Alexor PC9155-433 User manual

N11427
IMPORTANT: This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer. The entire manual
should be carefully read.
2-Way Wireless Security Suite
User Manual

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digit-
al Security Controls could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interfer-ence in a residential in-
stallation. This equipment generates, uses and can radiate radio frequency ener-
gy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occurin a particularinstallation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to cor-
rect the interference by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult a dealer or experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: ’How to
Identify and Resolve Radio/Television Interference Problems’. This booklet is
available from the U.S. Government Printing Office, Washington D.C. 20402,
Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the product was
approved July 23, 2001 or later, the requirements adopted by the ACTA. On the
top side of this equipment is a label that contains, among other information, a
product identifier. If requested, this number must be provided to the Telephone
Company.
Product Identifier: US:F53AL01B9155
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and tele-
phone network must comply with the applicable FCC Part 68 rules and require-
ments adopted by the ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible mod-
ular jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to
a telephone line. Excessive RENs on a telephone line may result in the devices
not ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local
Telephone Company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format US:
AAAEQ##TXXXX. The digits represented by ## are the REN without a deci-
mal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately
shown on the label. REN = 0.1B
Incidence of Harm
If this equipment (PC9155-433) causes harm to the telephone network, the tel-
ephone company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice is not practical, the Telephone
Company will notify the customer as soon as possible. Also, youwill be advised
of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, opera-
tions or procedures that could affect the operation of the equipment. If this hap-
pens the Telephone Company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment (PC9155/WT5500) for repair or
warranty information, contact the facility indicated below. If the equipment is
causing harm to the telephone network, the Telephone Company may request
that you disconnect the equipment until the problem is solved. This equipment
is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public
utility commission, public service commission or corporation commission for
information.
Alarm dialling equipment must be able to seize the telephone line and place a
call in an emergency situation. It must beable to do this even if other equipment
(telephone, answering system, computermodem, etc.) already has the telephone
line in use. To do so, alarm dialling equipment must be connected to a properly
installed RJ-31X jack that is electrically in series with and ahead of all other
equipment attached to the same telephone line. Proper installation is depicted in
the figure below. If you have any questions concerning these instructions, you
should consult your telephone company or a qualified installer about installing
the RJ-31X jack and alarm dialling equipment for you.
INDUSTRY CANADA STATEMENT
NOTICE: This product meets the applicable Industry Canada technical spec-
ifications.
Le présent materiel est conforme aux specifications techniques applicables d’In-
dustrie Canada.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.
L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.
The Ringer Equivalence Number is an indication of the maximum number of de-
vices allowed to be connected to a telephone interface. The termination on an in-
terface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does not exceed five.
L’indice d’équivalence de la sonnerie
(IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés
à une interface téléphonique. La terminaison d’une interface peut consister en
une combinaison quelconque de dispositifs, à la seule condition que la somme
d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
The term ’IC:’ before the radio certification number only signifies that Industry
Canada technical specifications were met.
Certification Number IC: 160A-PC9155
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Telephone
Computer
Telephone
Telephone
Fax Machine
Alarm Dialing
Equipment
RJ-31X
Jack Unused
RJ-11 Jack
Telephone
Line
Network
Service
Provider's
Facilities
Customer Premises Equipment and Wiring
Unused
RJ-11 Jack
Network
Demarcation
Point Answering
System
New Zealand - The following is a list of warnings applicable when this equipment is connected to the New Zealand Telecom Network.
General Warning
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that theitem com-
plies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor
does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects
with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is com-
patible with all of Telecom's network services.
Reverse Numbering (decadic signalling)
This equipment must not be programmed for decadic (pulse) dialling because its characteristics are incompatible with
the telephone exchanges in New Zealand. DTMF (tone) dialling is considerably faster and is fully compatible.
Line Grabbing Equipment
This equipment is set up to carry out test calls at pre-determined times. Such test calls will interrupt any other calls that
may be set up on the line at the same time. The timing set for such test calls should be discussed with the installer.
The timing set for test calls from this equipment may be subject to 'drift'. If this proves to be inconvenient and your calls
are interrupted, then the problem of timing should be discussed with the equipment installer. The matter should NOT be
reported as a fault to Telecom Faults Service.
D.C. Line Feed to Other Devices
During dialling, this device unit does not provide DC voltage to the series port connection and this may cause loss of
memory functions for the terminal devices (local telephone) connected to T-1, R-1.
General Operation (ringer sensitivity and loading)
This device only responds to Distinctive Alert cadences DA1 and DA2. DA1 is the normal ringing cadence.
These DSC Security Alarm
Systems may be connected
to the Telecom Network
PTC 211 / 09 /017 PC9155-433
PTC 211 / 09 /019 PC9155G-433
TELEPERMIT
RN = 0.5
PTC 211 / 09 /018 PC9155D-433

i
Table of Contents
About Your Security System 1
Fire / CO Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
General System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Keypad Controls & Indicators 2
Language Selection 2
Arming & Disarming the System 2
Stay Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Night Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Silent Exit Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Quick Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Siren Sounds After Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Remote Arming and Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Emergency Keys 4
When Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Intrusion (Burglary) Alarm Continuous Siren . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Fire Alarm Pulsed Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Carbon Monoxide Alarm 4
Time & Date Programming 4
Bypassing Zones 5
Trouble Conditions 6
Alarm Memory 6
Door Chime 6
Access Code Programming 7
Access Codes [4][5][Master Code]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
User Code Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Inherent Attributes (all codes except installer) . . . . . . . . . . . . . . . . . . . . . . . . . .7
Zone Bypassing Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Bell/Siren Squawk Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Erasing an Access Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Proximity Tag Enrollment 8
User Function Commands 9
Changing Brightness/Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Ambient Light Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Changing the Buzzer Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Viewing the Event Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Late to Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2-Way Wireless Key (WT4989, WT8989) . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
WT4989/WT8989 Status Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Keylock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Testing Your System 11
Siren and Keypad Display Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Walk Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Allowing Computer Access to your System . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Reference Sheets 12
Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Sensor / Zone Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Keypad Quick Guide 14
Guidelines for Locating Smoke / CO Detectors 15
Household Fire Safety Audit 17
Fire Escape Planning 17

