AL’S GARDEN ART AG-136 User manual

CARE AND MAINTENANCE
• Periodically, your light may require cleaning for
optimal performance.
• Cleaning should only be done with warm soapy
water. Be sure to use biodegradable soap.
• The frequency of cleaning depends upon the
conditions of the environment where light is
used.
• This light is designed to operate at
temperatures between 20ºF and 110ºF.
REPLACING THE LENS OR BULB
Replacement for the high intensity halogen bulb
AG-85 type MR11 bulb/reflector.
The bulb is not under warranty
1Unplug the transformer
2Remove the light’s cable from the transformer
and allow the light to cool before replacing bulb.
3Remove the lens retainer by pushing the
retainer down and turning counter-clockwise.
4Remove the lens and unplug the bulb/reflector
from the socket.
5Press the new bulb into the socket and place
back into the light housing. Do not touch the
lamp at any time as oil from skin may damage
lamp. Use a soft cloth.
6Re-install the lens and lens retainer ensuring
that the o-ring remains seated in the o-ring
groove. Do not operate the light fixture with a
missing or damaged lens.
REPLACEMENT PARTS LIST
Part No. Description
A AG-81 Submersible Light
12V/10W with 16 foot cord
B 12V/10W Transformer
Included only with AG-83
C AG-84 Colored Lens Pack
For replacement parts, contact our customer
service department at 909-424-0221.
8:00 am – 4:30 pm PST, Monday through Friday.
TROUBLESHOOTING
• If lights fail to illuminate, check that lights are
getting power by testing another appliance in
the same power outlet.
• If the light will not illuminate, follow the
instructions for “Replacing The Bulb”.
Single Light Kit
1 Light with 12V/10W
Transformer
model AG-136
PACKAGE CONTENTS
Part Description Qty
AG-81 Single Light w/o Transformer 1
AG-84 Colored Lens Pack 1
12V/10W Transformer
Questions, problems, missing parts?
Before returning to your retailer, contact ou
r
customer service department at 909 424-0221
8:00 am – 4:30 pm, PST, Monday - Friday, or
e-mail us at [email protected]
AL’S GARDEN ART
Manufacturers of cast stone fountains an
d
statuary since 1949, family owned an
d
operated with more then half a century o
f
skill and passion for creating top quality cas
t
stone art.
P.O. Box 111 •Colton, CA 92324
www.alsgardenart.com
Open
Close
B
Clear Lens
To change the color of the light replace clear lens
with one of the AG-84 colored lenses.
AG-85 Light Bulb
A
C

WARNINGS AND CAUTIONS
WARNING
• Risk of Electrical shock. Install only to a
covered Class A GFCI receptacle that has an
enclosure that is weatherproof with the
attachment plug cap inserted or removed.
• Risk of Electrical shock. Mount the unit at a
height greater than 1 foot from the ground
surface.
• Risk of Fire. Installation involves special wiring
methods to run wiring through a building
structure, consult a qualified electrician.
• Risk of electric shock, do not remove the cord
and strain relief.
• Do NOT submerge the Transformer.
• Risk of electrical shock – This submersible
light kit has not been investigated for use in
swimming pool or marine areas.
CAUTION
• This light kit has been evaluated for use in or
above water only.
• Use a proper power source as indicated on the
Transformer label.
• Keep the cord away from high temperatures or
other heat sources.
• TRANSFORMER CAPACITY: Make sure that
the total number of lights connected to the
Transformer does not exceed the transformer
10-watt output capacity.
• Do not use the light in water less then 50° F or
exceeding 104° F.
• Do not use with a dimmer.
• The light is not to be used in swimming pools or
spas.
• Lighted lamp gets hot quickly!
• Do not touch hot lens, guard or enclosure.
PREPARATION
Before beginning assembly or operation of
product, make sure all parts are present.
Compare parts with package contents list on the
cover and diagram on the reverse side of this
document. If any part is missing or damaged, do
not attempt to assemble, install or operate the
product. Contact customer service for
replacement parts.
• Estimated Assembly Time: 5 minutes
• No tools required for assembly.
LIMITED WARRANTY
This warranty is offered to you as an extra benefit
and does not affect your rights as a consumer in
any way. This unit has been checked for
compliance to performance requirements at the
time of manufacture and are made in accordance
with the requirements set forth in UL1310 to
insure safe operations over the life of the product.
This light is warranted against manufactured
defect for one (1) year from the date of purchase.
Proof of purchase is required for all warranty
claims. The warranty is not valid if defects are
caused by tampering, negligence, misuse or not
observing safety warnings. No responsibility is
assumed for indirect damage that may result from
the use of this appliance.
The warranty does not apply to or cover damages
or defects caused by external causes, including,
but not limited to, improper or faulty installation or
unauthorized modification, lightning, electrical
surges, abuse, misuse or abnormal use or
misapplication, including use in a manner
inconsistent with the product’s intended function.
The purchaser is responsible for determining the
suitability of the product for its intended use. If
products are damaged in transit, a claim should
be filed with the carrier.
This warranty does not cover the AG-85 high
intensity halogen bulb.
ASSEMBLY INSTRUCTIONS
1. (Fig. 1) Connect the light to the transformer by
pushing the plug into the transformer socket until
it is firmly seated. Hand tighten the nut from the
plug to the socket.
2. Place the light in or out of water. DO NOT
SUBMERGE the transformer.
3. (Fig. 2) Plug the transformer into a properly
grounded electrical outlet.
Fig. 1
Plug from
light
Fig. 2
Transformer
GFCI