Alfaled AFR-6 User manual

●Apply to single color LED controller, dimming driver or smart lamp.
Ultra sensitive color adjustment touch w heel.●
●Each remote can match one or more receiver.
● R bC 2032 attery pow ered.
●Operate w ith LED indicator light.
User Manual Ver 1.0.3 www.alfaled.sk
Technical Parameters
Input and Output
W arranty
5 years
W arranty
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Ta: -30
O
C ~+55
O
C
Tc: +85
O
C
Model No.: AFR-6 / AFR-6-1
Features
Touch w heel/ W ireless remote 30m distance/ CR20 3 2 battery
Ultrathin Touch W heel RF Remote Controller
AFR-6 AFR-6-1
Output signal RF 2.4GHz( )
W orking voltage 3VDC CR2032( )
W orking current ＜5mA
Standby current ＜10μA
Standby time 1 year
Remote distance 30 m
S afety a nd E M C
EMC standard (EMC) EN301 489,EN 62479
Radio Equipment(RED) EN300 328
Certification CE,EMC,LVD,RED
EN60950
Safety standard(LVD)
LVD
Page 1

User Manual Ver 1.0.3 www.alfaled.sk Page 2
Dimension
9mm
58.5mm
107mm
58.5mm
Operation
●Pull out the plastic battery barrier sheet from the battery compartment located on the bottom of the remote.
●To ex tend battery life, no touch or press key operation after a few seconds,
the touch w heel w ill enter sleep state, y ou need press any key to make touch w heel quit sleep state.
Match Remote Control (two match w ays)
Use the controller’s Match key
Match:
Short press match key, immediately press on/ off
key (single zone remote) or zone key (multiple zone
remote) of the remote.
Use Pow er Restart
Match:
Switch off the power, then switch on power again,
immediately short press on/ off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
.
Delete:
Switch off the power, then switch on power again,
immediately short press on/ off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
Delete:
Press and hold match key for 5s to delete all match,
The light blinks 5 times means all matched remotes
were deleted.
End user can choose the suitable match/ delete w ay s. Tw o options are offered for selection:
AFR-6, AFR-6-1 Ultrathin Touch Wheel RF Remote Controller

User Manual Ver 1.0.3 www.alfaled.sk Page 3
AFR-6, AFR-6-1 Ultrathin Touch Wheel RF Remote Controller
AFR-6 4 zone dimming remote
On/ Off: Short press turn on/ off all z one light.
1,2,3,4 z one:S hort press select and turn on z one light, long press 2 s turn off z one light.
Short press multiple z one key fastly, w ill sy nchronous select multiple z one synchronously.
Bright w heel: Touch to change current z one brightness.
Bright+/ -:Adjust brightness for current selected z one,
short press 1 0 levels,long press 1-5s for continuous 2 5 6 levels adjustment.
3 Scene: Short press recall the scene,long press 2s save the current state into the scene.
4 z one recall or save sy nchronously.
10 0%
1%
50%
Bright-
3 Scene
4 Zone
Bright w heel
On/ Off
Bright+
N ote: The remote AFR-6 can be used as 4 zone dimming remote or single zone 4 channel dimming remote.
Operation: Long press " " +" " at the same time for 2 seconds as 4 channel dimming remote,
only match w ith one or multiple receiver of 4 channel, such as V4,VP,V4-L or C4 controller.
Operation: Long Press " " +" " key at the same time as 4 z one dimming remote,
each z one match w ith one or multiple receivers.
W hen set ok, the red indicator w ill light on longer.

User Manual Ver 1.0.3 www.alfaled.sk Page 4
AFR-6, AFR-6-1 Ultrathin Touch Wheel RF Remote Controller
AFR-6-1 1 zone dimming remote
On/ Off: Turn on/ off light.
Bright w heel: Touch to change brightness.
Bright+/ -:Adjust brightness, short press 10 levels,long press 1-5s for continuous 256 levels adjustment.
100%,75%,50%,25%: Get 4 kinds brightness directly.
3 Scene: Brightness memory. Short press recall the scene,long press 2s save the current brightness into the scene.

Bright-
3 Scene
Bright wheel
Bright+
4 Bright
On/ Off
S afety informa tion
1.Read all instructions carefully before y ou begin this installation.
2.W hen installing battery, pay attention to the battery positive and negative polarity.
A long time w ithout the remote control, remove the battery.
W hen remote distance becomes smaller and insensitive, replace the battery.
3. If no response from the receiver, please re-match the remote.
4.Gently handle remote, bew are of falling.
5. For indoor and dry location use only.