Alcatel-Lucent OmniAccess 6000 User manual

i
OmniAccess 6000
Wireless LAN Switch
Installation Guide
TM

OmniAccess 6000: Installation Guide
ii Part 031639-00 May 2005
Copyright
Copyright © 2005 Alcatel Internetworking, Inc. All rights reserved.
Specifications in this manual are subject to change without notice.
Originated in the USA.
Trademarks
Alcatel AP60/61, Alcatel 70, Alcatel 6000, and Alcatel AOS-W, are trademarks
of Alcatel in the United States and certain other countries.
Any other trademarks appearing in this manual are owned by their respective
companies.

iii
Electromagnetic Interference
FCC - Class A
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at their own expense.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This product complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Industry Canada - Class A
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus as set out in the interference-causing
equipment standard entitled “Digital Apparatus,” ICES-003 of the Department
of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques
applicables aux appareils numériques de Classe A prescrites dans la norme
sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le
ministère des Communications.
VCCI - Class A
CE - Class A

OmniAccess 6000: Installation Guide
iv Part 031639-00 May 2005
Warning—This is a Class A product. In a domestic environment, this product
may cause radio interference in which case the user may be required to take
adequate measures.
EU - Class A
This product complies with EN55022 Class A and EN55024 standards.
Safety
Lithium Battery Notice
The Alcatel 6000 Supervisor Card used with this product contains a lithium
battery.
Laser Notice
The Alcatel 6000 Line Cards used with this product use replaceable laser
transceiver modules on some ports.
This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and
IEC 60825-1: 1993, A1: 1997, A2: 2001, IEC 60825-2: 2000.
For continued compliance with the above laser safety standards, only
approved Class 1 modules from our approved vendors should be installed in
the product. See “Gigabit Ethernet Ports” on page 52 for a list of approved
modules and vendors.
CAUTION—The lithium battery may explode if it is incorrectly replaced. Replace
only with the same or equivalent type battery recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
CAUTION—Use of controls or adjustments of performance or procedures other
than those specified in this manual may result in hazardous radiation exposure.
CLASS 1
LASER PRODUCT

Contents v
Contents
To the Network Manager vii
The Alcatel Wireless LAN
Solution . . . . . . . . . . . . . . . . vii
Deployment Summary . . . . . . . viii
Preface xi
Overview of this Manual. . . . . . . xi
Related Documents . . . . . . . . . . xi
Text Conventions. . . . . . . . . . . . xii
Contacting Alcatel . . . . . . . . . . xiii
Chapter 1 System Overview . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . 1
Physical Description. . . . . . . . . . 2
Chapter 2 Installing the Chassis . . . . . . . 5
Pre-Installation Checklist . . . . . . 5
Precautions . . . . . . . . . . . . . . . . 6
Requirements . . . . . . . . . . . . . . 7
Mounting the Chassis . . . . . . . . 9
Adding Modules . . . . . . . . . . . 11
Connecting Power . . . . . . . . . . 11
Chapter 3 Verifying the Installation . . . 15
Chapter 4 The Fan Tray. . . . . . . . . . . . . 17
Features . . . . . . . . . . . . . . . 17
Physical Description. . . . . . . . . 18
Replacing a Fan Tray . . . . . . . . 19

OmniAccess 6000: Installation Guide
vi Part 031639-00 May 2005
Chapter 5 The Power Supply . . . . . . . . . 23
Features . . . . . . . . . . . . . . . . 23
Physical Description . . . . . . . . . 25
Power Management . . . . . . . . . 27
Power Requirements
Worksheet . . . . . . . . . . . . 27
Required Power Supplies . . . . 29
Maximum Power Load . . . . . . 29
Inserting a Power Supply . . . . . . 30
Removing a Power Supply . . . . . 33
Chapter 6 The Supervisor Card . . . . . . . 35
The Alcatel OmniAccess
Supervisor Card I. . . . . . . . . . 35
Features . . . . . . . . . . . . . . . . 35
Physical Description . . . . . . . 36
Port & Cable Specifications . . 39
Inserting a Supervisor Card . . . . 41
Removing a Supervisor Card . . . 43
The Alcatel OmniAccess
Supervisor Card II . . . . . . . . . 44
Chapter 7 The Line Cards . . . . . . . . . . . . 45
OAW-LC-2G24F Features . . . . . . 45
Physical Description . . . . . . . 46
Port & Cable Specifications . . 49
OAW-LC-2G Features . . . . . . . . 54
Physical Description . . . . . . . . . 55
Inserting a Line Card . . . . . . . . . 57
Removing a Line Card . . . . . . . . 59
Appendix A Specifications . . . . . . . . . . . . 61