ii
Always ensure you obtain the latest version of the User Guide. Updated versions of this
User Guide are available by contacting your distributor.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock and/or injury, observe the following:
• Do not spill any type of liquid on the equipment.
• Do not attempt to service this product yourself. Opening or removing the cover may
expose you to dangerous voltage or other risk. Refer servicing to qualified service per-
sonnel. Never open the device yourself.
• Do not touch the equipment and its connected cables during an electrical storm; there
may be a risk of electric shock from lightning.
• Do not use the Alarm System to report a gas leak if the system is near a leak.
REGULAR MAINTENANCE AND TROUBLESHOOTING
Keep your Alarm Controller in optimal condition by following all the instructions that are
included within this manual and/or marked on the product.
CLEANING
• Clean the units by wiping with a damp cloth only.
• Do not use abrasives, thinners, solvents or aerosol cleaners (spray polish) that may enter
through holes in the units of the Alarm Controller and cause damage.
• Do not use any water or any other liquid.
• Do not wipe the front cover with alcohol.
TROUBLESHOOTING
Occasionally, you may have a problem with your Alarm Controller or telephone line. If this
happens, your Alarm Controller will identify the problem and displays an error message.
Refer to the provided list when you see an error message on the display. If additional help
is required, contact your distributor for service.
WARNING: This equipment, PC9155 Alarm System shall be installed and used within an
environment that provides the pollution degree max 2 and over-voltages category II non-
hazardous locations, indoor only. It is designed to be installed, serviced and/or repaired by
service persons only [service person is defined as a person having the appropriate techni-
cal training and experience necessary to be aware of hazards to which that person may be
exposed in performing a task and of measures to minimize the risks to that person or other
persons]. For EU and Australian markets, the equipment is permanently connected; an
accessible disconnect device shall be incorporated into the building installation wiring. For
North America the equipment is a direct plug-in connection; the socket outlet shall be
installed near the PC9155 and shall be easily accessible. The plug of the direct plug-in
transformer serves as the disconnect device.
NOTE: There are no parts replaceable by the end-user within this equipment, except for the
keypad batteries and the WT4901/8901 batteries.
This publication covers the following models:
• PC9155-433 • PC9155D-868 • WT5500-868 • WT4989
• PC9155D-433 • PC9155G-868 • WT5500P-868 • WT8989
• PC9155G-433 • WT5500-433 • PT4 • WT4901
• PC9155-868 • WT5500P-433 • PT8 • WT8901
NOTE: Only these models shall be used with UL/ULC listed systems: PC9155-433,
PC9155D-433, PC9155G-433, WT5500P-433, WT5500-433, WT4901, WT4989 and PT4.
NOTE: The 868 MHz models are not UL/ULC listed.

1
About Your Security System
Read this manual carefully and have your installer instruct you on your system's operation and
on which features have been implemented in your system. All users of this system should be
fully instructed in its use. Fill out the ’System Information’ page with all of your zone information
and access codes, and store this manual in a safe place for future reference.
NOTE: Please consult your installer for further information regarding the false alarm reduction
features built into your system, as not all are covered in this manual.
Fire Detection (must be enabled by Installer)
This equipment is capable of monitoring fire detection devices such as smoke detectors and
providing a warning if a fire condition is detected. Good fire detection depends on having an
adequate number of detectors placed in appropriate locations. This equipment should be
installed in accordance with NFPA 72 (N.F.P.A., Batterymarch Park, Quincy MA 02269). Please
read the Family Escape Planning guidelines in this manual.
Carbon Monoxide Detection (must be enabled by Installer)
This equipment is capable of monitoring carbon monoxide detectors and providing a warning if
carbon monoxide is detected. Please read the Family Escape Planning guidelines in this manual
and instructions that are available with the carbon monoxide detector.
Te s t i n g
To ensure that your system continues to function as intended, you must test your system weekly.
Please refer to the ‘Testing your System’ section in this manual. If your system does not function
properly, call your installing company for service.
Monitoring
This system is capable of transmitting alarms, troubles, and emergency information to a central
station. If you initiate an alarm by mistake, immediately call the central station to prevent an
unnecessary response.
NOTE: The monitoring function must be enabled by the installer before it can become functional.
NOTE: This system has a communicator delay of 30 seconds. This function can be deleted, or it
can be increased up to a maximum of 45 seconds by the installer.
NOTE: Ensure that your installer verifies that your system is compatible with the Central Station
Receiver format at yearly intervals.
Maintenance
With normal use, the system requires minimum maintenance. Note the following points:
• Do not wash the security equipment with a wet cloth. Light dusting with a slightly moistened
cloth should remove normal accumulations of dust.
• The standby battery shall be replaced every 4-5 years by service persons only.
NOTE: Do not attempt to replace the battery or open the enclosure; there is a risk of electric
shock and/or fire.
• For other system devices such as smoke detectors, motion detectors, glassbreak detectors or
door/window contacts, consult the manufacturer’s literature for testing and maintenance
instructions.
General System Operation
Your security system includes an alarm control/keypad and various sensors and detectors. The
keypad is mounted by the main entry/exit location.
The security system has several zones of area protection. Each of these zones communicates to
a single wireless sensor (motion detectors, glassbreak detectors, door contacts, etc.) or to one
or more hard-wired sensors. A sensor in alarm is indicated by messages on the LCD.
Additional features include Automatic Inhibit (Swinger Shutdown) for Alarm; Tamper and Trouble
signals after 3 occurrences in a given set period; and a Programmable Keypad Lockout option.
For SIA CP-01 classified installations, the swinger shutdown feature is programmed such that
one or two trips will shut down the zone. The zone will be restored after a manual reset (by enter-
ing the access code at the time of disarming the alarm system) or it will be reset automatically
after 48 hours with no trips on any zones.
NOTE: Only the installer or service professional should have access to the system.

