Alcatel-Lucent SFP User manual

060220-00 Rev. M
April 2011
OmniSwitch
Transceivers Guide
www.alcatel-lucent.com

ii OmniSwitch Transceivers Guide April 2011
This user guide contains SFP and XFP transceiver specifications and compatibility information for
the OmniSwitch 6250, 6850, 6850E, 6855, 6400, 9000, 9000E and the OmniStack 6200 Series of
switches . The information described in this guide is subject to change without notice.
Attention: Use of any transceivers other than those part numbers listed in the SFP and XFP
Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for
proper performance and may result in voiding the warranty for the affected platforms.
Copyright © 2011 by Alcatel-Lucent. All rights reserved. This document may not be reproduced in whole
or in part without the express written permission of Alcatel-Lucent.
Alcatel-Lucent®and the Alcatel-Lucent logo are registered trademarks of Alcatel-Lucent. Xylan®,
OmniSwitch®, OmniStack®, and Alcatel-Lucent OmniVista®are registered trademarks of Alcatel-Lucent.
OmniAccess™, Omni Switch/Router™, PolicyView™, RouterView™, SwitchManager™, VoiceView™,
WebView™, X-Cell™, X-Vision™, and the Xylan logo are trademarks of Alcatel-Lucent.
This OmniSwitch product contains components which may be covered by one or more of the following
U.S. Patents:
• U.S. Patent No. 6,339,830
• U.S. Patent No. 6,070,243
• U.S. Patent No. 6,061,368
• U.S. Patent No. 5,394,402
• U.S. Patent No. 6,047,024
• U.S. Patent No. 6,314,106
• U.S. Patent No. 6,542,507
• U.S. Patent No. 6,874,090
26801 West Agoura Road
Calabasas, CA 91301
[phone] FAX [phone]
[email protected]
US Customer Support—[phone]
Internet—[e-mail]

OmniSwitch Transceivers Guide April 2011 iii
Contents
About This Guide ...........................................................................................................v
Supported Platforms ...........................................................................................................v
Who Should Read this Manual? ........................................................................................vi
When Should I Read this Manual? ....................................................................................vi
What is Not in this Manual? ..............................................................................................vi
How is the Information Organized? .................................................................................vii
Documentation Roadmap .................................................................................................vii
Related Documentation .....................................................................................................ix
Product Documentation .....................................................................................................xi
Technical Support .............................................................................................................xi
Chapter 1 Small Form-Factor Pluggables (SFPs) ...................................................................1-1
In This Chapter ................................................................................................................1-1
SFP MSA Specification ..................................................................................................1-2
SFP Transceiver Installation and Removal .....................................................................1-3
Gigabit Ethernet Transceivers .........................................................................................1-5
Dual-Speed Ethernet Transceivers ..................................................................................1-8
Bi-directional Ethernet Transceivers ...............................................................................1-9
100 FX Ethernet Transceivers .......................................................................................1-12
CWDM Gigabit Ethernet Transceivers .........................................................................1-14
10-Gigabit SFP+ Transceivers ......................................................................................1-15
Chapter 2 Industrial Small Form Factor Pluggables (iSFPs) ............................................1-18
In This Chapter ..............................................................................................................1-18
Industrial Gigabit Ethernet Transceivers ......................................................................1-19
Industrial Bi-directional Ethernet Transceivers ............................................................1-22
Industrial 100 FX Ethernet Transceivers ......................................................................1-25
Industrial 10-Gigabit SFP+ Transceivers ......................................................................1-27
Chapter 3 10-Gigabit Small Form Factor Pluggables (XFPs) ..........................................1-28
In This Chapter ..............................................................................................................1-28
XFP MSA Specification ................................................................................................1-29