To the Network Manager vii
To the Network
Manager
As with any full-featured network equipment, deploying the
Alcatel Wireless LAN solution requires a degree of planning. The
process may involve multiple components as well as various
individuals in your organization. As the network manager, you
should become familiar with the components and deployment
summary outlined in this section.
The Alcatel Wireless LAN Solution
The Alcatel Wireless LAN solution consists of three major
components:
zAlcatel Wireless LAN Switch. This is an enterprise-class
switch into which multiple Access Points (APs) and Air Moni-
tors (AMs) are connected and controlled.
zAlcatel Wireless Access Point. This is a next-generation wire-
less transceiver which functions as an AP or AM. Although
third-party APs can be used with the Alcatel Wireless LAN
system, the Alcatel AP provides the best features and easiest
integration.
zAlcatel AOS-W Switch Software. This software intelligently
integrates the Wireless LAN switch and APs to provide load
balancing, rate limiting, self healing, authentication, mobility,
security, firewalls, encryption, and centralization for monitor-
ing and upgrades.

OmniAccess 6000: Installation Guide
viii Part 031639-00 May 2005
Deployment Summary
This section outlines the various tasks involved in deploying the Alcatel
Wireless LAN solution, and indicates the document where appropriate
instructions can be found.
NOTE—Documents named below are included on the Alcatel Documentation Library CD-ROM.
Physical installation of the Alcatel Wireless LAN Switch
Installation requires a trained technician, experienced with handling and
installing similar equipment. This phase involves the following tasks:
zTransport, unpack, and mount the switch in a suitable rack environment.
zIf using a modular switch chassis, install any extra modules you may have
ordered.
zAttach power and a console.
zBoot the system and perform the initial power-on test, examining the LEDs
and console messages to ensure proper operation.
The Alcatel Wireless LAN Switch Installation Guides provide the necessary
instructions.
Initial configuration of the Alcatel Wireless LAN Switch
Configuration requires someone who understands the company's wired
network and has experience with the physical and logical management and
configuration of routers, switches, servers, and clients. This phase involves the
following tasks:
zUse the console to perform initial configuration of the Alcatel Wireless LAN
Switch.
zAttach the switch to the network.
The Alcatel AOS-W Quick Start Guide and the Alcatel AOS-W User Guide
provides instructions.
Planning the location of access points and air monitors
This phase requires someone familiar with your wireless network deployment
strategy and the features required of the Alcatel Wireless LAN solution. You
can manually determine the locations for APs, or use a Web browser to access
the Alcatel Wireless LAN Switch’s built-in RF Plan tool and perform the
following tasks:
zDefine the physical site parameters.
1
2
3

To the Network Manager ix
zDetermine how many access points are needed and where they should be
located.
zSimulate network failures and recovery characteristics, and adjust place-
ment if necessary.
The Alcatel AOS-W User Guide provides instructions.
Physical installation of the Alcatel Wireless Access Points
This requires a trained technician. The following tasks are involved:
zPerform initial configuration of the AP.
zMount the AP in its appointed service location.
zAttach required network cables and power.
The Alcatel AP Installation Guides provide instructions.
Advanced configuration of the Alcatel Wireless LAN Switch
Again, configuration requires someone who understands the company's
network and has experience managing routers, switches, servers, and clients.
The following tasks are involved:
zConfigure the planned network features via command line or Web inter-
face.
zTest and debug the deployment.
The Alcatel AOS-W Reference Guide provides in-depth information and
examples on the Alcatel Wireless LAN Switch’s more advanced features.
Monitoring and maintenance
This requires someone experienced using various types of software tools to
gather and interpret network performance information. The following tasks
are involved:
zPerform remote monitor and management functions via command line or
Web interface.
zIdentify problems and initiate support when necessary.
zEnsure that hardware support issues are handled by a trained technician.
The Alcatel AOS-W Reference Guide provides instructions for collecting
system health and performance information. The Alcatel Wireless LAN Switch
Installation Guides and Alcatel AP Installation Guides provide instructions for
hardware issues.
4
5
6

