EDM Solution 6+6 Wireless-AE User manual

Solution 6+6 Wireless - AE
Installation Manual
ISSUE 1.20

This page has been included for you to cut out and insert into the spine
of the folder
MA660I
S
olution
6+6
Wireless
AE
Installation
Manual
(61-2) 9672 1233
ISSUE 1.20

Solution 6+6 Wireless - AE
Installation Manual
Copyright 1997 by Electronics Design and Manufacturing Pty Limited,
SYDNEY, AUSTRALIA
Document Part Number MA660I
Document ISSUE 1.20
Printed 02 July 2001
This documentation is provided to suit Solution 6+6 Wireless - AE (CC660/LP660)
Firmware Revision 1.00 – 1.02
Hardware Revision A
Alarm Link Form - Software Version 1.00 = CRO1V10
Copyright Notice
All rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrieval system in any form or
by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of
Electronics Design and Manufacturing Pty Limited.
Trademarks
Throughout this document trademark names may have been used. Rather than put a trademark symbol in every occurrence
of a trademark name, we state that we are using the names only in an editorial fashion and to the benefit of the trademark
owner with no intention of infringement of the trademark.
Notice of Liability
While every precaution has been taken in the preparation of this document, neither Electronics Design and Manufacturing
Pty Limited nor any of its official representatives shall have any liability to any person or entity with respect to any
liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this book.
Electronics Design and Manufacturing Pty Limited reserves the right to make changes to features and specifications at any
time without prior notification in the interest of ongoing product development and improvement.

Table Of Contents
Introduction_____________________________________________________________________ 15
Introduction__________________________________________________________________________ 16
Features _____________________________________________________________________________ 17
Quick Start___________________________________________________________________________ 18
Zone Defaults ________________________________________________________________________________ 18
Programming____________________________________________________________________ 19
Programming_________________________________________________________________________ 20
Programming With The Remote Codepad_________________________________________________ 21
Programming With The Hand Held Programmer___________________________________________ 22
Programming With The Programming Key________________________________________________ 23
Programming Option Bits ______________________________________________________________ 23
Installer’s Programming Commands _____________________________________________________ 24
Command 958 - Enable/Disable Zone Status Mode ___________________________________________________ 25
Command 959 - Test Programming Key ___________________________________________________________ 26
Command 960 - Exit Installer's Programming Mode __________________________________________________ 26
Command 961 - Reset Control Panel Back To Factory Default Settings ___________________________________ 27
Command 962 - Copy Control Panel Memory To Programming Key _____________________________________ 27
Command 963 - Copy From Programming Key To Control Panel________________________________________ 28
Command 964 - Erase Programming Key __________________________________________________________ 29
Command 965 - Set Up Domestic Dialling Format ___________________________________________________ 30
Command 966 - Enable/Disable Automatic Stepping Of Locations_______________________________________ 31
Command 999 - Display Software Version Number __________________________________________________ 32
Disable Factory Default ________________________________________________________________________32
Defaulting The Control Panel ____________________________________________________________________ 33
System Indicators and Operations ___________________________________________________ 35
System Indicators and Operations________________________________________________________ 36
CP5 Eight Zone Codepad_______________________________________________________________ 36
Zone Indicators _______________________________________________________________________________ 36
AWAY Indicator______________________________________________________________________________ 36
STAY Indicator_______________________________________________________________________________ 36
MAINS Indicator _____________________________________________________________________________ 37
FAULT Indicator _____________________________________________________________________________ 37
Audible Indicators_____________________________________________________________________________ 37
CP5 Eight Zone LCD Codepad __________________________________________________________ 38
Zone Indicators _______________________________________________________________________________ 38
AWAY Indicator______________________________________________________________________________ 38
STAY Indicator_______________________________________________________________________________ 38
System Disarmed _____________________________________________________________________________ 39
MAINS Indicator _____________________________________________________________________________ 39
Zone Isolating Mode ___________________________________________________________________________ 39
FAULT Indicator _____________________________________________________________________________ 39
Programming Mode ___________________________________________________________________________ 39
Off Indicator/Zone Sealed_______________________________________________________________________40
On Indicator/Zone In Alarm _____________________________________________________________________ 40
Audible Indicators_____________________________________________________________________________ 40
System Operations_____________________________________________________________________ 41
Arming The System In AWAY Mode _____________________________________________________________ 41
Forced Arming _____________________________________________________________________________ 41
Disarming The System From AWAY Mode_________________________________________________________ 41
Arming The System In STAY Mode ______________________________________________________________ 42
Forced Arming _____________________________________________________________________________ 42
Disarming The System From STAY Mode__________________________________________________________ 43