Contents
iv OmniSwitch Transceivers Guide April 2011
XFP Transceiver Installation and Removal ..................................................................1-30
10-Gigabit Ethernet Transceivers .................................................................................1-31
Chapter 4 SFP Compatibility Matrix ........................................................................................1-34
OmniSwitch 9000 Series ...............................................................................................1-34
OmniSwitch 9000E Series ............................................................................................1-35
OmniSwitch 6855 Series ...............................................................................................1-36
OmniSwitch 6850 Series ...............................................................................................1-37
OmniSwitch 6850E Series ............................................................................................1-38
OmniSwitch 6400 Series ...............................................................................................1-40
OmniSwitch 6250 Series ...............................................................................................1-41
OmniStack 6200 Series .................................................................................................1-42
Chapter 5 XFP Compatibility Matrix ........................................................................................1-43
OmniSwitch 9000 Series ...............................................................................................1-43
OmniSwitch 9000E Series ............................................................................................1-43
OmniSwitch 6855 Series ...............................................................................................1-44
OmniSwitch 6850 Series ...............................................................................................1-44
OmniSwitch 6400 Series ...............................................................................................1-44
OmniSwitch 6250 Series ...............................................................................................1-44
OmniStack 6200 Series .................................................................................................1-45

OmniSwitch Transceivers Guide April 2011 page v
About This Guide
This OmniSwitch Transceivers Guide provides specifications and compatibility information for the
supported OmniSwitch SFP and XFP transceivers for all OmniSwitch AOS 6 Release Products.
Attention: Use of any transceivers other than those part numbers listed in the SFP and XFP
Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for
proper performance and may result in voiding the warranty for the affected platforms.
Supported Platforms
This information in this guide applies to the following products:
•OmniSwitch 6250 Series
•OmniSwitch 6400 Series
•OmniSwitch 6850(E) Series
•OmniSwitch 6855 Series
•OmniSwitch 9000/9000E Series
•OmniStack 6200 Series
Unsupported Platforms
The information in this guide does not apply to the following products:
•OmniSwitch (original version with no numeric model name)
•OmniSwitch 6600 Series
•OmniSwitch 6800 Series
•OmniSwitch 7700/7800
•OmniSwitch 8800
•Omni Switch/Router
•OmniStack
•OmniAccess

Who Should Read this Manual? About This Guide
page vi OmniSwitch Transceivers Guide April 2011
Who Should Read this Manual?
The audience for this user guide is network administrators and IT support personnel who need to provide
network connectivity using SFP or XFP transceivers on an OmniSwitch.
When Should I Read this Manual?
Read this guide as soon as you are ready to integrate your OmniSwitch into your network and you are
ready to provide connectivity using the supported transceivers. You should have already stepped through
the first login procedures and read the brief software overviews in the appropriate OmniSwitch Getting
Started Guide and OmniSwitch Hardware Guide.
This guide includes information about the supported OmniSwitch transceivers.
•SFP and XFP specifications
•SFP and XFP compatibility information
What is Not in this Manual?
Procedures for switch management methods, such as CLI, web-based (WebView or OmniVista) or SNMP,
are outside the scope of this guide.
For information on WebView and SNMP switch management methods consult the OmniSwitch Switch
Management Guide. Information on using WebView and OmniVista can be found in the context-sensitive
on-line help available with those network management applications.
This guide is designed to provide transceiver specification and compatibility information only and is not
intended as a reference for any CLI commands or configuration information. Refer to the Documentation
Roadmap for a list of available user guides.

About This Guide How is the Information Organized?
OmniSwitch Transceivers Guide April 2011 page vii
How is the Information Organized?
Chapters in this guide are broken down by transceiver type, SFP or XPF. Additional sub-sections are
provided for the various types of transceivers.
Specification Information. Each transceiver has an associated table providing individual specifications
for all supported transceivers.
Compatibility Information. A compatibility chart is provided for each transceiver specifying which
modules or switch the transceiver is supported on.
Documentation Roadmap
The OmniSwitch user documentation suite was designed to supply you with information at several critical
junctures of the configuration process. The following section outlines a roadmap of the manuals that will
help you at each stage of the configuration process. Under each stage, we point you to the manual or
manuals that will be most helpful to you.
Stage 1: Using the Switch for the First Time
Pertinent Documentation: Getting Started Guides
Release Notes
The Getting Started Guide provides the basic information you need to unpack and identify the compo-
nents of your shipment. It provides information on unpacking the switch, unlocking access control, setting
the switch’s IP address, and setting up a password. It also includes overview information on fundamental
aspects of the switch, such as hardware LEDs, the software directory structure, CLI conventions, and web-
based management.
At this time you should also familiarize yourself with the Release Notes that accompanied your switch.
This document includes important information on feature limitations that are not included in other user
guides.
Stage 2: Gaining Familiarity with Basic Switch Functions
Pertinent Documentation: Hardware Users Guides
Switch Management Guide
OmniSwitch Transceivers Guide
Once you have your switch up and running, you will want to begin investigating basic aspects of its hard-
ware and software. Information about switch hardware is provided in the Hardware Guide. This guide
provide specifications, illustrations, and descriptions of all hardware components, such as chassis, power
supplies, Chassis Management Modules (CMMs), Network Interface (NI) modules, and cooling fans. It
also includes steps for common procedures, such as removing and installing switch components.
The Switch Management Guide is the primary users guide for the basic software features on a single
switch. This guide contains information on the switch directory structure, basic file and directory utilities,
switch access security, SNMP, and web-based management. It is recommended that you read this guide
before connecting your switch to the network.