OmniAccess 6000: Installation Guide
xPart 031639-00 May 2005

Preface xi
Preface
The preface includes the following information:
zAn overview of the sections in this manual
zA list of related documentation for further reading
zA key to the various text conventions used throughout this
manual
zAlcatel support and service information
Overview of this Manual
This manual is for trained technicians responsible for installing
the Alcatel 6000 series Wireless LAN Switch. The manual is
organized as follows:
zPart 1: The Alcatel 6000-series Chassis
The chapters in this section explain describe the Alcatel
6000-series Wireless LAN Switch system, and provide
instructions for mounting the chassis, attaching power, and
performing initial power-on tests.
zPart 2: The Alcatel 6000-series Modules
Each chapter in this section focuses on a specific module and
includes instructions for installing or replacing the individual item.
zPart 3: Appendices
Related Documents
The following items are part of the complete documentation for
the Alcatel system:
zAlcatel Wireless LAN Switch Installation Guide (this manual)
zAlcatel AOS-W User’s Guide

OmniAccess 6000: Installation Guide
xii Part 031639-00 May 2005
zAlcatel AP Installation Guide
Text Conventions
The following conventions are used throughout this manual to emphasize
important concepts:
TABLE P-1 Text Conventions
Type Style Description
Italics This style is used to emphasize important terms and to
mark the titles of books.
System items This fixed-width font depicts the following:
zSample screen output
zSystem prompts
zFilenames, software devices, and certain commands
when mentioned in the text
Commands In the command examples, this bold font depicts text
that the user must type exactly as shown.
<Arguments> In the command examples, italicized text within angle
brackets represents items that the user should replace
with information appropriate to their specific situation.
For example:
# send <text message>
In this example, the user would type “send” at the
system prompt exactly as shown, followed by the text of
the message they wish to send. Do not type the angle
brackets.
[ Optional ] In the command examples, items enclosed in brackets
are optional. Do not type the brackets.
{ Item A | Item B } In the command examples, items within curled braces
and separated by a vertical bar represent the available
choices. Enter only one choice. Do not type the braces or
bars.

Preface xiii
Contacting Alcatel
Web Site
E-mail
Telephone Numbers
zMain Site http://www.Alcatel networks.com
zSupport http://www.Alcatel networks.com/support
zSales sales@Alcatel networks.com
zSupport support@Alcatel networks.com
zMain 408-227-4500
zFax 408-227-4550
zSales 408-754-1201
zSupport In the U.S.: 800-WI-FI-LAN (800-943-4526)
International:408-754-1200

OmniAccess 6000: Installation Guide
xiv Part 031639-00 May 2005

System Overview 1
CHAPTER 1
System Overview
The Alcatel 6000-series Wireless LAN Switch is an
enterprise-class, modular switch which connects, controls, and
intelligently integrates wireless Access Points (APs) and Air
Monitors (AMs) into the wired LAN.
This chapter introduces you to the Alcatel Wireless LAN Switch. It
describes the general features of the modular system and
illustrates key physical elements. Once familiar with the system,
you can begin the installation process covered in the next chapter.
Features
This section outlines the general features of the Alcatel Wireless
LAN Switch.
z10/100/1000 Mbps Ethernet switch with high-speed
Layer-2/Layer-3 packet forwarding.
zHigh-performance packet processing provides value-added
wireless services such as load balancing, rate limiting,
self-healing, calibration, authentication, mobility, security, and
centralized monitoring and configuration.
z3U chassis can be mounted in a standard 19-inch network
equipment rack.
zModular, slot-based chassis allows for network expansion
and fault-tolerance.
zUp to 2 supervisor cards
zUp to 3 line cards for up to 72 10/100 Mbps Ethernet ports
and 6 Gigabit Ethernet ports
zUp to 3 power supplies with load sharing capability
zA fan tray containing three individual fans for redundancy

OmniAccess 6000: Installation Guide
2Part 031639-00 May 2005
zAll modules are hot-swappable by trained technicians.
Physical Description
FIGURE 1-1 Alcatel 6000-series Wireless LAN Switch
System
NOTE—Figure 1-1 depicts an Alcatel Wireless LAN Switch with the minimum
components required for operation. Depending on the options selected when
your system was purchased, your actual chassis may include more or fewer
of the pictured items. Cover unused slots with blank plates.
Slot 0
This slot is for the required supervisor card. The supervisor card processes all
traffic from the line cards and performs all management functions.
Slot 1
This is a dual-purpose slot. It can be used for a second, optional supervisor
card to provide redundancy for extra processing capacity or fault tolerance.
Alternately, this slot can be used for a third line card to provide extra network
port capacity.
Slot 2
This slot is for the required line card. The line card provides network ports for
connecting wireless APs, such as the Alcatel Wireless Access Point, as well as
wired LAN segments.
5 6 7 5
0 1 2 3
Mount
Holes
Mount
Holes
Fan Tray
Slot
Module
Handles
Power Supply Slots
Card Slots
4
0
1
2