2
Keypad Controls & Indicators
IMPORTANT NOTICE
A security system cannot prevent emergencies. It is only intended to alert you and your central
station (if applicable) to an emergency situation. Security systems are generally very reliable but
they may not work under all conditions and they are not a substitute for prudent security prac-
tices or life and property insurance. Your security system must be installed and serviced by qual-
ified security professionals. These professionals can instruct you on the level of protection that
has been provided and on system operations.
Language Selection
Your system can display messages in different languages.
1. Press and hold both buttons simultaneously for 2 seconds.
2. Using the buttons, scroll through the available languages.
3. Press to select your desired language.
Arming and Disarming the System
Stay Arming
Stay arming will bypass the interior protection (i.e., motion sensors) and arm the perimeter of the
system (i.e., doors and windows). Close all sensors (i.e., stop motion and close doors). The
Ready ( ) indicator will illuminate.
Press and hold the Stay button until it beeps (approx. 2 seconds), enter your access code
or present your prox tag; do not leave the premises. During the setting state (exit delay active),
the Armed ( ) and Ready ( ) indicators will illuminate.
When the exit delay is completed, the alarm system is armed/set and this is indicated on the
keypad as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on.
The Armed ( ) indicator and a bypass message will be displayed. The system will automati-
cally ignore bypassed zones (i.e., motion sensors).
NOTE: For SIA CP-01 listed panels, the Stay Arming Exit Delay will be twice as long as the Away
Arming Exit Delay.
NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm
Reduction, then the security system will arm in the Stay Armed mode if the exit delay time expires
and no exit has been made.
Night Arming
To night arm the system when it has been armed in Stay Mode, press at the keypad. All
interior zones will now be armed except for devices programmed as Night Zones.
NOTE: Your installer can also program a function key on the keypad to allow you to arm the
system in Night Mode. This allows Night Arming to be activated by holding down the function key
for 2 seconds.
Night zones are only armed in Away mode; this permits limited movement within the premises
when the system is fully armed. Ensure that your installer has provided you with a list identifying
zones programmed as night zones.
System is
Ready to Arm
<>
Function
Keys
LED Indicators
Ready
Armed
Tr o uble
AC Power
Scroll Keys
Ambient Light
Sensor
LCD
Emergency Keys
Fire
Auxiliary
Panic
< > indicatesuser can
scroll through options
DG009033
123
456
789
0#
*
,
,

3
When the interior zones are activated (i.e., ) you must enter your access code or pres-
ent your proximity tag to disarm the system in order to gain access to interior areas that have not
been programmed as night zones.
Silent Exit Delay
If the system is armed using the Stay button or using the ’No Entry’ Arming method (
[Access Code]), the keypad buzzer will be silenced and the exit time will be doubled for that exit
period only.
Away Arming
Close all sensors (i.e., stop motion and close doors). The Ready ( ) indicator should be on.
To arm, press and hold the Away button for 2 seconds and/or enter your access code, present
your prox tag or press to Quick Arm.
During the setting state (exit delay active) the Armed ( ) and Ready ( ) indicators will turn on,
and the keypad will sound one beep per second. You now have ___ seconds to leave the prem-
ises (please check with your installer to have this time programmed). A keypad buzzer, whose
pulsating rate is distinct, will sound during the last ten seconds of the exit delay to warn per-
son(s) that the exit delay is running out. To cancel the arming sequence, enter your access code
or present your prox tag.
When the exit delay is completed, the alarm system is armed and this is indicated on the keypad
display as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on
and the keypad will stop sounding.
The system can also be armed/disarmed with a wireless key and with prox tags. Refer to the
‘Proximity Tags’ and ‘Two-Way Wireless Key’ sections for more details.
NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm
Reduction, the following holds true: Violation and restoral, followed by a second violation of the
entry/exit zone before the end of the exit delay, will restart the exit delay.
Quick Exit
If the system is armed and you need to exit, use the Quick Exit function to avoid disarming and
rearming the system. Press and hold the Quick Exit button for 2 seconds or press .
You now have 2 minutes to leave the premises. When the door is closed again, the remaining
exit time is cancelled.
Siren Sounds After Away Arming
Audible Exit Fault
In order to reduce false alar ms, the Audible Exit Fault is designed to notify you of an improper
exit when arming the system. If you fail to securely close the entry/exit door during the pro-
grammed exit delay period, the system will sound the alarm to indicate an improper exit (your
installer will tell you if this feature has been enabled on your system). If this occurs:
1. Re-enter the premises.
2. Enter your access code or present your prox tag, before the entry delay timer expires, to dis-
arm the system.
3. Repeat the Away arming procedure, ensuring that the entry/exit door(s) are secured.
Arming Error
An error tone will sound if the system is unable to arm. This will happen if the system is not ready
to arm (i.e., sensors are open), or if an incorrect user code has been entered. If this happens,
ensure all sensors are secure, press and try again.
Disarming
To disarm an armed system (Armed ( ) indicator is On), enter your access code or present your
prox tag. If your keypad is in sleep mode, press any key to wake it up then enter your access
code/present prox tag. The keypad will sound a continuous tone after the entry delay has been
initiated by opening the entry/exit door. Enter your code within _______ seconds to avoid an
alarm condition (check with your installer to have this time programmed).
Disarming Error
If your code/prox tag is invalid, the system will not disarm and a 2-second error tone will sound.
If this happens, press and try again.
,
,
,
,