Documentation Roadmap About This Guide
page viii OmniSwitch Transceivers Guide April 2011
Stage 3: Integrating the Switch Into a Network
Pertinent Documentation: Network Configuration Guide
Advanced Routing Configuration Guide
When you are ready to connect your switch to the network, you will need to learn how the OmniSwitch
implements fundamental software features, such as 802.1Q, VLANs, Spanning Tree, and network routing
protocols. The Network Configuration Guide contains overview information, procedures, and examples on
how standard networking technologies are configured in the OmniSwitch.
The Advanced Routing Configuration Guide includes configuration information for networks using
advanced routing technologies (OSPF and BGP) and multicast routing protocols (DVMRP and PIM-SM).
Anytime
The OmniSwitch CLI Reference Guide contains comprehensive information on all CLI commands
supported by the switch. This guide includes syntax, default, usage, example, related CLI command, and
CLI-to-MIB variable mapping information for all CLI commands supported by the switch. This guide can
be consulted anytime during the configuration process to find detailed and specific information on each
CLI command.

About This Guide Related Documentation
OmniSwitch Transceivers Guide April 2011 page ix
Related Documentation
The following are the titles and descriptions of all the related OmniSwitch AOS Release 6 user manuals:
•OmniSwitch 6250 Series Getting Started Guide
Describes the basic information you need to unpack and identify the components of your OmniSwitch
6250 shipment. Also provides information on the initial configuration of the switch.
•OmniSwitch 6400 Series Getting Started Guide
Describes the basic information you need to unpack and identify the components of your OmniSwitch
6400 shipment. Also provides information on the initial configuration of the switch.
•OmniSwitch 6850/6850E Series Getting Started Guide
Describes the basic information you need to unpack and identify the components of your OmniSwitch
6850(E) shipment.Also provides information on the initial configuration of the switch.
•OmniSwitch 6855 Series Getting Started Guide
Describes the basic information you need to unpack and identify the components of your OmniSwitch
6855 shipment. Also provides information on the initial configuration of the switch.
•OmniSwitch 9000/9000E Series Getting Started Guide
Describes the hardware and software procedures for getting an OmniSwitch 9000/9000E Series up and
running. Also provides information on fundamental aspects of OmniSwitch software architecture.
•OmniSwitch 6250 Series Hardware Users Guide
Detailed technical specifications and procedures for the OmniSwitch 6250 Series chassis and compo-
nents. Also includes comprehensive information on assembling and managing stacked configurations.
•OmniSwitch 6400 Series Hardware Users Guide
Detailed technical specifications and procedures for the OmniSwitch 6400 Series chassis and compo-
nents. Also includes comprehensive information on assembling and managing stacked configurations.
•OmniSwitch 6850/6850E Series Hardware User Guide
Complete technical specifications and procedures for all OmniSwitch 6850(E) Series chassis, power
supplies, and fans. Also includes comprehensive information on assembling and managing stacked
configurations.
•OmniSwitch 6855 Series Hardware User Guide
Complete technical specifications and procedures for all OmniSwitch 6855 Series chassis, power
supplies, and fans.
•OmniSwitch 9000/9000E Series Hardware Users Guide
Complete technical specifications and procedures for all OmniSwitch 9000/9000E Series chassis,
power supplies, fans, and Network Interface (NI) modules.
•OmniSwitch CLI Reference Guide
Complete reference to all CLI commands supported on the OmniSwitch Series switches. Includes
syntax definitions, default values, examples, usage guidelines and CLI-to-MIB variable mappings.

