Oceanled DISCOVER D3 User manual

LIGHT. YEARS AHEAD. WWW.OCEANLED.COM
OceanLED MANUAL / DISCOVER D3 / REVISION 1
INSTALLATION & OPERATION MANUAL
DISCOVER D3

DISCOVER D3.
INSTALL & OPERATION MANUAL
1
Preface
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
CAUTION
(Risk Group 2): Possibly hazardous optical radiation emitted from this product. Do not stare at operating
lamp. May be harmful to the eye.
WARNINGS
Before installing your OceanLED Light, read and follow all warning notices and instructions which are
included. Failure to follow safety warnings and instructions can result in property damage, severe injury or
even death.
Before installing your OceanLED Light, check local laws for restrictions regarding the use of coloured lights
in your area.
Salt is an inherently corrosive material. Metal parts and certain natural and man-made surfaces are
particularly susceptible to corrosion and deterioration when used in and around salt water. Some OceanLED
lights contain combinations of plastic and polymer products which are impervious to saltwater corrosion,
however, screws and fasteners used for the installation must be of a marine grade type stainless steel or
equivalent and monitored annually to ensure the lights remain in service for years to come.
Discover D3 light is for mounting directly to a flat surface. Do not submerse your cable ends in water; cable
and connections exposed to underwater submersion will not be covered by warranty.
Never connect/disconnect lights with power applied as irreversible damage may occur. Ensure polarity of
power connections is correct. Failure to do this may invalidate warranty.
Though the Discover D3 has protection against temporary submersion, please ensure the rear of the light is
in a dry area and not subject to a wet environment, especially when installed. Failure to do this may invalidate
warranty.
Never Use Solvents! Cleaners, fuel, and other products that may contain strong solvents, such as acetone,
that attack many plastics greatly reducing their strength and irreversibly damaging the special lens coatings
and cable sheathings.
Never clean lights using a high-pressure jet wash –this will invalidate warranty. Please avoid coating the
front of the light/lens without consulting OceanLED. Failure to do so will invalidate your warranty.
DANGER
RISK OF ELECTRIC SHOCK OR ELECTROCUTION
This underwater light must be installed by a licensed or certified electrician in accordance with all applicable
local codes and ordinances. Improper installation will create an electrical hazard which could result in death
or serious injury to swimmers, installers, or others due to electrical shock, and may also cause damage to
property. Always disconnect the power to the light at the circuit breaker before servicing the light.

DISCOVER D3.
INSTALL & OPERATION MANUAL
2
Contents
Preface ..............................................................................................................................................................................1
1 Installation Checklist.......................................................................................................................................................3
2 Overview.........................................................................................................................................................................4
3 Preparing the Hull...........................................................................................................................................................5
4 Installation.......................................................................................................................................................................6
4.1 INSTALLING THE LIGHT FIXTURE.......................................................................................................................6
4.2 ELECTRICAL INSTALLATION (12/24V DC)..........................................................................................................9
4.3 FINALISING THE INSTALLATION.......................................................................................................................11
4.4 TEST YOUR INSTALLATION...............................................................................................................................11
5 Operation / Maintenance..............................................................................................................................................12
5.1 OPERATION .........................................................................................................................................................12
5.2 MAINTENANCE....................................................................................................................................................12
6 Troubleshooting............................................................................................................................................................13
6.1 TROUBLESHOOTING PROBLEMS AND THEIR SOLUTIONS.........................................................................13
7 Appendix.......................................................................................................................................................................15
7.1 OVERALL DIMENSIONS......................................................................................................................................15
7.2 DRILLING TEMPLATE..........................................................................................................................................15
7.3 CABLE GAUGE CHART 12V...............................................................................................................................16
7.4 CABLE GAUGE CHART 24V...............................................................................................................................17
8 Warranty.......................................................................................................................................................................19
PRETEST
Always test the lights prior to installation. Failure to do this may result in additional installation time and could invalidate
the warranty.
IMPORTANT NOTICE
Attention Installer: This manual contains important information about the installation, operation, and safe use of this
product. This information should be given to the owner and/ or operator of this equipment.
WARRANTY COVERAGE
Please refer to www.oceanled.com/downloads for full warranty statement.