4
Remote Arming and Disarming
The system can be armed and/or disarmed, if programmed by the installer, using a remote control
device (wireless key fob). When arming the system using the Arm button on a wireless key, the sys-
tem will acknowledge the command by sounding a single bell/siren squawk, if programmed to do
so by the installer. When disarming using the disarm button on a wireless key, the system will
acknowledge the command by sounding two bell/siren squawks. Three squawks, when disarming
with the disarm button, indicates that an alarm occurred while the system was armed. If you are
unsure of the cause of the alarm, proceed with caution (see section on 2-way Wireless Keys).
Emergency Keys
Press the (Fire), (Auxiliary), or (Panic) button for 2 seconds to generate a Fire,
Auxiliary, or Panic alarm. The keypad buzzer will beep indicating that the alarm input has been
accepted and transmission to the central station is underway. The button may or may not
sound the siren depending on installer setup.
NOTE: The Fire button can be disabled by the installer.
NOTE: The Auxiliary Alarm button is not intended to be used for medical signals.
When Alarm Sounds
The system can generate 3 different alarm sounds:
• Continuous Siren = Intrusion/Burglary Alarm
• Temporal / Pulsed Siren = Fire Alarm
• 4 beeps, 5-second pause, 4 beeps = Carbon Monoxide alarm
NOTE: The priority of signals is fire alarm, carbon monoxide alarm then burglary alarm.
Intrusion (Burglary) Alarm Continuous Siren
If you are unsure of the source of the alarm, proceed with caution! If the alarm was accidental,
enter your access code or present your prox tag to silence the alarm. If the alarm system is dis-
armed within the programmed Abort Window (check with the installer if this option has been en-
abled on your system and what is the transmitter delay time programmed), no alarm transmission
to the Central Station will occur. Following the Abort Window there appears a 5-minute Cancel
Window, during which a user can cancel, by entering their access code or presenting their prox
tag, an alarm that has been previously transmitted. A cancel signal will be transmitted to the cen-
tral station and the alarm system will also announce that the cancel signal was transmitted. Call
your central station to avoid a dispatch.
Fire Alarm Pulsed Siren
Follow your emergency evacuation plan immediately!
If the fire alarm was accidental (burned toast, bathroom steam, etc.), enter your access code or
present your prox tag to silence the alarm. Call your central station to avoid a dispatch.
Carbon Monoxide Alarm
Activation of your CO alarm indicates the presence of carbon monoxide (CO), which can be
fatal. During an alarm, the red LED on the CO detector flashes rapidly and buzzer sounds with a
repeating cadence of: 4 quick beeps, 5-second pause, 4 quick beeps. If an alarm sounds:
1. Operate silence button.
2. Call emergency services or your fire department.
3. Immediately move outdoors or to an open door/window.
WARNING: Carefully review your Carbon Monoxide Installation/User Guide to determine the nec-
essary actions required to ensure your safety and ensure that the equipment is operating correctly.
Incorporate the steps outlined in the guide into your evacuation plan.
Time & Date Programming
Press then your master access code to enter User
Functions. Use the buttons to find the menu option,
then press to select. Enter the time in 24-hr. format
(HH:MM), followed by the date (MM:DD:YY). Press to exit
programming. If you are viewing a ‘Loss of Clock’ trouble from within the trouble menu ( ),
press to directly enter Date and Time programming (see Trouble Conditions).
NOTE: Your installer may have programmed your system to display the time and date while the
keypad is idle. Press the button to temporarily clear the date and time display if desired.
HH:MM MM/DD/YY
09:06 01/31/09
,
,
,
,

5
Bypassing Zones
Use the zone bypassing feature when you need access to a protected area while the system is
armed, or when a zone is temporarily out of service but you need to arm the system. Bypassed
zones will not be able to sound an alarm. As a result, bypassing zones reduces the level of
security. If you are bypassing a zone because it is not working, call a service technician immedi-
ately so that the problem can be resolved and your system returned to proper working order.
Ensure that no zones are unintentionally bypassed when arming your system. Zones cannot be
bypassed once the system is armed. Bypassed zones (except for 24-hr zones) are automatically
cancelled each time the system is disarmed and must be bypassed again, if required, before
the next arming.
With the system disarmed:
Activating All Bypassed Zones
To remove bypass (all zones):
1. Press , then your access code or present your prox tag if required.
2. Press .
3. To exit bypassing mode and return to the Ready state, press .
Recalling Bypassed Zones
To recall the last set of bypassed zones:
1. Press , then your access code or present your prox tag if required.
2. Press .
3. To exit bypassing mode and return to the Ready state, press .
Bypass Group
A Bypass Group is a selection of zones programmed into the system. If you bypass a group of
zones on a regular basis, you can program them into a Bypass Group, so that you do not have to
bypass each zone individually. Note that only one Bypass Group can be programmed at a time.
To program a Bypass Group:
1. Press , then your access code or present your prox tag if required.
2. Enter the 2-digit numbers (01-34) of the zones to be included in the Bypass Group or use the
buttons to find the zone to be included in the Bypass Group, then press to
select the zone.
3. To save the selected zone into the group, press .
4. To exit bypassing mode and return to the Ready state, press .
NOTE: If an access code is required to enter bypassing, only the master code and codes with
Supervisory enabled can set the Bypass Group.
To select a Bypass Group when arming the system:
1. Press , then your access code or present your prox tag (if necessary).
2. Press . The next time the system is armed, the zones in this group will be bypassed.
3. To exit bypassing mode and return to the Ready state, press .
NOTE: A Bypass Group is only recalled if the system is armed/disarmed after programming the
Bypass Group.
NOTE: This feature is not to be used in UL Listed installations.
1. Press to enter the function menu. The keypad will display the
screen on the right.
2. Press or .
3. If your system is programmed to require access codes the screen
on the right will be displayed. Enter your 4-digit access code.
4. Scroll to the desired zone number using the keys, then
press to select the zone or directly enter the 2-digit number
of the zone you wish to bypass (e.g., 0 5 for zone 5).
,
,
Press (*) for <>
Zone Bypass
,
Enter Your
Access Code
Scroll to <>
Bypass Zones
,
,
,
,
,