Related Documentation About This Guide
page x OmniSwitch Transceivers Guide April 2011
•OmniSwitch AOS Release 6 Switch Management Guide
Includes procedures for readying an individual switch for integration into a network. Topics include the
software directory architecture, image rollback protections, authenticated switch access, managing
switch files, system configuration, using SNMP, and using web management software (WebView).
•OmniSwitch AOS Release 6 Network Configuration Guide
Includes network configuration procedures and descriptive information on all the major software
features and protocols included in the base software package. Chapters cover Layer 2 information
(Ethernet and VLAN configuration), Layer 3 information (routing protocols, such as RIP), security
options (authenticated VLANs), Quality of Service (QoS), and link aggregation.
•OmniSwitch AOS Release 6 Advanced Routing Configuration Guide
Includes network configuration procedures and descriptive information on all the software features and
protocols included in the advanced routing software package. Chapters cover multicast routing
(DVMRP and PIM-SM), and OSPF.
•OmniSwitch Transceivers Guide
Includes SFP and XFP transceiver specifications and product compatibility information.
•Technical Tips, Field Notices
Includes information published by Alcatel-Lucent’s Customer Support group.
•Release Notes
Includes critical open Problem Reports, feature exceptions, and other important information on the
features supported in the current release and any limitations to their support.

About This Guide Product Documentation
OmniSwitch Transceivers Guide April 2011 page xi
Product Documentation
Some products are shipped with documentation included on a User Manual CD that accompanies the
switch. This CD also includes documentation for other Alcatel-Lucent data enterprise products.
All products are shipped with a Product Documentation Card that provides details for downloading docu-
mentation for all OmniSwitch and other Alcatel-Lucent data enterprise products.
All documentation is in PDF format and requires the Adobe Acrobat Reader program for viewing. Acro-
bat Reader freeware is available at www.adobe.com.
Note. In order to take advantage of the documentation CD’s global search feature, it is recommended that
you select the option for searching PDF files before downloading Acrobat Reader freeware.
To verify that you are using Acrobat Reader with the global search option, look for the following button in
the toolbar:
Note. When printing pages from the documentation PDFs, de-select Fit to Page if it is selected in your
print dialog. Otherwise pages may print with slightly smaller margins.
Technical Support
An Alcatel-Lucent service agreement brings your company the assurance of 7x24 no-excuses technical
support. You’ll also receive regular software updates to maintain and maximize your Alcatel-Lucent prod-
uct’s features and functionality and on-site hardware replacement through our global network of highly
qualified service delivery partners. Additionally, with 24-hour-a-day access to Alcatel-Lucent’s Service
and Support web page, you’ll be able to view and update any case (open or closed) that you have reported
to Alcatel-Lucent’s technical support, open a new case or access helpful release notes, technical bulletins,
and manuals. For more information on Alcatel-Lucent’s Service Programs, see our web page at
service.esd.alcatel-lucent.com, call us at 1-800-995-2696, or email us at esd.[email protected].

Technical Support About This Guide
page xii OmniSwitch Transceivers Guide April 2011

OmniSwitch Transceivers Guide April 2011 page 1-1
1 Small Form-Factor
Pluggables (SFPs)
OmniSwitch Series switches use both copper-based and fiber-based optical Small Form Factor Pluggable
(SFP) transceivers. SFPs are fully hot-swappable and are available for both short-reach and long-reach
applications. Copper-based and fiber-based optical SFPs can be mixed on the same module.
In This Chapter
This chapter describes the technical specifications for all the OmniSwitch supported SFP transceivers. For
additional details about OmniSwitch modules, see the appropriate OmniSwitch Hardware Guide.
SFP specifications in this chapter include:
•SFP MSA Specifications. See “SFP MSA Specification” on page 1-2
•SFP Transceiver Installation. See “SFP Transceiver Installation and Removal” on page 1-3
•Gigabit Ethernet Transceivers. See “Gigabit Ethernet Transceivers” on page 1-5.
•Dual-Speed Ethernet Transceivers. See “Dual-Speed Ethernet Transceivers” on page 1-8.
•Bi-directional Ethernet Transceivers. See “Bi-directional Ethernet Transceivers” on page 1-9.
•100-FX Ethernet Transceivers. See “100 FX Ethernet Transceivers” on page 1-12.
•CWDM Gigabit Ethernet Transceivers. See “CWDM Gigabit Ethernet Transceivers” on page 1-14.
•10-Gigabit SFP+ Transceivers. See “10-Gigabit SFP+ Transceivers” on page 1-15
For information on installing and managing OmniSwitch hardware, see the appropriate Hardware Guide.
For information on OmniSwitch SFP compatibility, see “SFP Compatibility Matrix” on page 4-34.
For information on OmniSwitch XFP compatibility, see “XFP Compatibility Matrix” on page 5-42.

