ALFAtron ALF-10XU2-CAM User manual

www.alfatronelectronics.com
ALFATRON ELECTRONICS GmbH GERMANY
ALF-10XU2-CAM
Full HD USB2.0 PTZ Camera
All Rights Reserved

Alfatron ALF-10XU2-CAM
1
Safety Precaution
To ensure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
This product must be installed by a professional technician and cannot be
dismantled.
Do not expose the unit to rain, moisture or install this product near liquid.
Only use a soft and dry cloth for cleaning. Do not use any strong corrosive cleaning
materials as it will damage the housing and lens.
Introduction
Alfatron ALF-10XU2-Cam is an HD PTZ camera equipped with 1080p with a 10x Zoom
lens. This PTZ camera is suitable for medium to large size meeting rooms,
boardrooms, and conference venues.
ALFAtron ALF-10XU2-Cam is compatible with video meeting software such as Skype
and Zoom. The 1080P HD PTZ camera is equipped for a high-quality video stream and
high definition real-time synchronization
Features
Full HD (1920x1080p)
Field of view 60.9° (Wide) – 6.43° (Tele)
Pan 355° - Tilt 120°
USB2.0
RS232C and RS 422C Control
PC Control with Sony VISCA or Pelco P/D commands
Multi-function IR remote control
Package List
1 x PTZ Camera 1 x Power Adaptor and cable

1 x Remote Control

1 x Bracket

1 x USB Cable

1 x User Manual
Note: If you find any defective or missing parts, please contact your local dealer.

Alfatron ALF-10XU2-CAM
2
Camera Description
Front Panel
1. Lens.
2. IR Sensor for the remote control.
3. Power indicator.
4. Standby indicator.
Rear Panel
5. IR Sensor for the remote control.
6. IR Select Switch.
7. RS-422C/485 VISCA / PELCO.
8. 12V DC input.
9. VISCA RS-232C IN Connector.
10. USB 2.0.
11. Screw hole.
12. VISCA RS-422/RS-232C Bottom Switch.

Alfatron ALF-10XU2-CAM
3
Remote Controller
Control Port Diagram
1. Camera Select.
2. Focus: Auto or Manual
3. M-Open: open the menu.
4. Back Light.
5. Power.
6. STD REV: (Press L/R Direction Set, and
then Press 1 or 2)
7. Position: Number Area: Preset: Press
Preset then 1-9 for setup preset position
8. Reset: Press Reset and then press 1-9 to
reset preset position
9. Zoom.
10. Pan – Tilt Reset.
11. Pan – Tilt: Home – Middle position.
12. L / R Direction Set.
13. IR Transmit.
14. Close Menu.
15. S- Out: Switch to 720P50.
16. Data-Screen: Switching Color mode.

Alfatron ALF-10XU2-CAM
4

Alfatron ALF-10XU2-CAM
5
Remote Commander Operation
A: Pan / Tilt Control
1: Power On, Pan /Tilt will be in initial position
2: Press the arrow to adjust the position while
watching the video image, you can move
direction by using the arrow keys step by
step. To set the position press (up or down)
and arrow (Left or right) at the same time.
3: Press Home to go back to front facing
position.
4: Press PAN-TILT RESET or turn off power
and then on again to reset the position of the
camera.
5: Press L/R Direction set and STD or REV at
the same time, with the right or left arrow to
turn the cameras position.
B: Adjust the camera
1: Focus
1.1: Auto: Press Auto for to automatically set
the focus.
1.2: Manual: Press MANUAL and then Far or
Near to adjust.
2: Zoom – Press T or W for far or near zoom.

Alfatron ALF-10XU2-CAM
6
One remote to control multiple cameras
1: A maximum of three cameras can be controlled by one
remote control.
2: Press CAMERA SELECT 1 or 2 or 3 to select the
camera you want to control. The button will light up once
selected.
Backlight Compensation
1: If there is too much light behind the object, the
object will appear black. You can adjust this by
pressing the BACK LIGHT button.
Preset Camera Position
Store up to 200 Camera Presets (Position, zoom, focus
and back round lighting)
- Using the remote – 9 Presets are available
- 200 Presets can be set by using User Defined protocol
Set Preset using the remote control
- Make sure the STANDBY LED is not blinking. If the
STANDBY LED is blinking, please press PAN-TILT RESET
to reset.
- Adjust the cameras position, zoom, focus and back round
light.
- Press and hold the PRESET button, and then press one
of the POSITION 1-9 buttons.