Codepad Duress Alarm_________________________________________________________________________ 44
Codepad Panic Alarm__________________________________________________________________________ 44
Codepad Fire Alarm ___________________________________________________________________________ 44
Codepad Medical Alarm________________________________________________________________________ 44
Isolating Zones ________________________________________________________________________45
Standard Isolating_____________________________________________________________________________ 45
Code To Isolate_______________________________________________________________________________ 46
Fault Analysis Mode____________________________________________________________________47
Fault Descriptions_____________________________________________________________________________ 48
Low Battery _______________________________________________________________________________ 48
Date and Time______________________________________________________________________________ 48
Sensor Watch ______________________________________________________________________________ 48
Horn Speaker Monitor _______________________________________________________________________ 48
Reserved __________________________________________________________________________________ 48
E2Fault ___________________________________________________________________________________ 48
Zone Transmitter Low Battery _________________________________________________________________ 48
Communication Failure ______________________________________________________________________ 49
AC Mains Failure ___________________________________________________________________________ 49
System Functions_________________________________________________________________ 51
System Functions ______________________________________________________________________52
Installer Code Functions ________________________________________________________________52
Fault Analysis Mode_________________________________________________________________________ 53
How To Enter Fault Analysis Mode_____________________________________________________________ 53
Enable/Disable Wireless Zones ________________________________________________________________ 54
Set The Number Of Days Until The First Test Report_______________________________________________ 55
Event Memory Recall Mode___________________________________________________________________ 56
Walk Test Mode ____________________________________________________________________________ 57
Satellite Siren Service Mode___________________________________________________________________ 57
Initiate Modem Call _________________________________________________________________________ 57
How To Initiate A Modem Call ________________________________________________________________ 57
Turning Telephone Monitor Mode On/Off________________________________________________________ 58
Reserved __________________________________________________________________________________ 58
Send Test Report____________________________________________________________________________ 58
Master Code Functions _________________________________________________________________59
Arm Or Disarm Both Areas At The Same Time____________________________________________________ 59
Changing and Deleting User Codes _____________________________________________________________ 60
Changing and Deleting Remote Radio User Codes _________________________________________________ 62
Changing Domestic Phone Numbers ____________________________________________________________ 64
Event Memory Recall Mode___________________________________________________________________ 65
Walk Test Mode ____________________________________________________________________________ 66
Fault Analysis Mode_________________________________________________________________________ 67
Setting The Date and Time____________________________________________________________________ 68
Turn Day Alarm On and Off___________________________________________________________________ 68
Reset Latching Outputs_______________________________________________________________________ 69
Initiate Modem Call _________________________________________________________________________ 69
User Code Functions – Partitioned Systems Only____________________________________________70
Arm Or Disarm Both Areas At The Same Time____________________________________________________ 70
Hold Down Functions___________________________________________________________________71
Arm The System In AWAY Mode______________________________________________________________ 71
Arm The System In STAY Mode_______________________________________________________________ 71
Horn Speaker Test __________________________________________________________________________ 71
Bell Test __________________________________________________________________________________ 71
Strobe Test ________________________________________________________________________________ 72
Turning Day Alarm On and Off ________________________________________________________________ 72
Fault Analysis Mode_________________________________________________________________________ 72
Initiate A Modem Call _______________________________________________________________________ 73
Reset Latching Outputs_______________________________________________________________________ 73
Codepad ID & Beeper Tone Change ____________________________________________________________ 73
Initiate A Test Report ________________________________________________________________________ 73

Remote Operations _______________________________________________________________ 75
Remote Operations ____________________________________________________________________ 76
Remote Radio Transmitter Operation ____________________________________________________ 76
Arming Via Transmitter In AWAY Mode ________________________________________________________ 76
Disarming Via Transmitter From AWAY Mode ___________________________________________________ 76
Arming Via Transmitter In STAY Mode _________________________________________________________ 77
Disarming Via Transmitter From STAY Mode ____________________________________________________ 77
Panic Alarm Via Transmitter __________________________________________________________________ 77
Turning An Output On Via Transmitter __________________________________________________________ 77
Turning An Output Off Via Transmitter__________________________________________________________ 77
Remote Arming Via The Telephone ______________________________________________________ 78
Upload/Download Via Alarm Link Software _______________________________________________ 79
Remote Connect ______________________________________________________________________________ 79
Remote Connect With Customer Control _________________________________________________________ 79
Remote Connect Without Call Back Verification___________________________________________________ 79
Remote Connect With Call Back Verification _____________________________________________________ 80
Dialler Reporting Formats _________________________________________________________ 81
Dialler Reporting Formats ______________________________________________________________ 82
Contact ID Format ____________________________________________________________________________ 82
Point ID Codes _______________________________________________________________________________ 83
Securitel ____________________________________________________________________________________ 84
Domestic Reporting Format _____________________________________________________________________ 85
Domestic Dialling Function ___________________________________________________________________ 85
Acknowledge Domestic Dialling _________________________________________________________________ 85
Programming Domestic Reporting ______________________________________________________________ 86
Disable Domestic Dialling ______________________________________________________________________ 87
Basic Pager Reporting Format ___________________________________________________________________ 88
Base Station Information __________________________________________________________ 89
Base Station Information _______________________________________________________________ 90
Primary Telephone Number _____________________________________________________________________ 91
Secondary Telephone Number ___________________________________________________________________ 91
Call Back Telephone Number____________________________________________________________________ 91
Dialling Format_______________________________________________________________________________ 92
Handshake Tone ______________________________________________________________________________ 92
Transmission Format___________________________________________________________________________ 93
Reserved ____________________________________________________________________________________ 93
Subscriber ID Number _________________________________________________________________________ 93
Ring Count __________________________________________________________________________________ 94
Answering Machine Bypass _____________________________________________________________________ 94
User Codes______________________________________________________________________ 95
Access Codes _________________________________________________________________________ 96
Installer Code ________________________________________________________________________________ 96
User Codes __________________________________________________________________________________ 96
Remote Radio User Codes ______________________________________________________________________ 96
Teaching Radio User Codes ___________________________________________________________________ 96
Default User Codes ____________________________________________________________________________ 97
User Code Priority ____________________________________________________________________________ 98
Arm and Disarm ____________________________________________________________________________ 98
Arm Only _________________________________________________________________________________ 98
Patrolman Code_____________________________________________________________________________ 98
Arm and Disarm + Code To Isolate _____________________________________________________________ 98
Patrolman Code + Code To Isolate______________________________________________________________ 98
Arm and Disarm + Master Code Functions________________________________________________________ 98
Arm and Disarm + Master Code Functions + Code To Isolate_________________________________________ 98
Code Retries _________________________________________________________________________________ 99