SFP MSA Specification Small Form-Factor Pluggables (SFPs)
page 1-2 OmniSwitch Transceivers Guide April 2011
SFP MSA Specification
The Small Form-Factor Pluggable (SFP) MSA (Multi Source Agreement) is a specification for a common
interface for optical modular transceivers. The SFP connector consists of a 20-pin receptacle and an SFP
housing cage. The connector provides the interface for the hot pluggable SFP module. Each SFP module
contains a serial interface to provide identification information that describes the SFP capabilities, stand
interfaces, manufacturer and other information.
For information on installing SFPs, refer to the documentation included with the transceiver.
Small Form Factor Pluggable (SFP)
This diagram is a representation
only; the physical appearance of the
actual module may vary slightly.

Small Form-Factor Pluggables (SFPs) SFP Transceiver Installation and Removal
OmniSwitch Transceivers Guide April 2011 page 1-3
SFP Transceiver Installation and Removal
Follow the instructions below for the appropriate SFP type.
ESD Caution: Before handling the module, you must discharge all static electricity on your person to
avoid Electrostatic Discharge (ESD) damage. If using a wrist strap, ensure that the wrist strap touches
your skin. Attach the other end of the strap to the chassis. If your chassis provides a grounding lug, this
can be used. Refer to your hardware user guide for details.
If using a wrist strap, ensure that the wrist strap touches your skin. Attach the other end of the strap to the
chassis. If your chassis provides a grounding lug, this can be used. Refer to your hardware user guide for
details.
Dust Exposure: To reduce the risk of dust exposure and physical damage, be sure to replace the protec-
tive rubber cover (provided) when the SFP is not in use.
Eye Safety: SFP transceivers are international Class 1 laser products and are eye-safe devices when oper-
ated within the limits of manufacturers’ specifications. Operating SFP transceivers in a manner inconsis-
tent with intended usage and specification may result in hazardous radiation exposure.
Note: After removing a transceiver, wait for a minimum of 5 seconds before re-inserting any transceiver
into the same port. This allows sufficient time for software to detect the removal of the transceiver.
Note: Never force the transceiver in or out of the transceiver slot.
SFP - Hinged
To remove, you must first open the SFP’s hinged face to approximately ninety
degrees. Then, grasp the hinged face and carefully pull the SFP straight out of
the slot.
When inserting a SFP, be sure that the hinged face is closed. Slide the SFP
straight into the slot until the module clicks firmly into place.
SFP Module
Interface Slot

SFP Transceiver Installation and Removal Small Form-Factor Pluggables (SFPs)
page 1-4 OmniSwitch Transceivers Guide April 2011
SFP - Bail Wire
SFP - Ejector Button
To install, align the transceiver with the transceiver slot on the
NI module, as shown. Be sure that the bail wire delatch is in the
up, or closed position. Slide the transceiver straight into the slot
until the module clicks firmly into place.
SFP Transceiver
Network Interface (NI)
Module
To remove, you must first pull down on the bail
wire delatch. Grip the wire delatch while it is in this
open position and carefully pull the transceiver
straight out of the slot.
Bail Wire Delatch Transceiver Slot
(Shown in open “removal” posi-
tion; when inserting, bail
delatch must be closed.)
To install, align the transceiver with the
transceiver slot on the NI module, as
shown. Carefully slide the transceiver
back until it clicks into place; this is an
indication that the connectors are firmly
seated. SFP Transceiver
Network Interface (NI) Module
To remove, use the ejector tool (provided
with each switch chassis) to push the trans-
ceiver’s ejector button. The ejector button is
located just below the transceiver port; refer
to the diagram for more information. The
transceiver will disengage from the connec-
tors and eject slightly. Once disengaged, use
the clip end of the ejector tool to carefully
pull the transceiver straight out and away
from the NI module.
Dust Cover
Ejector
Transceiver Slot

Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers
OmniSwitch Transceivers Guide April 2011 page 1-5
Gigabit Ethernet Transceivers
SFP-GIG-SX
Gigabit SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3z, SFP MSA
Connections Supported 1000Base-SX
Fiber Type MMF
Wavelength 850 nm
Optical Power Output -9.5 to -4 dBm
Receiver Sensitivity -17 dBm
Transmission Distance ~275 m on 62.5/125µm
~550 m on 50/125µm
Operating Temperature 0 ºC to 70 ºC
Digital Diagnostic Monitoring Not Supported
SFP-GIG-LX
Gigabit SFP Optical Transceiver.
Connector types LC
Standards supported 802.3z, SFP MSA
Connections supported 1000Base-LX
Fiber Type SMF
Wavelength 1310 nm
Optical Power Output -9.5 to -3 dBm
Receiver Sensitivity -20 dBm
Transmission Distance ∼10 km
Operating Temperature -40 ºC to 85 ºC / 0 ºC to 70 ºC
Digital Diagnostic Monitoring Not Supported

Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFPs)
page 1-6 OmniSwitch Transceivers Guide April 2011
Gigabit Ethernet Transceivers (cont.)
SFP-GIG-LH70
Gigabit SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3z, SFP MSA
Connections Supported 1000Base-LH70
Fiber Type SMF
Wavelength 1550 nm
Optical Power Output 0 to +5 dBm
Receiver Sensitivity -22 dBm
Transmission Distance ~70 km
Operating Temperature 0 ºC to 70 ºC
Digital Diagnostic Monitoring Supported
SFP-GIG-LH40
Gigabit SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3z, SFP MSA
Connections Supported 1000Base-LH40r
Fiber Type SMF
Wavelength 1310 nm
Optical Power Output -2 to +3 dBm
Reciever Sensitivity -22 dBm
Transmission Distance ~40 km
Operating Temperature 0 ºC to 70 ºC
Digital Diagnostic Monitoring Supported

Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers
OmniSwitch Transceivers Guide April 2011 page 1-7
Gigabit Ethernet Transceivers (cont.)
SFP-GIG-EXTND
Gigabit SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3z, SFP MSA
Connections Supported 1000Base-SX
Fiber Type MMF
Wavelength 850 nm
Optical Power Output -
Receiver Sensitivity -
Transmission Distance ~2 km
Operating Temperature 0 ºC to 70 ºC
Digital Diagnostic Monitoring Supported
SFP-GIG-T
Gigabit SFP Copper Transceiver.
Connector Type RJ-45
Standards Supported 802.3z, SFP MSA
Connections supported 1000Base-T
Cable Type CAT5, CAT5e, CAT6
Transmission Distance ∼100 m
Digital Diagnostic Monitoring Not Supported

Dual-Speed Ethernet Transceivers Small Form-Factor Pluggables (SFPs)
page 1-8 OmniSwitch Transceivers Guide April 2011
Dual-Speed Ethernet Transceivers
SFP-DUAL-MM
Dual-Speed SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3z, 802.3ah, SFP MSA
Connections Supported 100Base-FX, 1000Base-LX
Fiber Type MMF
Wavelength 1310 nm
Average Power Output 100Base-FX: -20 to -14 dBm
1000Base-LX: -11.5 to -3 dBm
Receiver Sensitivity 100Base-FX: -28 dBm
1000Base-LX: -22 dBm
Transmission Distance 550 m at 1000 Mbps
2 km at 100 Mbps
Operating Temperature 0 ºC to 70 ºC
Digital Diagnostic Monitoring Not Supported
SFP-DUAL-SM10
Dual-Speed SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3z, 802.3ah, SFP MSA
Connections Supported 100Base-FX, 1000Base-LX
Fiber Type SMF
Wavelength 1310 nm
Average Power Output 100Base-FX: -15 to -8 dBm
1000Base-LX: -9.5 to -3 dBm
Receiver Sensitivity 100Base-FX: -28
1000Base-LX: -22
Transmission Distances 10 km
Operating Temperature 0 ºC to 70 ºC
Digital Diagnostic Monitoring Not Supported