Alfatron ALF-10XU2-CAM
7
Use Preset Position
Press any of the 1-9 buttons to activate that preset.
To Cancel Preset Position
Press RESET, then Press the Preset number you want to
cancel.
Bottom Switch
The bottom switch allows you to set the camera image right way up or, mounted to the
ceiling and the image flipped.
RS-232 or RS422/485 selection.

Alfatron ALF-10XU2-CAM
8
Menu Description
CAMERA ID
This setting allows you to set the camera ID. Press
the right arrow button and enter. Press Up or Down
to select the ID. Then click the right button to
confirm. Left to exit.
PROTOCOL
This setting allows you to set the cameras Baud
Rate. Press the right arrow button and enter. Press
Up or Down to select the protocol. Then click the
right button to confirm. Left to exit.
BAUD RATE
This setting allows you to set the camera control protocol. Press the right arrow button
and enter. Press Up or Down to select the baud rate. Then click the right button to
confirm. Left to exit.
IR SPEED
This setting allows you to set the camera Pan / Tilt Speed. Press the right arrow button
and enter. Press Up or Down to select the speed. Then click the right button to confirm.
Left to exit. There are 18 levels.
CAMERA SETTING – VIDEO MODE
This setting allows you to set the video format. Press the right arrow button and enter.
Press Up or Down to select. Then click the right button to confirm. Left to exit.
LOAD DEFAULTS
This setting allows you to set the camera control protocol. Press the right arrow button
and enter. Press Up or Down to select. Then click the right button to confirm. Left to
exit.

Alfatron ALF-10XU2-CAM
9
SAVE AND EXIT
This setting allows you to set the camera control protocol. Press the right arrow button
and enter. Press Up or Down to select. Then click the right button to confirm. Left to
exit.
DIGITAL ZOOM
This setting allows you to turn digital zoom on or off.
Press the right arrow button and enter. Press Up or
Down to select. Then click the right button to
confirm. Left to exit.
SHARPER LEVEL
This setting allows you to set the sharpness level.
Press the right arrow button and enter. Press Up or
Down to select. Then click the right button to
confirm. Left to exit. There are 15 levels
DNR LEVEL
This setting allows you to turn on / off the DNR Level. Press the right arrow button and
enter. Press Up or Down to select. Then click the right button to confirm. Left to exit.
BRIGHT COMP
This setting allows you to set the brightness. Press the right arrow button and enter.
Press Up or Down to select. Then click the right button to confirm. Left to exit. There
are 200 levels.
WB SETTING (White Balance)
This setting allows you to set the white balance. Press the right arrow button and enter.
Press Up or Down to select. Then click the right button to confirm. Left to exit. There
are 7 modes: WBS AUTO, SODIUM, AUTO, MANUAL, ATW, ONE PUSH, OUTDOOR
and INDOOR
When option is set to MANUAL: you can adjust the R/BGAIN. There are 15 Levels.

Alfatron ALF-10XU2-CAM
10
COLOR GAIN
This setting allows you to set the color gain. Press the right arrow button and enter.
Press Up or Down to select. Then click the right button to confirm. Left to exit. There
are 200 Levels.
COLOR HUE
This setting allows you to set the color hue. Press the right arrow button and enter.
Press Up or Down to select. Then click the right button to confirm. Left to exit. There
are 200 Levels.
CONTRAST
This setting allows you to set the contrast. Press the right arrow button and enter. Press
Up or Down to select. Then click the right button to confirm. Left to exit.