DISCOVER D3.
INSTALL & OPERATION MANUAL
3
1 Installation Checklist
1. Decide on light spacing –OceanLED recommendations available.
Though the Discover D3 has protection against temporary submersion from inside the boat, please
ensure the rear of the light is in a dry area and not subject to a wet environment, when installed.
2. Ensure correct cable gauge is used (refer to relevant cable gauge chart).
3. Preparing the hull. Ensure hull thickness is below the maximum 50mm (2”).
4. Make sure the lights have been fitted following the correct orientation.
5. Correct marine sealant applied evenly around bezel.
Ensure fully watertight seal is created after sealant cures.
6. Correct fitting of light fixture onto hull. Never leave vessel unchecked for a few days after install.
Always check routinely for a few days after installation to ensure the install is correct and fully
sealed.
7. Test installation BEFORE entering water. Never connect/ disconnect lights whilst powered ON.
8. Troubleshooting if required - most issues can be resolved by following the guidelines.

DISCOVER D3.
INSTALL & OPERATION MANUAL
4
2 Overview
Product Overview
Power Source
Most installations will utilise on-board 12/24V DC power supply from a marine battery. However, if AC to DC power
supply is being used, please allow at least 15% reserve for voltage fluctuations due to variables beyond your control
such as ambient temperature and supply voltage fluctuations. This is to ensure your lights are always receiving the
proper voltage and to ensure the power supply is not “overloaded”, causing premature failure. Use chart below in
determining power supplies.
Power Consumption and Recommended Fuse values
Identifying your model
Discover D3 Ultra White
Discover D3 Midnight Blue
Model
Current @ 12V
DC
Current @ 24V
DC
Max Nominal
Power
consumption
15% reserve in
Watts
Recommended
fuse 12V/24V DC
Discovery D3
0.7A
0.37A
9W
10.3W
1.25A
Mounting Screws
Fuse Kit
Light Unit

DISCOVER D3.
INSTALL & OPERATION MANUAL
5
3 Preparing the Hull
The Discover D3 unit requires an additional 60mm / 2.36” free space from the rear of the light body to allow
for the cable clearance. (See overall dimensions in the Appendix).
Ensure that the part of the light inside the vessel has a diameter of 60mm/ 2.36”free space around it free from
any insulation material.
OceanLED recommends using a qualified installer / technician when making modifications to your vessel.
Please also consult the manufacturer for more detail on modifications and installation.
OceanLED recommends use of provided screws. If alternative screws are used, do not use counter sunk or
non-flat shoulder screws to secure your lights to the hull (failure to do so will invalidate your warranty).
If lights are assembled in a conductive or wooden hull suitable fastening (marine grade) need to be used. The
fastenings then should be bonded to the vessel cathodic protection system. Please contact OceanLED for
additional details.
For the correct orientation of the light the logo should face upwards and parallel with the water line. See
drilling template –in the Appendix, Chapter 7.
Depth/Spacing
Ideally mount your lights at similar depth levels to ensurematching colour consistency through the water. Deeper lights
will look duller and possibly differ in colour compared to shallower mounted units.
SPACING / INSTALL DEPTH
E2
Recommended Spacing
0.5-1.2m (2-4’)
Recommended Installation depth (From the light waterline)
150-200mm (6-8”)
Maximum Hull Thickness
Maximum hull thickness: 50mm (2”)
Hole Cut Out
Hole Cut out size - 44mm (1.73”)
Overall Dimensions
See overall dimension schematic –in the Appendix, Chapter 7.

