Scandex SX-1124 User manual

USER GUIDE V2
SX-1124 WIFI LASER SCANNER

INDEX
Characteristics...............................................................
Settings.........................................................................
Functions.......................................................................
Working Modes...............................................................
Character Codes Table....................................................
Performance Parameters.................................................
Operation Guide.............................................................
Number of Conceal Characters Table................................
Maintenance Record.......................................................
Prefix & Suffix.................................................................
Warranty........................................................................
Content..........................................................................
1
3
2
5
11
14
17
19
22
23
24
9

1
Please take time to read this user guide before using the barcode scanner.
If you have any questions please contact us or alternatively support is available
via the “Scandex Red Card”enclosed in the box.
CHARACTERISTICS
Ergonomic design. External soft rubber bumpers and rugged internal build
for better and faster barcode reads. Easy to use with a simple setup. Large capacity,
superior to the average drop resistance. The latest barcode engine and decoding technology
Scanning setting alarm: A short beep. Low voltage alarm: A long beep.
greater than ordinary scanners ensures longer use after fully charged.
Pairing operation failure: 6 short beeps.
Data uploading success: 2 short beeps. Failure: 3 short beeps
SOUND GUIDE

2
FUNCTIONS
Automatic jumping frequency. Strong Anti-Interference ability.
Transmission distance with obstacles under ‘Normal Mode’
is 20m-100m and over 400m with no obstacles.
If the distance is exceeded 3 beeps will sound, indicating the data load has failed.
Each scanner has a unique mechanical ID to avoid interferences with other devices in use.
The customizable ID allows the user to distinguish the data source easily.
The pairing method is very simple. Repeated pairing is possible.
The ‘Check Mode’ is simple and easy to use.
Can storage between 5000-10000 barcode messages.
Automatic ‘Sleep Mode’. Sleeping current is less than 10UA,
this extends greatly the standby time of the battery.
A special charging circuit guarantees a safe charge.

3
0 1 2 3
4 5
Wi-Fi channel settings (2 digit) Scanner ID settings (2 digit)
‘Wi-Fi CHANNEL’ & ‘SCANNER ID’ SETTINGS
PARAMETERS TABLE
6 7
98

4
Hide scanner IDDisplay scanner ID
Settings
8 hours
20s
2min
30s 60s
5min 10min 20min
‘SCANNER ID’: DISPLAY / HIDE
‘SLEEP MODE’ SETTINGS
No sleeping

5
Recovery Routine Wireless Mode
Note: Do not read ‘Recovery Routine’ under ‘Common Mode’.
Upload Data Total Quantity Data Clear Data
Normal Mode Non-Losing Mode Checking Mode
WORKING MODES
WORK STATUS

6
Close the Attached
Code of UPC & EAN
Add 2 Bits Attached
Code to UPC & EAN
Add 5 Bits Attached
Code to UPC & EAN
Add 2 and 5 Bits Attached
Code to UPC & EAN
Enable Enter Disable Enter
Line Skip
‘UPC / EAN ATTACHED CODE’ SETTINGS
‘ENTER’ & ‘LINE SKIP’ SETTINGS

7
OTHER BARCODE SETTINGS
Note: ASCII setting is used for Code39 incomplete characters.
Open Code39 Transmit
Open FULL ASCII
Open Code32 Close Code32 Open China postal code
Close China postal code
Close FULL ASCII
Close Code39 Transmit
Start / Stop Character Start / Stop Character
Open CODABAR Transmit Close CODABAR Transmit
Start / Stop Character Start / Stop Character

8
English Italian French
0.1 s
0.5 s 1 s 2 s
9600 19200 38400 115200
German
Turkish Czech Finnish Spanish
LANGUAGE SETTINGS
SERIAL PORT ‘BAUD RATE’ SETTINGS
CHECKED DATA ‘UPLOAD SPEED’ SETTINGS

Add Prefix
Add Suffix
9
ADD PREFIX
ADD SUFFIX
Example: To add the prefix ‘AM’ scan the following codes: ‘Add Prefix’.
Turn to page 11,from the ‘Character Codes Table’ scan the codes ‘A' and ‘M’.
Maximum 32 characters.
Example: To add the prefix ‘AM’ scan the following codes: ‘Add Suffix’.
Turn to page 11,from the ‘Character Codes Table’ scan the codes ‘P' and ‘M’.
Maximum 32 characters.

Conceal Initial Characters
Conceal Final Characters
10
CONCEAL INITIAL CHARACTERS
CONCEAL FINAL CHARACTERS
Example: To conceal the two first characters of the barcodes we read,
Example: To conceal the four last characters of the barcodes we read,
scan the following codes: ‘Conceal Initial Characters’.
scan the following codes: ‘Conceal Final Characters’.
Turn to page 14, from the ‘Number of Concealed Character Table’ scan the code ‘02'.
Turn to page 14, from the ‘Number of Concealed Character Table’ scan the code ‘04'.

01 2 34
56 7 8 9
A B C D E
F G H I J
K L M N O
11
CHARACTER CODE TABLE

PQR S T
UV W X Y
Z&,( )
*+!,:
;‘-< >
12

{}
=/“#
?@$%
[ ] \^
_`
13
|~

01
05
09
13
02
06
10
14
03
07
11
15
04
08
12
16
14
NUMBER OF CONCEALED CHARACTERS TABLE

17
21
25
29
18
22
26
30
19
23
27
31
20
24
28
32
15

F1 F2 F3 F4
F5 F6
F7 F8 F9 F10 F11 F12
16
BS/Back Space
Page Up
Scroll Lock
Page Down
Inert
UP
Delete
Down
Home
Left
End
Right
Num Lock Caps Lock Enter Space TAB
KEY FUNCTION SETTING

Turn on the scanner and read the code ‘Wi-Fi channel settings’ on page 3.
Connect the receiver to the computer’s USB interface, the receiver will display a blue light.
From the ‘Parameters Table’ on page 3, scan the codes needed.(i.e. Read ‘0' and ‘1' if channel is ‘1').
Adjustments should be made before the blue light goes out, approximately 10 seconds.
If you run out of time, you should remove the receiver and start again.
Read the code ‘Scanner ID settings’, on page 3.
From the table ‘Parameters Table’ on page 3, scan the codes needed. (i.e.Read ‘0' and ‘1' if ID is ‘1').
When the scanner reaches the pre set sleeping time, 20s when manufactured, it will switch off automatically.
The scanner can be turned off also by pressing and hold the trigger for 2 seconds.
17
OPERATION GUIDE
MATCHING SETTING
ID SETTING
SWITCHING OFF

The red light indicates the scanner is charging.
Please use the charging equipment supplied to charge the scanner.
When the red light is off indicates the scanner is fully charged.
Note: Under ‘No Losing Mode’, when the signal exceeds the transmission distance
and the receiving terminal cannot receive signals,
the read barcode data will be stored automatically, this guarantees no data lost.
as long as the scanner reads the code ‘Data Upload’.
This stored data will be loaded in the computer automatically
(We suggest that ‘Clear Data’ shall be read at first under this mode,
enabling the data to be seen clearly when ‘Data Upload’ is performed after barcodes are read).
improving greatly the work efficiency of the user.
Under this mode, work will not be affected by the transmission distance
CHARGING
18