Alfatron ALF-10XU2-CAM
11
Technical Specifications

Alfatron ALF-10XU2-CAM
12
Limited warranty in respect of Alfatron Products Only
1.1 This limited warranty covers defects in materials and workmanship in this product.
1.2 Should warranty service be required, proof of purchase must be presented to the
Company. The serial number on the product must be clearly visible and not have been
tampered with in any way whatsoever.
1.3 This limited warranty does not cover any damage, deterioration or malfunction
resulting from any alteration, modification, improper or unreasonable use or
maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire,
improper packing and shipping (such claims must be presented to the carrier),
lightning, power surges, or other acts of nature. This limited warranty does not cover
any damage, deterioration or malfunction resulting from the installation or removal of
this product from any installation, any unauthorized tampering with this product, any
repairs attempted by anyone unauthorized by the Company to make such repairs, or
any other cause which does not relate directly to a defect in materials and/or
workmanship of this product. This limited warranty does not cover equipment
enclosures, cables or accessories used in conjunction with this product.
This limited warranty does not cover the cost of normal maintenance. Failure of the
product due to insufficient or improper maintenance is not covered.
1.4 The Company does not warrant that the product covered hereby, including, without
limitation, the technology and/or integrated circuit(s) included in the product, will not
become obsolete or that such items are or will remain compatible with any other
product or technology with which the product may be used.
1.5 Only the original purchaser of this product is covered under this limited warranty.
This limited warranty is not transferable to subsequent purchasers or owners of this
product.
1.6 Unless otherwise specified, the goods are warranted in accordance with the
manufacturer’s product specific warranties against any defect attributable to faulty
workmanship or materials, fair wear and tear being excluded.
1.7 This limited warranty only covers the cost of faulty goods and does not include the
cost of labor and travel to return the goods to the Company’s premises.
1.8 In the event of any improper maintenance, repair or service being carried out by
any third persons during the warranty period without the Company’s written
authorization, the limited warranty shall be void.
1.9 A 7 (seven) year limited warranty is given on the aforesaid product where used
correctly according to the Company’s instructions, and only with the use of the
Company’s components.

Alfatron ALF-10XU2-CAM
13
1.10 The Company will, at its sole option, provide one of the following three remedies to
whatever extent it shall deem necessary to satisfy a proper claim under this limited
warranty:
1.10.1 Elect to repair or facilitate the repair of any defective parts within a reasonable
period of time, free of any charge for the necessary parts and labor to complete the
repair and restore this product to its proper operating condition.; or
1.10.2 Replace this product with a direct replacement or with a similar product deemed
by the Company to perform substantially the same function as the original product; or
1.10.3 Issue a refund of the original purchase price less depreciation to be determined
based on the age of the product at the time remedy is sought under this limited
warranty.
1.11 The Company is not obligated to provide the Customer with a substitute unit
during the limited warranty period or at any time thereafter.
1.12 If this product is returned to the Company this product must be insured during
shipment, with the insurance and shipping charges prepaid by the Customer. If this
product is returned uninsured, the Customer assumes all risks of loss or damage
during shipment. The Company will not be responsible for any costs related to the
removal or re-installation of this product from or into any installation. The Company will
not be responsible for any costs related to any setting up this product, any adjustment
of user controls or any programming required for a specific installation of this product.
1.13 Please be aware that the Company’s products and components have not been
tested with competitor’s products and therefore the Company cannot warrant products
and/or components used in conjunction with competitor’s products.
1.14 The appropriateness of the goods for the purpose intended is only warranted to
the extent that the goods are used in accordance with the Company’s installation,
classification, and usage instructions.
1.15 Any claim by the Customer which is based on any defect in the quality or condition
of the goods or their failure to correspond with specification shall be notified in writing to
the Company within 7 days of delivery or (where the defect or failure was not apparent
on reasonable inspection by the Customer) within a reasonable time after discovery of
the defect or failure, but, in any event, within 6 months of delivery.
1.16 If delivery is not refused, and the Customer does not notify the Company
accordingly, the Customer may not reject the goods and the Company shall have no
liability and the Customer shall pay the price as if the goods had been delivered in
accordance with the Agreement.
1.17 THE MAXIMUM LIABILITY OF THE COMPANY UNDER THIS LIMITED
WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE
PRODUCT