DISCOVER D3.
INSTALL & OPERATION MANUAL
6
4 Installation
4.1 INSTALLING THE LIGHT FIXTURE
Additional items required not supplied by OceanLED:
•Marine sealant - 3M 4200 or equivalent
•Cable ties
•Waterproof Cable Connectors / Junction Box* (optional)
•Philips Screwdriver or Pozidrive #2 Screwdriver Bit
•44mm (1.73”) Hole Saw Cutter
•Drill Bit for mounting screw holes
*Optional 4-Way Junction box available from OceanLED. Please contact OceanLED or your representative for further information.
OceanLED recommends dry fitting all products. Before applying sealant, please ensure the surface is clean
of any dust, dirt or grease. When installing, be sure that the light fits the area and secures to the hull using
the appropriate hardware before applying any sealant.
When applying sealant to the light fixture, use OceanLED packaging material such as the light cardboard box
when placing the light on the ground face down to prevent damage/ scratch of the front bezel.
DISCOVER D3
Kit Includes
Discover D3
3x Mounting Screws

DISCOVER D3.
INSTALL & OPERATION MANUAL
7
Installation (Once hull preparation is complete)
1. Testlight(s) before fitting.
2. Apply marinesealant to therear of the front bezel to ensure acomplete unbroken seal around the light.
1. Start feeding the light cable through the hole. Ensure the correct orientation of the light unit with the logo
facing upwards and mounting holes aligning with the pre-drilled pilot holes.
2. Insert the light into the hull, pressing the light hard into the hull and twist slightly to spread the sealant
around behind the light to ensure goodadhesion.
Breakages due to lights falling out of the hull are NOT covered under warranty and can cause serious
bodily injury as can any falling object.
Marine Sealant

DISCOVER D3.
INSTALL & OPERATION MANUAL
8
3. Cover the screws threads with the sealant and screw into the pre-drilled pilot holes.
4. Tighten the screws with a hand tool ONLY! DO NOT over-tighten the screws, as you could damage the
front bezel, and will void your warranty.
5. Once you are satisfied that the unit is fully tightened, you will notice that sealant has squeezed out from
around the perimeter of the light. Using a cloth, wipe off excess sealant to leave a clean seal. If you do not
see sealant squeeze out from the body, you have not used enough sealant or possibly tightened the unit
enough to the hull. Carefully examine the installation to make sure the seal you have installed on the unit is
fully watertight. If in doubt, remove light, re-apply sealant and re-install.

DISCOVER D3.
INSTALL & OPERATION MANUAL
9
4.2 ELECTRICAL INSTALLATION (12/24V DC)
Additional items required not supplied by OceanLED:
•Junction box* / waterproofconnectors
•Sufficient cable to connect to DC PowerPack
*Optional 4-Way Junction box available from OceanLED. Please contact OceanLED or your representative for further information.
Always consult a qualified electrician when connecting OceanLED light fixtures.
When connecting light units, please note that all OceanLED lights will operate within a specific voltage range.
Please check the electrical information to ensure cable gauge follow the recommendations.
Never leave the bare cables unprotected. Take care to not leave the bare wire ends in bilge water before
making the waterproof connections. Water deposits in the connectors and cables will cause corrosion. Over
time water can also work its way into the unit along the inside of the cable due to capillary action causing the
light to fail. This will NOT be covered under warranty.
For complete instructions on DC connections, please refer to ABYC codes of practice and other applicable
codes and ordinates for DC connections.
Where multiple lights are fitted, and especially on 12V systems, it is advised to use a relay system to supply
the switched power to the lights, to reduce load on the switch and voltage drops caused by long cable runs
to the switch location.
1. Depending on the model and number of lights installed, you will need to pull the correct sized power cable from
the DC power source (breaker/fuse panel) to the light locations to supply constant power to the light units. It is
imperative that the correct sized tinned marine grade cable is used to avoid voltage drop issues.
See Chapter 7: Appendix for recommended cable gauges.
2. Using waterproof butt splices or IP66 waterproof junction boxes, make the connections at either end of the
system to attach the lights to the DC system. Make sure any heatshrink used completely encapsulates the
outer wire sheath (the use of glue-lined heat shrink is highly recommended to ensure water tightness).
Never install a new light fixture then leave the vessel in the water unchecked for several days.
3. It is imperative that either the OceanLED supplied fuse on each power line to eachlight or a suitable protection
device is used to protect the cable/light unit. Failure to do so will void the warranty. See table in Chapter 2:
Power Consumption and Recommended Fuse values. Make sure any heatshrink used completely
encapsulates the outer wire sheath (the use of glue-lined heat shrink is highly recommended to ensure water
tightness).
4. Securecablesensuringwhere the cableexits the lightit is not under undue stress.Finishand test the light units
BEFORE the vessel goes into the water.
Discover D3
Kit Includes
Fuse Kit