6
Trouble Conditions
When a trouble condition is detected, the Trouble ( ) indicator will turn on and the keypad will
beep every 10 seconds. Press the button to silence the beeps. Press to view the
trouble condition. The Trouble ( ) indicator will flash. Use the scroll keys to view troubles.
Alarm Memory
When an alarm occurs, the Alarm Memory message will be displayed. To view which sensor(s)
generated the alarm, press .
For the system keypad use the scroll buttons to view the sensors in alarm memory. Press
to exit. To clear the memory, arm and disarm the system. If an alarm sounded while armed,
the system will automatically go to alarm memory when you disarm the system. In this instance,
you should proceed with caution, as the intruder may still be within the building/premises.
Door Chime
To turn the door chime function on or off, press and hold the Chime button for 2 seconds or
press . The system will sound 3 beeps to indicate the door chime is on, or one long tone
to indicate that door chime is off.
Trouble Comments Action
Alternate
Communicator Trouble
I ndicates SIM Card Lock, GSM Trouble, Ethernet Trouble,
Central Station Receiver Trouble, Supervision Trouble,
and SMS Config Trouble. Press to scroll
through individual troubles.
Call for service.
For Ethernet Trou-
ble check LAN con-
nections.
Service Required
(Press [1] for more
information)
Indicates Low Battery, System Trouble, System Tamper
or RF Jam detected.
Call for service.
Loss of AC Power If the building and/or neighbourhood has lost electrical
power, the system will continue to operate on battery
power for several hours.
Check AC
connection.
Call for service.
Telephone Line Fault The system has detected that the telephone line is dis-
connected.
Call for service.
Failure to
Communicate
The system attempted to communicate with the monitor-
ing station but failed. This may be due to a Telephone
Line Fault.
Call for service.
Module/Sensor Fault The system is experiencing difficulties with one or more
module/sensor on the system. Continue to press to
navigate through the Zone, Keypad, and Siren fault
menus.
Call for service.
Module/Sensor Tamper The system has detected a tamper condition with one or
more module/sensor on the system. Continue to press
to navigate through the zone, keypad, and siren
tamper menus.
Call for service.
Module/Sensor Low
Battery
The system has detected a low battery condition with
one or more module/sensor on the system. Continue to
press to display the zone(s), wireless key(s), key-
pad(s), siren(s) and prox tag(s).
See section on
Siren Test. Call for
service.
Loss of Time & Date If complete power was lost (AC and Battery), the time
and date will need to be re-programmed. Press .
Reprogram Time &
Date.
Blank Display/No
Response
Keypad battery may have discharged beyond the usable
level.
Replace battery
(call for service if
trouble not cleared).
"Panel Response Not
Received" message
The keypad has lost wireless communication with the
panel. Occasional display of this message may be
caused by local radio frequency interference.
If trouble persists,
call for service.
Orange Trouble LED
on the panel
The PC9155 has detected that an RF Jam condition has
been present for at least 20 seconds.
If trouble persists,
call for service.
,
,
,
,

7
Access Code Programming
In addition to the master code, you can program up to 16 additional user access codes. If wire-
less keys have been programmed then wireless key #1 will log as User Access Code #1 (if that
access code has been programmed). User Access Codes 1-16 will correspond to wireless keys
or prox tags 1-16. Press [Master Access Code]; the armed ( ) indicator will turn on.
Enter the 2-digit number to be programmed (e.g., 06 for User Access Code 6; enter 40 for the
master access code) or press the scroll buttons to find the specific code and press
to select. Enter the new 4-digit access code. When programming is complete, enter
another 2-digit code to program or press to exit. The access codes have programmable
attributes which allow zone bypassing, duress, supervisor, or one-time use activation.
On WT5500P keypads, you will be prompted to swipe a prox tag once the last character of the
access code is entered. To delete prox tags, the associated user access code must be deleted
as described, then re-programmed if required.
Access Codes [][5][Master Code] (when disarmed)
The [][5] User’s Programming command is used to program additional access codes.
User Codes - User codes 1-16 are available for the system.
Master Code (Access Code 40) - The master code has all of the attributes listed in the Pro-
grammable Attributes list below except for Duress (2) and One-Time Use (8) and is required to
program all supervisor code attributes.
Supervisor Codes - These codes are always valid when entering the User Code Pro-
gramming or User Function sections. However, these codes can only program addi-
tional codes which have equal or lesser attributes. Once programmed, the supervisor codes
receive the master code’s attributes. These attributes are changeable. Any user code can be
made a supervisor code by enabling User Code Attribute 1 (please see below for details).
Duress Codes - Duress codes are standard user codes that will transmit the Duress Alarm
Reporting Code whenever the code is entered to perform any function on the system. Any user
code can be made a duress code by enabling User Code Attribute 2 (see below for details).
One-Time Use Code - This code permits temporary access to the system for a 24-hour time
period. During the 24hr period, the temporary user may disarm the system once. There is no
restriction on the number of times the temporary user may arm the system during the time period.
NOTE: Duress codes are not valid when entering [][5], [][6] or [][8] sections.
NOTE: Access codes cannot be programmed as a duplicate or as a ’Code +/- 1’.
User Code Attributes
1. The default attributes of a new code will be the attributes of the code used to enter
whether it is a new code or an existing code being programmed.
2. System Master (Code 40) has Attribute 3 on by default.
NOTE: These attributes are not changeable.
Inherent Attributes (all codes except installer)
Arm / Disarm - Any access code will be valid for arming and disarming the system.
Command Outputs ([][7][1] and [][7][2]) - If these outputs require access code entry, any
access code is valid for performing the [][7][1-2][Access Code] functions on the system.
Programmable Attributes ([][5][Master/Supervisor Code][9][Code])
Zone Bypassing Attribute
This attribute allows the user to manually bypass zones if bypassing requires an access code.
Bell/Siren Squawk Attribute
This attribute is used to determine whether an access code should generate an arming/disarm-
ing squawk when the away function key is pressed on a wireless key fob. Contact your installer
1 Supervisor Code 4-6 For Future Use
2 Duress Code 7 Bell/Siren Squawk upon Away Arming/Disarming
3 Zone Bypassing Enabled 8 One-Time Use Code
,
,
,
,
,

