Luxor LED-SUWL30-XX User manual

www.luxormarine-rv.ca • P.O. Box 20062 Pioneer Park, Kitchener, ON N2P 2B4 • Tel: [phone]
USER MANUAL - LUXOR MARINE & RV
Important: Read all instructions prior to installation.
LuxOr LED Underwater Light
LED-SUWL30-XX
Features
316L Marine Grade Stainless Steel Poly-Carbonate Lens
5 foot Power Wire (18AWG) Internal Driver
Over-Temp Protection Waterproof IP68
Specifications
30W LED Underwater Boat Light
Input Voltage 9 ~ 32 VDC
Current Draw 0.97 A @ 13.5VDC
Total Power Consumption 13 W @ 13.5VDC
Operating Temperature -22˚ F~122˚ F (-30˚ C~50˚ C)
Available Colors Blue, White
LED Lifetime 50,000 Hours
LED Brand CREE
Warranty 2 Years
Dimensions Length 4.84 in (12.3 cm)
Width 1.73 in (4.4 cm)
Thickness 0.49 in (1.25 cm)
Weight 0.99 lb (0.45 kg)
Parts Included
1 - Underwater Boat Light (LED-SUWL30-XX)
2 - M4 Machine screws 2 - M4 Flat washers
2 - M4 Locking Nuts 2 - M4 Self Tapping screws
2 - Neoprene washers
Recommended Tools (not included)
Drill and Drill Bits #2 Phillips Screwdriver
Heavy Grit Sandpaper Masking Tape
Isopropyl/Denatured Alcohol Lint Free Cloths
Marine Sealant Pencil (Wax Pencil
recommended for fiberglass)
Caution
Lights must be submerged to avoid overheating.
Use out of water will decrease led lifetime and cause early failure.
Lights have over temperature protection (for testing purposes only) and will
shut off when max temp (194˚ F / 90˚ C) is reached.
Do not operate lights out of water for more than 15 seconds for testing.
Lights will be hot if operated out of water for extended periods and will void
all warranties.
Installation of lights must be done while boat is out of water and dry.
LuxOr Marine & RV is not responsible for any injury or property damage
incurred due to improper installation.
Installation Instructions
IMPORTANT: Know your hull; most
common type is fiberglass. Wood, metal
and carbon fiber are other less common
hull types. For metal or carbon fiber
hull, first be sure to mount an insulating
material between metal or carbon fiber
surfaces and lights to prevent galvanic
corrosion. Underwater lights should not
come in contact with anti fouling paint
when installing or installed.
If the hull of your boat is metal or
carbon fiber surface,you can use the
plastic flat washers between hull and
back of light.
If uncertain about type of hull, please
contact boat manufacturer for assistance.
1. Determine desired mounting
location on boat’s transom.
Be sure to check actual draft water
level if operating LED lights at
speed. (See diagram below)
Recommended mounting depth
between 6-8” below waterline for
best effect. Be sure that mounting
location is free of any obstructions
before drilling through hole. Mark
center of desired location.
Water Line at IDLE
Water Line at SPEED
OVERHEAT

www.luxormarine-rv.ca • P.O. Box 20062 Pioneer Park, Kitchener, ON N2P 2B4 • Tel: [phone]
USER MANUAL - LUXOR MARINE & RV
LuxOr LED Underwater Light - LED-SUWL30-XX
2. Drill 1/4” through hole in center of
desired location and feed power
wire through hole into boat. Hold
light flush against transom, mark
location for mounting screws,
then remove light. Drill pilot holes
for mounting screws to prevent
cracking in fiberglass hulls.
3. Use heavy grit sandpaper to rough
up the surface and to remove any
debris from drilling. Clean area
using alcohol and lint free cloth.
4. Apply uniform layer of marine
sealant to back side of light,
especially around mounting holes
and wire connection. Also apply
marine sealant to transom surface
around pilot and through holes.
5. Feed power wire back through
1/4” hole into boat and press light
against transom using uniform
pressure. Install mounting screws
with included neoprene washers
and tighten light to transom.
6. Use sealant that has squeezed
out from beneath light to create
complete seal around outer edge of
light. Remove any excess sealant.
7. Connect positive wire to positive
battery terminal through fuse
to switch (see diagram below).
Connect negative wire to negative
battery terminal. Marine grade heat
shrink butt connectors and ring
terminals are recommended.
8. Ensure light is solidly attached to
hull and that marine sealant has fully
cured prior to putting boat in water.
Lights may be tested briefly while
out of water. Lights will overheat
and shut down if operated out of
water for more than testing.
Installation Instructions (continued)
Wiring Diagram
LED-SUWL30-XX Switch Fuse Connector Battery