Alcatel OmniAccess 6000 User manual

Alcatel OmniAccess 6000 400W Power Supply Unit Installation Instructions 1
Alcatel OmniAccess 6000
400W Power Supply Unit
Installation Instructions
The 400W Power Supply Unit (OAW-6000-PS400W) is a field
replaceable, hot-swappable component for the Alcatel
OmniAccess 6000 Wireless LAN Switch series. Before installing
the 400W PSU, make sure you understand this procedure and all
precautions.
The OAW-6000-PS400 supports Power over Ethernet (POE),
Serial Power over Ethernet (SPOE), and non-POE enabled line
cards.
The 400W PSU components are:
1. Captive screws (2)
2. Unit handle used to insert or remove the power supply
O.T.P
DC OK
AC OK
176541 2 3
6.5A MAX

OmniAccess 6000 400W PSU Installation Notes: Installation Guide
2Part 031655-00 May 2005
3. LEDs
When installed correctly, the bottom LED (AC OK) and the middle LED (DC OK)
should be green. The top LED (OTP - Over Temperature Protection) should be
off. For more information on the LEDs refer to the installation guide.
4. Fan intake vent
5. Power Cord Retaining Clip
6. Power connector
7. Power On/Off Switch - Off (|) and On (|)
To Install the 400W PSU
1. Select a power supply slot for the power supply.
The 400 W power supply (OAW-6000-PS400) can be installed in any of the
three slots.
CAUTION—Do not use the handle to lift the Alcatel Wireless LAN
switch.

Alcatel OmniAccess 6000 400W Power Supply Unit Installation Instructions 3
If you are replacing a previously installed power supply, turn it off and unplug it.
Use a #2 Phillips or cross-head screwdriver to turn the power supply’s captive
fastening screws counter-clockwise until they are loose (they cannot be
completely removed). Firmly grasp the handle of the power supply and
carefully pull the module out of the switch’s power supply slot.
If you are installing a power supply in an empty slot, you may have to remove
the blank cover plate first. To do this, use a #2 Phillips or cross-head
screwdriver. Turn the captive fastening screws on the faceplate
counter-clockwise until they are loose (they cannot be completely removed).
Remove the cover plate and store it in a safe place.
2. Make sure the power switch on the power supply to be installed is Off
(|).
3. Insert the power supply into the chassis.
Grasp the power supply by handle, keeping the LEDs on the left and power
switch on the right. Align the back of the module with the guide-rails in the
chassis power supply slot and gently slide in the module. Do not force the
module; it should slide in easily most of the way. There may be moderate
resistance when the power supply meets the connectors at the back of the
chassis. Press firmly to engage the connectors, but do not use excessive force.
4. Secure the power supply.
Use the screwdriver to push in the module’s captive fastening screws and turn
them clockwise until moderate resistance is felt. Do not over-tighten.
CAUTION—Do not mix 200W and 400W PSUs in the same chassis.
Adding a 200W PSU causes the switch to read installed 400W PSUs
as 200W PSUs. Since 200W power supplies do not support POE,
adding a 200W power supply disables POE.
CAUTION—Never insert or remove a power supply while its power
switch is in the On (|) position. Make sure the power switch is Off (|)
first.

OmniAccess 6000 400W PSU Installation Notes: Installation Guide
4Part 031655-00 May 2005
5. Attach the power cord to the power supply.
Plug an appropriate power cord into the power input socket. The socket
accepts a power cord with a standard IEC320 plug.
6. Attach the power cord to a proper electrical outlet.
Make sure that your site’s electrical systems can handle the switch’s power
load.
Each power supply (OAW-6000-PS400) is rated at 400 W total and is
auto-ranging to accept 85 to 264 VAC, at 50 to 60 Hz.
Depending on the switch’s total power load, you may be required to increase
the capacity of your site’s electrical systems. Refer to the installation guide for
information on maximum power load, use of a UPS, and the like.
CAUTION—For proper safety and performance, the power cord must be
rated to 10 A and conform to grounded electrical standards in the
country where the product is operated.

Alcatel OmniAccess 6000 400W Power Supply Unit Installation Instructions 5
Contacting Alcatel
Web Site
Telephone Numbers
zMain Site http://www.alcatel.com
zSupport http://www.alcatel.com/enterprise
zMain US/Canada [phone]
zMain Outside US [phone]

OmniAccess 6000 400W PSU Installation Notes: Installation Guide
6Part 031655-00 May 2005