DISCOVER D3.
INSTALL & OPERATION MANUAL
10
Fuse Kit Connection Overview:
12/24V DC Connection Diagram:
+
-

DISCOVER D3.
INSTALL & OPERATION MANUAL
11
Wiring Schematic with Power Junction Box:
4.3 FINALISING THE INSTALLATION
The Discover D3 features a polymer front bezel that protects against corrosion as well as insulates against conductive
hull types. The front face of the bezelis pre-coated with a specialized Tritonium® coating which helps to prevent marine
growth from adhering to it. The light body is constructed from Hard Anodised Aluminium and does not require further
protection.
No paint or any type of anti-fouling agent should be applied to the bezel, as damage may occur to the
light due to chemical incompatibility and can affect the performance of the light and will immediately void the
warranty.
Please do not use any un-authorised cleaning products to remove excess paint or antifoul off the bezel.
OceanLED recommends using Isopropyl Alcohol (IPA) only.
4.4 TEST YOUR INSTALLATION
Always test the lights BEFORE the vessel goes back into the water. At this final stage make sure all of the system is
operational. If you have any issues, please contact your local OceanLED representative.
Never install a new light fixture then leave the vessel in the water unchecked for several days.
When the vessel is placed in the water, immediately check for leaks. Note that very small leaks may not be
readily observed. It is best not to leave the vessel in the waterfor more than 3 hours before checking it again.
If there is a small leak, there may be considerable bilge water accumulation after 24 hours. If a leak is
observed, youmust TAKE ACTION IMMEDIATELY to prevent damage.

DISCOVER D3.
INSTALL & OPERATION MANUAL
12
5 Operation / Maintenance
5.1 OPERATION
The Discover D3 light is available in either Midnight Blue or Ultra White models and therefore works only in standard
single colour power mode.
5.2 MAINTENANCE
Marine growth can build up quickly on the light and can reducethe performance injust a few weeks.
To help prevent this, all OceanLED lights have been coated with a specialized Tritonium® coating which helps to
prevent marine growth from adhering to the lens. Lights should be cleaned with a soft boat brush bi-weekly, or as
needed to keep the lens of the light clean.
Growth varies greatly around the world and maintenance is imperative to the proper operation and longevity of the
product. Ifheavy foulingoccurs,barnaclescanberemovedfromthe lensusinga plasticscraperand moderatepressure
underwater.If cleaning the lens while the boat is out of the water, wet the lens before scraping. Never scrape or try to
removebarnacles from a dry lens.

DISCOVER D3.
INSTALL & OPERATION MANUAL
13
6 Troubleshooting
6.1 TROUBLESHOOTING PROBLEMS AND THEIR SOLUTIONS
DISCOVER D3
PROBLEM
CHECK
CAUSE
FIX
Light does
not look
bright
Check that there is no marine
growth on the lens
Marine growth
Clean the lens as per
maintenance advice
Check voltage supply to the
light is between 11V and 32V
DC (The light will still work
between 9 and 11 volts however
at reduced brightness)
Voltage is either too
high or too low
Investigate reason for high or
low voltage and fix
Check voltage supply is stable
and does not fluctuate
Voltage is fluctuating
Investigate reason for voltage
fluctuation and fix
Check that the electrical
connections between the
light and the supply cable
have been made correctly and
recommended cable gauge has
been used
Poor electrical
connection
Remake connection and seal
joint correctly
Confirm all LEDs are illuminated
1 or more LEDs are not
working
Contact your dealer.
Check lights to see if water is
present inside the light
Water present
Contact your dealer.
Check cable connections for
corrosion
If corrosion is present
It is not advised to reuse the
cable if water is present inside.
Contact your dealer
for a replacement. This is NOT
covered by the warranty
Light has
water inside
Check connections to make sure
they are not submerged in water
Light will require
replacing
This is not covered by the
warranty
Check cable to make sure there is
no damage to the cable
Cable will require
replacing
This is not covered by the
warranty. Only use genuine
OceanLED parts
Checked all factors that are
above, and the light still does not
work
Light faulty
Contact your dealer for a
replacement light