Zone Information________________________________________________________________ 101
Zone Information _____________________________________________________________________102
Day Alarm Mask ____________________________________________________________________________ 102
Day Alarm Resetting _______________________________________________________________________ 102
Day Alarm Latching________________________________________________________________________ 102
Day Alarm Operation _________________________________________________________________________ 103
Day Alarm When Partitioned _________________________________________________________________ 103
EOL Resistor Value __________________________________________________________________________ 104
Connections Of Split EOL Resistors Using N/O Contacts_____________________________________________ 105
Zone Programming ___________________________________________________________________106
Zone Operating Information__________________________________________________________________ 106
Zone Reporting Options _____________________________________________________________________ 106
Tamper Zones_______________________________________________________________________________ 107
Zone Defaults _______________________________________________________________________________ 108
Zone Types_________________________________________________________________________________ 108
Instant Zone ______________________________________________________________________________ 108
Handover Zone____________________________________________________________________________ 108
Delay-1 Zone _____________________________________________________________________________ 108
Delay-2 Zone _____________________________________________________________________________ 108
Reserved _________________________________________________________________________________ 108
Reserved _________________________________________________________________________________ 109
Instant Zone + Isolated In STAY Mode _________________________________________________________ 109
Handover Zone + Isolated In STAY Mode_______________________________________________________ 109
Delay-1 Zone + Isolated In STAY Mode ________________________________________________________ 109
Delay-2 + Isolated In STAY Mode_____________________________________________________________ 109
Reserved _________________________________________________________________________________ 109
Keyswitch Zone ___________________________________________________________________________ 109
24 Hour Burglary Zone______________________________________________________________________ 109
24 Hour Fire Zone _________________________________________________________________________ 109
Chime Zone ______________________________________________________________________________ 109
Zone Not Used ____________________________________________________________________________ 109
Zone Options _______________________________________________________________________________ 110
Lockout Siren & Lockout Dialler______________________________________________________________ 110
Silent Alarm ______________________________________________________________________________ 111
Sensor Watch _____________________________________________________________________________ 111
Keyswitch Zone Options ______________________________________________________________________ 112
Latching Arm and Disarm In AWAY Mode _____________________________________________________ 112
Latching Arm In AWAY Mode _______________________________________________________________ 112
Latching Disarm From AWAY Mode Or STAY Mode _____________________________________________ 112
Latching Arm and Disarm In STAY Mode ______________________________________________________ 112
Latching Arm In STAY Mode ________________________________________________________________ 112
Latching Disarm From AWAY Mode Or STAY Mode _____________________________________________ 112
Momentary Arm and Disarm In AWAY Mode ___________________________________________________ 113
Momentary Arm In AWAY Mode _____________________________________________________________ 113
Momentary Disarm From AWAY Mode Or STAY Mode___________________________________________ 113
Momentary Arm and Disarm In STAY Mode ____________________________________________________ 113
Momentary Arm In STAY Mode ______________________________________________________________ 113
Momentary Disarm From AWAY Mode Or STAY Mode___________________________________________ 113
Zone Pulse Count ____________________________________________________________________________ 114
Zone Pulse Count Handover__________________________________________________________________ 114
Zone Pulse Count Time _______________________________________________________________________ 114
Reporting Options _______________________________________________________________ 115
Reporting Options ____________________________________________________________________116
Report Options 1_____________________________________________________________________________ 116
Enable Zone Bypass Reports _________________________________________________________________ 116
Enable Zone Bypass Restore Reports___________________________________________________________ 116
Enable Zone Trouble Reports_________________________________________________________________ 116
Enable Zone Trouble Restore Report ___________________________________________________________ 116
Report Options 2_____________________________________________________________________________ 117
Enable Duress Reports ______________________________________________________________________ 117
Enable Panic, Medical & Fire Reports __________________________________________________________ 117
Enable Access Denied Reports________________________________________________________________ 117