8
to have this programmed. The Master code cannot use the Bell/Siren Squawk attribute, but the
code is required to enable the Bell/Siren for other codes.
NOTE: This feature cannot prevent the Arm/Disarming squawks from being generated if an
access code assigned to a wireless key is manually entered at a keypad.
Erasing an Access Code
To erase a code, select the code and enter as the first digit. If is entered, the system will
delete the code (including the associated prox tag) immediately and the user will be returned to
select another code.
Proximity Tag Enrollment (PT4/PT8)
Proximity (prox) tag readers are only available on WT5500P keypads. Refer to the label on top of
the keypad to confirm which model you have.
Enrolling Proximity Tags
1. Enter [][5][Master Code] to enter User Code Programming.
2. Scroll to the desired user code (01-16, or 40 for the master code) then press [].
3. Enter your desired 4 or 6-digit user access code. The following message will be displayed
after the user access code is entered:
Present Tag or
Press # to Exit
4. Place the prox tag near the tag reader ( ) at the left side of the display to assign it to the user
code. The following message will be displayed:
Tag Enrolled
Successfully
If an attempt is made to assign a prox tag to an existing user code that has an associated prox
tag, the following message will be displayed:
Duplicate
Tag/User Code
Return to Step 2 for instructions on how to enroll a user code.
NOTE: To exit the process at anytime, press [#].
Erasing a User Code/Proximity Tag
Enter [][5][Master Code], select the desired user code. Enter [] to erase the code and associ-
ated prox tag. The keypad will display the user number (e.g., 01) with a letter “P” if a user code
has already been programmed and a letter “T” if a code and prox tag have been programmed.
NOTE: User 40 for the master code cannot be deleted; an attempt to delete this user code will
delete the prox tag only. The prox tag must be re-enrolled before it can be used again.
Proximity Tag Operation
Place the prox tag near the tag reader ()at the left side of the display to arm/disarm your sys-
tem. When arming the system, the following message will be displayed:
Exit Delay in
Progress
When disarming the system, the following message will be displayed:
System Disarmed
If there is an attempt to swipe a prox tag that has not been enrolled, an error tone will sound and
the following message will be displayed:
Invalid Tag
Return to Step1 for instructions on how to enroll the prox tag.
WARNING: KEEP THE PROXIMITY TAG OUT OF REACH OF SMALL CHILDREN. THE MATERIALS ASSO-
CIATEDWITH THIS PRODUCT (LITHIUM BATTERIES,ETC.)MUSTBERECYCLEDACCORDINGTOLOCAL
RULES AND REGULATIONS.
,
,

9
User Function Commands
Disarm the system then enter [Master Code]. The command is used to gain
access to the following list of Master functions of the system:
[1] Time and Date - Enter 4 digits for 24hr System Time (HH-MM). Valid entries are 00-23 for the
hour and 00-59 for minutes. Enter 6 digits for the Month, Day and Year (MM-DD-YY).
[2]-[3] For Future Use.
[4] System Test - The system’s Siren Output - 4 seconds (2 seconds medium volume, 2 seconds
high volume), keypad lights, back-up battery pack and communicator are tested.
[5] Enable DLS / Allow Remote System Service - If enabled, the installer will be able to access
Installer Programming remotely using DLS (Downloading Software). This function provides a win-
dow for telephone ring detection by the alarm system. The DLS window will remain open for 6
hours, during which time the installer will be able to enter DLS an unlimited number of times. After
the 6-hr window has expired, access to programming via DLS will be unavailable until the window
is re-opened.
[6] User Call-up - If enabled by the installer, the panel will make 1 attempt to call the downloading
computer. The downloading computer must be waiting for the panel to call before downloading
can be performed.
[7] For Future Use.
[8] User Walk Test - Allows the user to enter the Walk Test mode. See Walk Test on page 12.
[9] Late to Open Enable/Disable - This function enables or disables the Late to Open time pro-
grammed in [0].
[0] Late to Open Time of Day - This function is used to program the time setting enabled in [9].
NOTE: Refer to ‘Late to Open’ section for details.
Changing Brightness/Contrast
When this option is selected, the keypad will allow you to scroll through 4 brightness levels and 10
contrast levels.
1. Press [Master Code].
2. Use the buttons to scroll to either Brightness Control or Contrast Control.
3. Press to select the setting you want to adjust.
4. a) Brightness Control: There are 4 backlighting levels. Use the buttons to scroll to the
desired level.
b) Contrast Control: There are 10 different display contrast levels. Use the buttons to
scroll to the desired contrast level.
5. To exit, press .
Ambient Light Sensor
During battery operation, the keypad uses the ambient light sensor ( ) to automatically adjust
the backlighting brightness levels to conserve battery life.
Changing the Buzzer Level
When this option is selected, the keypad will allow you to scroll through 21 different buzzer levels.
A level of 00 disables the buzzer.
1. Press [Master Code].
2. Use the buttons to scroll to Buzzer Control, then press to select.
3. There are 21 levels; use the buttons to scroll to the desired level. Press to exit.
Viewing the Event Buffer
The event buffer will show you a list of the last 500 events that have occurred on your system.
1. Press [Master Code].
2. To select Event Buffer viewing, press .
3. The keypad will display the event number and the time and date. Press to switch
between this information and the event details.
4. Use the buttons to scroll through the events in the buffer.
5. To exit event buffer viewing, press .
,
,
,
,
,
,
,
,
,

10
Late to Open
This features allows a user to be notified if their alarm system is not disarmed by a programmed
time of day.
NOTE: The Late to Open feature requires the monitoring station to forward calls to the user. Verify
with the installer whether this function is active.
[9] Late to Open Enable/Disable
This
Late to Open feature enables or disables the Late to Open time programmed in [0].
It is typically used to track children after school. For example, if the parents get home from work
at 5pm, and a child gets home at 4pm. The programmable timer could be set for 4:15. If the
system is not disarmed at this time an alert would be sent to the monitoring station.
The keypad will display ’Late to Open is Enabled’ and sound 3 beeps if is pressed within
the User Functions menu when this feature is off. The LCD keypad will display ’Late to Open is
Disabled’ and sound an error tone if is pressed within the User Functions menu when this
feature is on.
[0] Late to Open Time of Day
This function is used to program the time setting enabled in [9]. This function programs the
’Late to Open’ time of day for all 7 days of the week.
• Valid entries for these sections are 00:00 – 23:59.
• Entering 99:99 will disable the Late to Open feature for the current day.
• After entering [Master Code] , beeps will be sounded and ’Press () for < > Sun-
day’ will be displayed on the keypad.
• Pressing the right scroll button displays the days of the week, from Sunday to Saturday.
While in the Late to Open menu, entering keys 1-7 will also select each day from Sunday to
Saturday, respectively.
•If is pressed to select a day of the week, no beeps will be sounded and the keypad will
display ’Set 24hr Time’ ’Enter HH:MM 9999’. If is pressed from this menu, the user will
be returned to the previous Late to Open menu.
• If the Alarm System is armed in any mode when the late to open time matches the time of day,
Late to Open will be logged to the event buffer and communicated to the monitoring station.
Two-Way Wireless Key (WT4989, WT8989)
The Two-way Wireless Key communicates directly with the control panel, performing many of the
functions that a wireless keypad performs. Please refer to the WT4989/8989 Operating instruc-
tions for more information.
The WT4989 and WT8989 has 4 function keys programmable for 6 functions each, an LCD icon
display that can display system status using a combination of 7 icons and an internal buzzer.
Unless custom programmed by your installer the functions are as follows:
Function Keys
Status Request - Press this button for 1 second to view the control panel system
status via the LCD display icons.
Stay Arming - Press to arm your system in Stay mode. All perimeter zones are active
but interior zones remain inactive.
Away Arming - Press to arm your system. Interior and exterior zones will be armed.
Disarm - Press to disarm your system.
Panic Alarm - Press & hold for 3 seconds to create a panic alarm on the security system.
* Command Output 1 - Press & hold both buttons at the same time for 3 seconds to
activate the assigned output.
*
Command Output 2 - Press & hold both buttons at the same time for 3 seconds to
activate the assigned output.
,
,

