Albasca MK-2800BT User manual
- 1 -
Bluetooth Linear Imager Scanner
Configuration Guide
MK-2800BT
- 2 -
- 3 -
Table of
Contents
Chapter 1 System Information
1.1 About this manual 4
1.2 Pairing Cradle --------------------------------------------------------------------- 5
1.3 Pairing Smart Phone, Tablet PC ---------------------------------------------- 6
1.4 Sleeping time setting ----------------------------------------------------------- 7
1.5 USB Country Keyboard Types ------------------------------------------------- 8
1.6 How to set up the parameter 9
Chapter 2 System Setup
2.1 Terminator 10
2.2 String Options (Prefix & Suffix) 11
2.3 Setup Insertion 12
Chapter 3 BarCode
parameters
setting
3.1 UPC-A 16
3.2 UPC-E 19
3.3 EAN-13 22
3.4 EAN-8 24
3.5 Code39 26
3.6 Codabar 29
3.7 Code93 33
3.8 Code128 35
3.9 Interleaved2 of 5 38
3.10 Industrial 2of 5 40
3.11 Matrix 2 of 5 42
3.12 China Postage 44
3.13 MSI/Plessey 46
3.14 Code 32 4 8
3.15 Code 11 50
3.16 Telepen 52
3.17 GS1 DataBar 54
Appendix 56
- 4 -
Chapter 1 - System Information
1.1 About this manual
This User's Guide provides detailed
programming instructions.
Barcode
scanners are factory
programmed
for the most common communication
setting. If you need to change these settings, programming is accomplished
by scanning the bar codes in this guide.
1.2 How to set up the
parameter
-I
(1) Scan Start Configuration
(2) Scan all
necessary
labels for
parameters
that meet your applications.
(3) Scan End
Configuration
to end the programming.
Start configuration End configuration
Default
setting
Check
Version
An asterisk (*) next to an option indicate the default setting.
- 5 -
1.2 Pairing Cradle
1. Scan "setting configuration"
2. Scan "open SPP "
3. Scan "disconnect previous pairing"
4. Scan "Cradle bottom BT address barcode"
5. Scan "Repairing"
6. Scan "Save BT SPP setting"
7. Scan " End BT SPP setting "
Apple device needs enable transmission, others need to disable
Enable iOS transmission
Disable iOS transmission
- 6 -
1.3 Pairing Smart Phone ,Table PC
1. Scan "setting configuration”
2. Scan " Open HID connection "
3. Scan " Disconnection previous pairing "
4. Scan " BT visible setting "
5. Scan " Save BT HID configuration "
6. Scan " End BT HID configuration "
Apple device needs enable transmission, others need to disable
Enable iOS transmission Disable iOS transmission
Enable BT function in iPad or smart phone and then serach BT
(NVC_MD_CS45) to pair.
- 7 -
1.4 Sleeping time and Buzzer setting
5 min
10 min
30 min
Always ON
High
Low
Off
Buzzer
- 8 -
1.5 USB Country Keyboard Types
Keyboard layouts vary from country to country. The default setting is 1-U.S.
keyboard.
USA Germany
Italy France
Spain Japan
Czech Denmark
Belgium Finland
Dutch Hungary
Finlan
d
- 9 -
1.6 How to set up the parameter - II
Most of time the scanner only requests one read of
parameters
when
changing to new values. You will hear two beeps when you successfully
set to the new values. But for some special
parameters,
multiple reads are
needed to
complete
the configuration. When use these special parameters.
In some cases, you might need to read one or more barcodes, such as:
Hexadecimal barcodes. For example: prefix, suffix, etc.
Numeric barcodes. For example: inter-character delay, max/min length
To complete the change of setting you will need to read the “Confirm”
barcode after you read the parameter. Below is the flow chart to explain
two different configurations.
- 10 -
Chapter 2 - System setup
Start configuration End configuration
2.1 Terminator
ITEM OPTION
None
*CR+LF
Output Characters
CR
LF
Tab
- 11 -
2.2 String Options (Prefix & Suffix)
This section describes the alterations which can be made to the format of
the transmitted data string. A prefix and suffix of maximum 20 direct
input may be
included
in front and at the end of scanned barcode.
Format
{Prefix} {Code ID} {Bar Code} {Suffix}
How to set up a prefix?
To
configure
“## “as prefix
(1) Scan Start
Configuration
barcode
(2) Scan Preamble bar code
(3) Scan ‘#”twice from FULL ASCII table
(4) Scan Confirm
configuration
barcode
(5) Scan End
Configuration
barcode.
