flat Screen
Although the Flat screen is made with high precision technology and 99.9% or more of the pixels are effective, dots may
appear. These can be black or bright dots (red, green or blue) and may appear constantly on the Flat screen. This is a
structural property of the Flat panel and is not a malfunction.
Fig.10
Label Side

Base fitting and removal.
Apply the base plate to the base mounting and fit the four screws provided. Tighten the four screws using a “Posi No 1”
screwdriver.
To fit the base plate.
Place the TV face down on a suitable surface with the base mounting facing you (Fig 1).
Fig 1
To mount the TV on a wall you need to purchase a VESA Standard (100mm) bracket.
Remove the screws as shown above.
Mount the wall bracket as described by the manufacturer.
Mount the TV to the wall bracket using 4 x 4mm x 10mm set screws. (Do NOT use longer screws as the internal parts of
the TV may be damaged).
Akura accepts no responsibility for damage, caused to or by, incorrect mounting of the wall bracket.
There are many variations of Wall Mounting Brackets.
The “ARM” variety allow a greater movement of the TV into the viewing angle required.
The “Fixed Tilt” variety allow up and down Tilt.
The Fixed “Non Tilt” variety are fixed very close to the wall. To ensure suitable clearance of the Mains Plug, 4 x spacers
are provided. Attach these to the TV cabinet back and tighten before fitting the Wall Bracket plate.