11
WT4989/WT8989 Status Display Icons
The table below summarizes the status that can be shown by the WT4989/WT8989 LCD:
Buzzer
Provides an audible confirmation of a pressed button or that a command to the panel has been executed.
Keylock Mode
Ensures that the system is not accidently armed or disarmed by the wireless key.
To lock the keys:
1. Press and hold the Status and Away keys simultaneously for 3 seconds.
2. After 3 seconds, the wireless key will beep and flash the keylock icon ( ) to indicate that the
keys are locked.
To unlock the keys:
1. Press and hold the Status and Away keys simultaneously for 3 seconds.
NOTE: Pressing the panic key for 3 seconds will also exit Keylock mode.
2. Upon exiting Keylock mode, the status will be automatically displayed.
Testing Your System
NOTE: Inform your Monitoring Station when you begin and end system testing.
All smoke detectors in this installation must be tested by your smoke detector installer or dealer
once a year to ensure they are functioning correctly. It is the user’s responsibility to test the system
weekly (excluding smoke detectors). Ensure you follow all the steps in the two tests below.
NOTE: Should the system fail to function properly, call your installer immediately for service .
Siren and Keypad Display Test
This test activates all display pixels and indicator lights on the keypad and does a 4-second
check of the siren.
1. Press [Master Code] .
The following will occur:
- The system activates the siren output on medium volume for 2 seconds followed by full vol-
ume alarm for 2 seconds. All display lights and LCD pixels will turn on.
- The Ready, Armed, Trouble and Power LED’s will flash for the duration of the test.
2. To exit the function menu, press .
Keypad Low Battery
The flashing trouble icon on a keypad will indi-
cate that keypad has a low battery.
Keypad Battery Replacement
1. Slide the keypad up and out from the mounting
plate/desk stand (removing the screws first if
required). The bay for the four AA batteries is open
and visible at the back of the keypad.
2. Insert the batteries as directed on the back of the
keypad. Ensure the correct polarity is observed.
3. Slide the keypad back onto the mounting plate /
desk stand.
ICON (S=Steady, F=Flashing)
(S) System Trouble (S) Alarm in Memory
(F) Keylock Enable (F) Active Alarm
(S) Disarmed (F) [][9] Armed - Away
(S) Away - Armed (F) [][9] Armed - Stay
(S) Stay - Armed (F) [][9] Armed - Night
(S) Night - Armed (S) Low Battery
(F) Critical Low Battery
,
$$ $$
$$
$$
DG009048
Mounting
Holes
Mounting
Holes
Batteries
Plug
Wire
Channel
Tamper
Switch

12
WT4901/WT8901 Siren Battery Test
To determine which siren has a low battery press and hold the test button, located at the front of
the siren, for 5 seconds.
• If the siren sounds for 4 seconds, the batteries are good.
• If the siren doesn’t sound, the batteries are low.
WT4901/WT8901 Siren Battery Replacement
• Open the front cover and remove old batteries. Once the old batteries are removed, wait 30
seconds before inserting the replacement batteries.
Note: Only use Energizer 1.5V AA alkaline batteries.
•I nstall new batteries as shown in the polarity indicated by the engraving. If the batteries are
installed incorrectly, in the reverse polarity, the indoor siren will not work. With typical use, the
WT4901/WT8901 batteries should be replaced every two years.
DO NOT TRY TO RECHARGE THESE BATTERIES. DISPOSAL OF USED BATTERIES MUST BE MADE
IN ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
Walk Test
Walk Test mode allows you to test the operation of each detector in the system. While in Walk Test
mode, the Ready, Armed, and Trouble LED's will flash to indicate that the Walk Test is active. The
Walk Test can be terminated at anytime by re-entering [Master Code] on the keypad.
The system will also automatically terminate the Walk Test on completion; it will sound an audible
warning (5 beeps every 10 seconds), beginning 5 minutes before the termination of the test.
1. Before testing, ensure that the system is disarmed and the Ready light is on.
2. Press and close all zones to return the system to the Ready state.
3. Perform a System Test by following the steps in the previous section.
4. Press [Master Code] to initiate the Walk Test.
5. To test the zones, activate each detector in turn (e.g., open each door/window or walk in
motion detector areas).
The System will display the following message when each zone (detector) is activated: ‘Secure
System Before Arming < >’, or ‘Secure or Arm System’. Use the buttons to view which
zones are open. The message will disappear when the zones are closed.
Allowing Computer Access to your System
Occasionally, your installer may need to send information to or retrieve information from your
security system. Your installer will do this by having a computer call your system. You may need
to prepare your system to receive this ‘downloading’ call. To do this:
Press [Master Code] at the keypad. This allows downloading for a limited period
of time. During this time, the system will answer incoming downloading calls. For more informa-
tion on this feature, please ask your installer.
Reference Sheets
Fill out the following information for future reference and store this guide in a safe place.
System Information
Enabled?
 FIRE  AUXILIARY  PANIC
For Service
Central Station Information:
Account#: ___________________ Telephone#: __________________
Installer Information:
Company: ___________________ Telephone#: __________________
,
,
,
The Entry Delay Time is _______ seconds.
The Exit Delay Time is _______ seconds.