System Overview 3
Chapter 1
Slot 3
This slot is for adding a second line card.
Module Handles
All module handles are used only for removing and inserting the individual
modules.
Holes for attaching rack mounting brackets (on side)
Fan Tray Slot
The Alcatel Wireless LAN Switch is cooled by a hot-swappable fan tray. The
fan tray pulls air from right to left (as viewed from the front of the chassis)
across the installed cards.
During operation, the air vents on the left and right sides of the chassis must
remain unobstructed by cables or mounting equipment. For proper air
circulation, leave at least 10 cm (4 inches) of clearance on the left and right of
the chassis.
Power Supply Slots
The chassis has slots for up to three power supplies. The number and type of
power supplies required for your system depends on the number and type of
line cards installed, and whether you wish to include redundancy for fault
tolerance. See “Power Management” on page 27 for more information.
Each power supply has its own power cord and power switch.
CAUTION—Never use the module handles to lift or move the Alcatel
Wireless LAN Switch chassis. Using the handles to support the
chassis can result in serious damage to both the module and the
chassis.
CAUTION—Never insert or remove a power supply while its power
switch is in the On (|) position or while the power cord is plugged in.
First verify the power switch is Off (|) and the cord is unplugged.
CAUTION—Be sure to exercise proper Electrostatic Discharge (ESD)
precautions when handling Alcatel 6000-series components.
3
4
5
6
7

OmniAccess 6000: Installation Guide
4Part 031639-00 May 2005

Installing the Chassis 5
CHAPTER 2
Installing the Chassis
This chapter covers the following installation topics:
zPrecautions to observe during installation
zRequirements for Alcatel Wireless LAN Switch components
and rack mounting gear
zSelecting a proper environment for the Alcatel Wireless LAN
Switch
zMounting the Alcatel Wireless LAN Switch in a rack
zConnecting power to the Alcatel Wireless LAN Switch
Pre-Installation Checklist
You will need the following during installation:
OmniAccess 6000 Wireless LAN Switch components (see
“Minimum Switch Configuration” on page 7).
OmniAccess 6000 rack mounting kit (see “Rack Mounting Kit”
on page 7).
Phillips or cross-head screwdriver.
19-inch equipment rack, or equivalent.
3U rack space with 10 cm (4 inches) clearance to the left,
right, front, and rear of the rack.
Another person to help position the switch.
Alcatel power cord for each power supply, rated to at least 10
A with IEC320 connector.
Adequate power supplies and electrical power (see “Power
Management” on page 27).
Cool, non-condensing air 0 to 40 ºC (32 to 104 ºF). May
require air conditioning.
Console terminal with RJ-45 or DB-9 serial port.
RS-232 serial cable with RJ-45 male connectors.
Alcatel serial adapter (included) if connecting to the console
with DB-9.
CAUTION—Installation should be performed by a trained technician.

OmniAccess 6000: Installation Guide
6Part 031639-00 May 2005
Precautions
CAUTION—Dangerous voltage in excess of 240VAC is always present
while the Alcatel Power Supply Module is plugged into an electrical
outlet. Remove all rings, jewelry, and other potentially conductive
material before working with this product.
Never insert foreign objects into the chassis, the power supply, or any
other component, even when the power supplies have been turned
off, unplugged, or removed.
Main power is fully disconnected from the Alcatel Wireless LAN
Switch by unplugging all installed power supplies’ power cords from
their power outlets. For safety reasons, verify the power outlets and
plugs are within easy reach of the operator.
Do not handle electrical cables which are not insulated. This includes
any network cables.
To minimize electrical hazard, keep water and other fluids away from
the product.
Comply with electrical grounding standards during all phases of
installation and operation of the product. Do not allow the Alcatel
Wireless LAN Switch chassis, network ports, power supplies, or
mounting brackets to contact any device, cable, object, or person
attached to a different electrical ground. Also, never connect the
device to external storm grounding sources.
Installation or removal of the chassis or any module must be
performed in a static-free environment. The proper use of anti-static
body straps and mats is strongly recommended.
Modules must be kept in anti-static packaging when not installed in
the chassis.
Do not ship or store this product near strong electromagnetic,
electrostatic, magnetic or radioactive fields.
Do not disassemble the chassis or any module. They have no internal
user-serviceable parts. When service or repair is needed, see
“Contacting Alcatel” on page xiii.