AL Tech AE-L-WP-40 User manual

!
Contact Us:
7057 Marcelle St,
Paramount, CA 90723
800-640-0386
www.altechefficiency.com
[e-mail]
“The only wall pack in the industry with a patented tilt
board design allowing you to change the angle of the
projected light….” LED Magazine
LED Wall Pack

Specifications
Wattage:
40W
60W
90W
Model Number:
AE-L-WP-40
AE-L-WP-60
AE-L-WP-90
DLC #:
JR-QJ-16100-40
JR-QJ-16100-60
JR-QJ-16100-90
DLC Partner:
JOLIGHTING
UL & CUL Number
E468385 / Deploys 40W Driver DRM-0360090
Certifications:
Voltage:
120-277V
Power Factor:
0.98
Frequency:
50/60Hz
Lumens Efficiency:
100LM/W
Kelvin (CCT):
4000K/4500K/5000K
CRI:
82+
IP Rating:
IP65
Lens:
Glass
Materials:
Die Cast Aluminum
Finish:
Black (Default)
LM70 Life Time:
100,000
Dimming Availability:
NA. (Default)
Warranty:
5 Years
Temperature Range:
-34℃~ 54℃(-30℉~ 120℉)
Weight:
4.1KG
9.0LB
4.1KG
9.0LB
6.6KG
15.0LB
Packaging Dimensions:
395*280*245MM
15.6*11.0*9.6INCH
395*280*245MM
15.6*11.0*9.6INCH
475*275*285MM
18.7*10.8*11.2INCH
Replacement Wattage:
150W
250W
350W


Dimensions$
40W/60W
90W

User Guide
Note:
Please read this entire manual to fully understand and safely use the luminaire. The
products can be used at the voltage of 100-277V AC, 50/60HZ, suitable for indoor and
outdoor, moisture proof and dust proof. Specifications are subject to change without
notice. Please visit www.altechefficiency.com for the most recent product information.
Unpacking:
1. Unpack and carefully examine the product.
2. Report any damage and save all packing materials if any part(s) were damaged during shipping.
3. Do not attempt to use the fixture if it is damaged.
Before You install:
1. Before installing any light fixtures, read and understand all cautions, warnings, instructions and product
labels. Failure to do so can result in injury and/or void the warranty.
2. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
3. The product should be installed and operated by a qualified electrician or technician in accordance
with relevant local codes.
4. Risk of electric shock. Ensure that main power source is off when wiring or soldering the sections of
the product.
Maintenance:
1. Disconnect the product from the power supply prior to cleaning.
2. Use a dry or slightly moistened cloth for cleaning.
3. Never use any chemicals or abrasive materials for cleaning.
Installation Instructions:
1. Loosen the screws on the side of the wall pack and open the fixture.
2. Loosen the secure screw on the right side of the light board.
3. Swivel open the light board to expose the back of the fixture.
4. Connect the input and ground wires of the fixture to the power supply. White is live. Black is neutral.
Green is ground.
5. Secure the fixture to the mounting box with screws.
6. Connect the LED array to the output leads of driver.
7. Close the light board and replace the secure screw.
8. Close the fixture, replace and tighten the two housing screws.
9. This fixture is designed for years with minimum care. For optimum performance, periodically clean the
lens with a mild, non abrasive glass cleaner and soft cloth. DO NOT use solvents or cleaners
containing abrasive agents. When cleaning the fixture, make sure you have the power turned off and
do not spray liquid cleaner directly onto the LED, socket or wiring.