How to set up a suffix?
To
configure
“$$”as suffix
(1) Start
configuration
barcode
(2) Scan Postamble barcode
(3) Scan ‘$”twice from FULL ASCII table
(4) Scan Confirm
configuration
barcode
(5) Scan End
configuration
barcode.
- 12 -
2.3 Setup Insertion
This section describes how to setup the insertion of output.
NOTE :
Max. 10 charters can be inserted each time
Max.
Insertion
group is only two.
Insertion group (01) or (02) can be used in different kinds of
barcodes at the same time
- 13 -
Example:
:
To insert character “A”before the third digit(3)
Make the decoded data: 12A3456789
How to set up a character you want to insert
(1) Scan Start
Configuration
barcode
(2) Scan “G1 Insertion character”
(3) Scan “4”and “1”from FULL ASCII Table
(4) Scan Confirm
configuration
barcode
(5) Scan End
configuration
barcode
How to set up position you wish to place the character
(6) Scan Start
Configuration
barcode
(7) Scan “G1 Character Position”
(8) Scan “0”and “3”from FULL ASCII Table (which presents the position)
(9) Scan Confirm
configuration
barcode
(10) Scan End
configuration
barcode
How to set up insertion for code 39
Go to chapter 3.5 (code 39)
(11) Scan Start
Configuration
barcode
(12) Scan “Insert group selection”bar code
(13) scan “0”and “1”from FULL ASCII Table
(which presents the group- 01 you just set up previously)
(14) Scan Confirm
configuration
bar code
(15) Scan End
configuration
barcode
- 14 -
Start configuration End configuration
Confirm configuration
ITEM OPTION
Preamble
(Default
：
00)
Postamble
(Default
：
00)
G1 Insertion
character
(Default
：
00)
G2 Insertion
character
(Default
：
00)
G1 Character Position to
be
inserted (Default
：
00)
G2 Character Position to
be
inserted (Default
：
00)
Ref: Appendix
Ref: Appendix
Ref: Appendix
Ref: Appendix
Ref: Appendix
Ref: Appendix
- 15 -
Start configuration End configuration
ITEM OPTION
Bar Code
ID
Accuracy
Positive and negative bar
codes
*Disable
Enable
* Read 1
Time Read
2
T
imes
Negative
bar
codes
*Positive bar
codes
Code Type ID Code Type ID
UPC-A FInterleaved 25 N
UPC-E GIndustrial 25 O
EAN-13 HMatrix 25 P
EAN-8 IChina Postal Code Q
Code 39 JMSI/Plessey R
Codabar KCode 32 S
Code 93 LCode 11 T
Code 128MTelepen V
- 16 -
Chapter 3 - Bar Code parameters setting
How to set up a Code ID?
(1) Scan Start
configuration
bar code
(2) Go to the ASCII Table and scan label that represent the desired
characters to be inserted.
(3) Scan Confirm
configuration
bar code
(4) Scan End
configuration
bar code.
Start configuration End configuration
Confirm configuration
3.1 UPC-A
ITEM OPTION
Read
Code ID
Setting
(Default : F
)
Disable
*
Enable
Ref: Appendix
(20-7EH)
- 17 -
Start configuration End configuration
ITEM OPTION
UPC-A Expand to
EAN-13
Check Digit
Send
Truncate
Leading
Zero
Truncate
Leading
(Default:00)
Truncate
Ending
(Default:00) Insert
group
selection
*
Disable
Enable
Disable
*
Enable
*
Disable
Enable
Ref: Appendix
(00-0DH)
Ref: Appendix
(00-0DH)
Ref:
Appendix
（
00—02H
）
- 18 -
Start configuration End configuration
ITEM
OPTION
*
NONE
2
digits
Supplement digits
5
digits
2 or
5digits
Auto-discriminate Supplement
- 19 -
3.2 UPC-E
Start configuration End configuration
ITEM OPTION
Read
Disable
* Enable
Code ID setting
(Default : G) Ref: Appendix (20-7EH)
- 20 -
Start configuration End configuration
ITEM OPTION
UPC-E Expand to
UPC-A
Check Digit
Send
Truncate
Leading
(Default:00)
Truncate
Ending
(Default:00)
Insert group
selection
(Default:00)
* Disable
Enable
Disable
* Enable
Ref: Appendix (00-08H)
Ref: Appendix (00-08H)
Ref: Appendix (00-02H)
Table of contents
