alatech OB001 User manual

Please charge the sensor for the first use and when the battery is low (Green
flashing LED). Please make sure the charging station and charge terminals at
sensor back are clean and dry before charging to prevent any poor connection.
Put the sensor back facing down to align the charge contacts with the charge
terminals; refer to Fig. A.
Lock the sensor on the side close to the USB cable on charging station and
then lock on the other side; refer to Fig. B.
Connect the USB to a wall charger or your computer.
The green indicator will continuously flash when charging. The light will be
constantly ON when the charge is completed.
Take out the sensor from the charging station by sliding up or down; refer to
Fig. C.
OB001 OPTICAL
HEART RATE ARMBAND
Quick Start Guide
FEATURES
IN THE BOX
HOW TO CHARGE
1
2
3
4
5
Dual mode technology
Compatible with sport watch /Cycling computer /fitness equipment and smart
device with Bluetooth 4.0, ANT+; also work with most Bluetooth Smart Fitness
Apps.
Storage function
The built-in memory can independently record and store heart rate data and
SPM(Steps per minutes); no need to bring the smartphone or wear the watch
when exercising. After exercising, the user can synchronize the data to Ala
Connect through Bluetooth to review the training overview.
Lightweight and comfortable
The sensor and armband are less than 20 grams; can be worn on the forearm or
upper arm.
1
2
3
Sensor
Armband
USB charging station
4
5Quick guide
Warranty card
3
2
1
LED indicators
Button
Charge terminals
Lock on
Lock on first
Charging
contacts
Charging
terminals
LED
Indicators
ABC
Scan QR Code or search for Ala Connect on
Apple Store or Google Play and download.
Long press the sensor to activate (long
press until the red indicator is ON).
Open Ala Connect and add device
according the instructions. User’s age will
be written into the sensor automatically
after the device is successfully added.
Wear the sensor and go out for exercise.
After the exercise, open Bluetooth and Ala
Connect on your mobile device to
synchronize your training data wirelessly.
The uploaded training data will be stored in
the cloud. Log in cloud.alatech.com.tw to
check your activity report and results.
APP USE AND SENSOR PAIRING
1
2
3
4
5
6
System requirements of APP
installation:
• Support iOS 9 or above
• Support Android 4.4 or above
• Built-in BluetoothTM 4.0 or above
* Also compatible with other apps,
such as Strava and Wahoo fitness.
Velcro
Fuzzy side facing the outside
To ensure accurate cadence
detection, wear the sensor on
the inside of the forearm.
Slide both ends of the armband through the
buckles at both ends of the sensor.
Wear the sensor on the inside of forearm or
upper arm. Please do not wear on the wrist
and avoid any tattoo and hair.
Adjust the tightness to make sure the sensor
fits the arm.
HOW TO WEAR
1
2
3

SPECIFICATIONS
2PF290082080002
2019/01 V0
FCC
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following
two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the Federal Communications Commission
(FCC) rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment causes harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by doing one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user‘s authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions for
satisfying RF exposure compliance. The antenna(s) used for this transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
•To ensure accurate readings, clean the sensor lens with a soft and dry cloth.
•It is recommended to wash the armband with warm water (under 40°C). DO
NOT use the brightener, soap or softener. DO NOT soak, iron, dry clean, bleach
and twist.
HOW TO CLEAN
The sensor only comes with one button; the operation of different uses is
described as follows:
BLUETOOTH AND LED INDICATORS
Heart Rate Zone*
Z1 Warm Up
Increase speed and lactate threshold;
Only suitable for short-distance pace,
cannot maintain for a long time
Z2
Z3
Z4
Z5
Easy
Aerobic
Threshold
Maximum
Training intensity
% (%MHR)
~60%
75%~
60-75%
LED Flash
frequency
Low speed
Intermediate
speed
High speed
Training functions
Facilitate warm-up and energy
recovery
Improve metabolism
Enhance aerobic fitness
Notes
When the sensor is recording or connecting to Bluetooth, low battery light will not be ON.
The user can upload the recorded data to Ala Connect through Bluetooth communication.
When LED is constant ON, the sensor will turn off automatically if there is no operation or
connection over 3 minutes.
Blue /Red LED flash frequency varies according to user’s heartbeat in the heart rate zone at
that time:
* The sensor will define your heart rate zone according to the age and maximum heart rate
(%MHR) input in Ala Connect
Charge
Charging
Fully charged
Activate
Power on
Standby
Low battery Note 1
When used as an independent training device
Start recording
Stop recording
Bluetooth connection
Pairing
Synchronizing data Note 2
When used as an accessory for heart rate monitor and paired with compatible devices
Heart rate detected
Heart rate not detected
Green
Flash
Constant ON Note 3
Flash
Blue
Constant ON Note 3
Flash
Constant ON Note 3
Flash Note 4
Red
light up
Constant ON Note 3
Blinking Note 4
Constant ON Note 3
Button
operation
Long press
Short press
Short press
!
1
2
3
4
• Model: OB001
• Dimension: L 48×W 31.5×D 12.5mm
• Armband: L 380×W 25mm
• Weight: 13g (armband excluded)
• Memory capacity: Up to 30 hours training
• Operating temperature: -10~60°C (-14~140°F)
• Charge temperature: 10~45°C (50~113°F)
• Wireless transmission interface: Bluetooth 4.0/ANT+
• Wireless transmission frequency: 2.402~2.480 GHz
• Battery: rechargeable lithium battery
• Input voltage: 5V
• Run time: 40 consecutive hours (max.)