13
If you suspect a false alarm signal has been sent to the central monitoring station,
call the station to avoid an unnecessary response.
Access Codes
Master Code [40]: ______________________ Proximity Tag: 
Sensor / Zone Information
Code Wireless
Key
Prox
Tag Access Code Code Wireless Key
Prox
Tag Access Code
01  09 
02  10 
03  11 
04  12 
05  13 
06  14 
07  15 
08 16 
Sensor Protected Area Sensor Type Sensor Protected Area Sensor Type
01 18
02 19
03 20
04 21
05 22
06 23
07 24
08 25
09 26
10 27
11 28
12 29
13 30
14 31
15 32
16 33
17 34

14
Keypad Quick Guide
Status Lights
Ready - must be on to arm system. All zones must be secured or bypassed and the
system disarmed for this light to activate.
Armed - indicates system is armed. If the Ready light and the Armed light are both on
it indicates an Exit Delay is in progress.
Trouble - On indicates a system malfunction or tamper. Flashing - Indicates that the
keypad has a low battery condition. Follow the instructions displayed or enter
to view trouble. The Trouble light will turn off when the trouble is corrected.
AC Power - indicates AC Power is present. The AC Power light will turn off when AC is
absent.
Function Keys
Stay Arms the system in Stay Mode.
Away Arms the system in Away Mode.
Chime Same as pressing on the keypad.
Bypass Same as pressing on the keypad.
Quick Exit Same as pressing on the keypad.
Special Keys
Language Selection - Press and hold both buttons simultaneously for 2 seconds to acti-
vate. Scroll to the desired language. Press to select choice.
Fire - Press and hold for 2 seconds to activate. These keys must be
programmed by the
installer to function.
Auxiliary - Press and hold for 2 seconds to activate.
Panic - Press and hold for 2 seconds to activate.
User Commands
Press to select, press to scroll, press to exit.
PRESS... To ...
Bypass Zones
Press Clear Bypass
Press Bypass Recall
Press Save Bypass
Press Recall Save
View System Troubles Scroll to view all troubles
View Alarms in Memory Scroll to view alarms
Chime ON/OFF Turns chime on and off
,
,
,
,
,
,
,
,
,
,

15
Guidelines for Locating Smoke & CO Detectors
The following information is for general guidance only and it is recommended that local fire codes
and regulations be consulted when locating and installing smoke alarms and CO Alarms:
Smoke Detectors
Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent.
Experiments with typical fires in homes indicate that detectable quantities of smoke precede de-
tectable levels of heat in most cases. For these reasons, smoke alarms should be installed out-
side of each sleeping area and on each storey of the home.
The following information is for general guidance only and it is recommended that local fire codes
and regulations be consulted when locating and installing smoke alarms.
It is recommended that additional smoke alarms beyond those required for minimum protection
be installed. Additional areas that should be protected include: the basement; bedrooms, espe-
cially where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not pro-
tected by the required units.
On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing
may be required depending on ceiling height, air movement, the presence of joists, uninsulated
ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULC-S553-02 or other appropriate
national standards for installation recommendations.
• Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in
these locations may prevent the unit from detecting smoke.
• Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement
around the detector may prevent smoke from entering the unit.
• Do not locate detectors in areas of high humidity.
• Do not locate detectors in areas where the temperature rises above 38oC(100oF) or falls below
5oC (41oF).
Program User Codes
Change Attributes
Press buttons to scroll to user code. Enter
[Master Code][9][xx] to enter the user code (xx = 1-16).
[1] Supervisor’s Code
[2] Duress Code
[3] Zone Bypassing
[4]-[6] Future Use
[7] Bell/Siren Squawk Output
[8] One Time Use Code
User Commands
User Options Event Buffer
System Test
Time and Date
System Service/DLS
User Call-up
Walk Test
Brightness Control
Buzzer Level Control
Contrast Control
Late to Open
PGM Commands If programmed by the installer, can be used to activate
events such as opening/closing garage doors.
Installer Programming Requires Special Code.
No-Entry Arming The system will arm in Stay mode after the exit delay
expires, the entry delay is disabled.
Quick Arm/Quick Exit Quick Arm is equivalent to entering your user code.
Quick Exit allows you to exit the premises without disarming
the system.
,
,
,
,
,
,

16
Smoke detectors should always be installed in USA in accordance with Chapter 11 of NFPA 72,
the National Fire Alarm Code: 11.5.1.1 Where required by applicable laws, codes, or standards
for a specific type of occupancy, approved single- and multiple-station smoke alarms shall be
installed as follows:
(1) In all sleeping rooms and guest rooms.
(2) Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft) of any door to a
sleeping room, the distance measured along a path of travel.
(3) On every level of a dwelling unit, including basements.
(4) On every level of a residential board and care occupancy (small facility), including base-
ments and excluding crawl spaces and unfinished attics.
(5) In the living area(s) of a guest suite.
(6) In the living area(s) of a residential board and care occupancy (small facility).
Carbon Monoxide Detectors
Carbon monoxide is colorless, odorless, tasteless, and very
toxic. Carbon monoxide gas moves freely in the air. Suggest-
ed locations are in or as near as possible to sleeping areas of
the home. The human body is most vulnerable to the effects
of CO gas during sleeping hours. For maximum protection, a
CO alarm should be located outside primary sleeping areas
or on each level of your home. Figure 5 indicates the suggest-
ed locations in the home. The electronic sensor detects car-
bon monoxide, measures the concentration and sounds a
loud alarm before a potentially harmful level is reached.
Do NOT place the CO alarm in the following areas:
• Where the temperature may drop below -10ºC or exceed 40ºC
• Near paint thinner fumes
• Within 5 feet (1.5 meter) of open flame appliances such as furnaces, stoves and fireplaces
• In exhaust streams from gas engines, vents, flues or chimneys
• Do not place in close proximity to an automobile exhaust pipe; this will damage the detector
WARNING: PLEASE REFER TO THE CO DETECTOR INSTALLATION AND OPERATING IN-
STRUCTION SHEET FOR EMERGENCY INFORMATION.
Figure 1
Figure 2
Figure 3a
Figure 4
Figure 3
GROUN D
FLOOR
BASEMENT
KITC HEN GARAGE
BEDROOM
BEDROOM
BEDROOM
CARBON MONO XI DE DE TEC TOR
Figure 5