AL’S GARDEN ART AG-80 User manual

CARE AND MAINTENANCE
• Periodically, your lights may require cleaning
for optimal performance.
• Cleaning should only be done with warm soapy
water. Be sure to use biodegradable soap.
• The frequency of cleaning depends upon the
conditions of the environment where lights are
used.
• These lights are designed to operate at
temperatures between 20ºF and 110ºF.
REPLACING THE LENS OR BULB
Replacement for the high intensity halogen bulb
AG-85 type MR11 bulb/reflector.
The bulb is not under warranty
1Unplug the transformer
2Remove the light’s cable from the transformer
and allow the light to cool before replacing bulb.
3Remove the lens retainer by pushing the
retainer down and turning counter-clockwise.
4Remove the lens and unplug the bulb/reflector
from the socket.
5Press the new bulb into the socket and place
back into the light housing. Do not touch the
lamp at any time as oil from skin may damage
lamp. Use a soft cloth.
6Re-install the lens and lens retainer ensuring
that the o-ring remains seated in the o-ring
groove. Do not operate the light fixture with a
missing or damaged lens.
REPLACEMENT PARTS LIST
Part No. Description
A AG-81 Submersible Light (4)
B AG-119 3-Way Connector
C AG-139 13-Foot 2-Way Extension
D Light Sensor
Only Included with AG-83
E AG-83 60Watt Transformer
F AG-84 Colored Lens Set (4)
For replacement parts, contact our customer
service department at 909-424-0221.
8:00 am – 4:30 pm PST, Monday through Friday.
TROUBLESHOOTING
• If lights fail to illuminate, check that lights are
getting power by testing another appliance in
the same power outlet.
• The light is designed to turn on when it gets
dark, and turn off when it gets light. To activate
the light during daylight hours, cover the sensor.
• If the light will not illuminate, follow the
instructions for “Replacing The Bulb”.
• If lights do not turn off during daytime, check
sensor. Make sure the sensor faces up and is
not covered by dirt or debris.
PREPARATION
Before beginning assembly or operation of
product, make sure all parts are present.
Compare parts with package contents list on the
cover and diagram on the reverse side of this
document. If any part is missing or damaged, do
not attempt to assemble, install or operate the
product. Contact customer service for
replacement parts.
• Estimated Assembly Time: 5 minutes
• No tools required for assembly.
Submersible
Light Kit
Four 12V/10W Halogen
Submersible Lights with
60W Transformer
and daylight off sensor
model AG-80
PACKAGE CONTENTS
Part Description Qty
AG-81 Single Light with 16-foot cord 4
AG-83 Transformer w/sensor 1
AG-84 Lens Set (Red, Blue, Yellow, Green) 4
AG-139 13-Foot Wire Extension 1
AG-85 Replacement Bulb 4
Questions, problems, missing parts?
Before returning to your retailer, contact ou
r
customer service department at 909 424-0221
8:00 am – 4:30 pm, PST, Monday - Friday, or
e-mail us at [email protected]
AL’S GARDEN ART
Manufacturers of cast stone fountains an
d
statuary since 1949, family owned an
d
operated with more then half a century o
f
skill and passion for creating top quality cas
t
stone art.
P.O. Box 111 •Colton, CA 92324
www.alsgardenart.com
Open
Close
C
A
D
E
F
B
Clear Lens
To change the color of the light replace clear lens
with one of the AG-84 colored lenses.
AG-85 Light Bulb

60 Watt Transformer
WARNINGS AND CAUTIONS
WARNING
• Risk of Electrical shock. Install only to a
covered Class A GFCI receptacle that has an
enclosure that is weatherproof with the
attachment plug cap inserted or removed.
• Risk of Electrical shock. Mount the unit at a
height greater than 1 foot from the ground
surface.
• Risk of Fire. Installation involves special wiring
methods to run wiring through a building
structure, consult a qualified electrician.
• Risk of electric shock, do not remove the cord
and strain relief.
• Do not remove the grounding pin from the
power cord plug.
• Do NOT submerge the Transformer.
• Risk of electrical shock – This submersible
light kit has not been investigated for use in
swimming pool or marine areas.
CAUTION
• This light kit has been evaluated for use in or
above water only.
• Use a proper power source as indicated on the
Transformer label.
• Keep the cord away from high temperatures or
other heat sources.
• TRANSFORMER CAPACITY: Make sure that
the total number of lights connected to the
Transformer does not exceed the transformer
60-watt output capacity.
• Do not use lights in water less then 50° F or
exceeding 104° F.
• Do not use with a dimmer.
• The light is not to be used in swimming pools or
spas.
• Lighted lamp gets hot quickly!
• Do not touch hot lens, guard or enclosure.
LIMITED WARRANTY
This warranty is offered to you as an extra benefit
and does not affect your rights as a consumer in
any way. This unit has been checked for
compliance to performance requirements at the
time of manufacture and are made in accordance
with the requirements set forth in UL1310 to
insure safe operations over the life of the product.
This light kit is warranted against manufactured
defect for one (1) year from the date of purchase.
Proof of purchase is required for all warranty
claims. The warranty is not valid if defects are
caused by tampering, negligence, misuse or not
observing safety warnings. No responsibility is
assumed for indirect damage that may result from
the use of this appliance.
The warranty does not apply to or cover damages
or defects caused by external causes, including,
but not limited to, improper or faulty installation or
unauthorized modification, lightning, electrical
surges, abuse, misuse or abnormal use or
misapplication, including use in a manner
inconsistent with the product’s intended function.
The purchaser is responsible for determining the
suitability of the product for its intended use. If
products are damaged in transit, a claim should
be filed with the carrier.
This warranty does not cover the AG-85 high
intensity halogen bulb.
ASSEMBLY INSTRUCTIONS
1. (Fig. 1) Using the 3-way adaptors and the 13-
foot 2-way extension cord connect all lights as
shown. Press each plug so it is firmly seated and
hand tighten the nut from the plug to each socket.
2. (Fig. 2) Connect the lights to the sensor by
pushing the plug into the sensor socket until it is
firmly seated. Hand tighten the nut from the plug
to the socket.
3. (Fig. 3) Connect the sensor to the transformer
by pushing the plug into the transformer socket
until it is firmly seated. Hand tighten the nut from
the plug to the socket.
4. Place the lights in or out of the water. DO
NOT SUBMERGE the transformer and sensor.
Make sure the light sensor faces up.
NOTE: At night, the lights will automatically turn
on. At sunrise, they will automatically turn off.
4. (Fig. 4) Plug the transformer into a properly
grounded electrical outlet.
2-way extension
cord (13-foot)
3-way
adaptor (2)
4 weighted watertight
submersible lights with
16-foot cords
Fig. 1
Fig. 2
Sensor
Plug from
lights
Fig. 3
Plug from
sensor
Photo-eye must face up
to receive light during
daytime
GFCI
Fig. 4