DISCOVER D3.
INSTALL & OPERATION MANUAL
14
DISCOVER D3
PROBLEM
CHECK
CAUSE
FIX
Light does not
light up
Check that the electrical
connections between the light
and the supply cable have been
made correctly
Poor electrical
connection
Remake connection and seal
joint correctly
Check that the wiring polarity is
correct, red to positive and
black to negative
Polarity incorrect
Change the wiring polarity
and seal joint correctly
Check that there is power
supply to the light cable
connection
Poor electrical
connection
Trace the cables back,
checking at joints until break
has been located. Then rectify
the problem and seal joint
correctly
Check that the electrical
connections between the supply
cable and the light circuit
breaker or fuse have been
made correctly
Poor electrical
connection
Remake connection and seal
joint correctly
Check that the in-line fuse is
intact and not blown
Replace fuse
If fuse keeps blowing, then
there is a short circuit in the
light system that must be traced
and rectified. If no external short
can be located contact your
dealer
Check that the light supply
circuit breaker is closed, or the
fuse has not blown
Close circuit breaker /
replace fuse
If breaker / fuse keeps blowing,
then there is a short circuit in
the light system that must be
traced and rectified. If no
external short can be located
contact your dealer

DISCOVER D3.
INSTALL & OPERATION MANUAL
15
7 Appendix
7.1 OVERALL DIMENSIONS
7.2 DRILLING TEMPLATE
Print A4 at 100% for correct scaling.




DISCOVER D3.
INSTALL & OPERATION MANUAL
16
7.3 CABLE GAUGE CHART 12V
Supply & Return Cable Conductor Size Chart 3% drop for when using 12V DC supply
Cable
length
(feet)*
Circuit Current
2 Amp
4 Amp
6 Amp
8 Amp
10 Amp
15 Amp
20 Amp
25 Amp
30 Amp
40 Amp
50 Amps
0-5
18
AWG
18
AWG
16
AWG
16
AWG
14
AWG
12
AWG
12
AWG
10
AWG
10 AWG
8 AWG
8 AWG
5-10
18
AWG
16
AWG
14
AWG
12
AWG
12
AWG
10
AWG
8 AWG
8 AWG
6 AWG
6 AWG
4 AWG
10-15
16
AWG
14
AWG
12
AWG
10
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
4 AWG
2 AWG
15-20
16
AWG
12
AWG
10
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
20-25
14
AWG
12
AWG
10
AWG
8 AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1 AWG
25-30
14
AWG
10
AWG
10
AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
30-35
14
AWG
10
AWG
8 AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
35-40
12
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
40-45
12
AWG
10
AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
45-50
12
AWG
8 AWG
6 AWG
6 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
3/0
AWG
50-55
12
AWG
8 AWG
6 AWG
6 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
3/0
AWG
55-60
10
AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
1 AWG
0 AWG
0 AWG
3/0
AWG
4/0
AWG
60-65
10
AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
3/0
AWG
4/0
AWG
65-70
10
AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
3/0
AWG
4/0
AWG
70-75
10
AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
0 AWG
2/0
AWG
2/0
AWG
4/0
AWG
75-80
10
AWG
6 AWG
4 AWG
4 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
3/0
AWG
4/0
AWG
80-85
10
AWG
6 AWG
4 AWG
4 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
3/0
AWG
4/0
AWG
85-90
10
AWG
6 AWG
4 AWG
4 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
3/0
AWG
4/0
AWG
90-95
8 AWG
6 AWG
4 AWG
2 AWG
2 AWG
1 AWG
2/0
AWG
3/0
AWG
3/0
AWG
95-100
8 AWG
6 AWG
4 AWG
2 AWG
2 AWG
0 AWG
2/0
AWG
3/0
AWG
4/0
AWG
*One-way cable length from supply (usually battery) to load.

DISCOVER D3.
INSTALL & OPERATION MANUAL
17
7.4 CABLE GAUGE CHART 24V
Supply & Return Cable Conductor Size Chart 3% drop for when using 24V DC supply
Cable
length
(feet)*
Circuit Current
2 Amp
4 Amp
6 Amp
8 Amp
10 Amp
15 Amp
20 Amp
25 Amp
30 Amp
40 Amp
50 Amps
0-5
18
AWG
18
AWG
18
AWG
18
AWG
18
AWG
16
AWG
14
AWG
14
AWG
12
AWG
12
AWG
10
AWG
5-10
18
AWG
18
AWG
16
AWG
16
AWG
14
AWG
12
AWG
12
AWG
10
AWG
10
AWG
8 AWG
8 AWG
10-15
18
AWG
16
AWG
14
AWG
14
AWG
12
AWG
12
AWG
10
AWG
8 AWG
8 AWG
6 AWG
6 AWG
15-20
18
AWG
16
AWG
14
AWG
12
AWG
12
AWG
10
AWG
8 AWG
8 AWG
6 AWG
6 AWG
4 AWG
20-25
18
AWG
14
AWG
12
AWG
12
AWG
10
AWG
8 AWG
8 AWG
6 AWG
6 AWG
4 AWG
4 AWG
25-30
16
AWG
14
AWG
12
AWG
10
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
4 AWG
2 AWG
30-35
16
AWG
14
AWG
12
AWG
10
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
4 AWG
2 AWG
35-40
16
AWG
12
AWG
10
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
40-45
14
AWG
12
AWG
10
AWG
10
AWG
8 AWG
6 AWG
4 AWG
4 AWG
4 AWG
2 AWG
2 AWG
45-50
14
AWG
12
AWG
10
AWG
8 AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1 AWG
50-55
14
AWG
12
AWG
10
AWG
8 AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1 AWG
55-60
14
AWG
10
AWG
10
AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1
AWG
0 AWG
60-65
14
AWG
10
AWG
8 AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1
AWG
0 AWG
65-70
14
AWG
10
AWG
8 AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1
AWG
0 AWG
70-75
12
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
2 AWG
2 AWG
2 AWG
0 AWG
2/0
AWG
75-80
12
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
80-85
12
AWG
10
AWG
8 AWG
6 AWG
6 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
85-90
12
AWG
10
AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
90-95
12
AWG
8 AWG
8 AWG
6 AWG
4 AWG
4 AWG
2 AWG
1 AWG
1 AWG
2/0
AWG
2/0
AWG
95-100
12
AWG
8 AWG
6 AWG
6 AWG
4 AWG
2 AWG
2 AWG
1 AWG
0 AWG
2/0
AWG
3/0
AWG
*One-way cable length from supply (usually battery) to load.

DISCOVER D3.
INSTALL & OPERATION MANUAL
18

DISCOVER D3.
INSTALL & OPERATION MANUAL
19
8 Warranty
Please remove this page and keep for your files
For technical assistance:
Europe: [e-mail]
The Americas: [e-mail]
Warranty Serial Code(s):
2022 Ocean LED Marine LTD
All Rights Reserved
Specifications are subject to change without
notice.
Trademarks are the property of Ocean LED
Marine LTD
www.oceanled.com
Ocean LED Marine LTD
Ocean LED USA LLC
Unit 1 Jacknell Road
Dodwells Bridge Industrial Estate
Hinckley,
Leicestershire LE10 3BS
United Kingdom
778 South Military Trail
Deerfield Beach
Florida
FL 33442-3025
USA
Tel: [phone]
Fax: [phone]
[e-mail]
Tel: [phone]
Fax: [phone]
[e-mail]