Alfrescoplus Single User manual

SINGLE / DOUBLE

STORAGE MODULE

AND

SINGLE

/

DOUBLE SINK MODULE

ASSEMBLY

INSTRUCTIONS

For further instruction, please visit:

www.alfrescoplus.com.au

04014 - 12/19

OR



SINGLE/DOUBLEMODULE

INSTRUCTIONS



ASSEMBLYMANUAL







AlsoIncluded(IfRequired)How

toInstallthesinkModule

OR



SINGLE/DOUBLEMODULE

INSTRUCTIONS



ASSEMBLYMANUAL







AlsoIncluded(IfRequired)How

toInstallthesinkModule

OR

Also included (if required)

- How to install the sink module.

2 | ALFRESCOPLUS™

WARNING! – THIS IS A PERMANENT

CONNECTION SYSTEM!

WHAT’S NEEDED?

Tools Required:

• Soft Sided Hammer (Not Included)

• Philips head screwdriver (Not Included)

• Allen Keys x 2 (Included)

WHAT’S IN THE BOX?

Box 1 of 4 = Bench-top

Box 2 of 4 = Panels

Box 3 of 4 = Frames

Box 4 of 4 = Doors

PARTS INCLUDED:

FRAMES

• Cabinet Frames (Various Profiles) x 12 + 1

CORNER PRONGS

• Three prong x 8

WHITE PANELS x 6 + 1

PLINTH FEET x 4

HARDWARE

• Screws, small (Stone Top Frame) x 8

• Screws, medium (Plinth Feet) x 16

• Joining Bolts (Male/Female) x 4

• Allen Keys x 2

• Shelf Adjuster Points x 4

• Door Hinge Set x 2 (If Single Door)

• Door Hinge Set x 4 (If Double Door)

Please note: Follow all instruction in

the same sequence, either building

the SINGLE/DOUBLE storage

modules or the SINGLE/DOUBLE

sink modules.

OR

SINGLE/DOUBLE STORAGE MODULE & SINGLE/DOUBLE SINK MODULE ASSEMBLY INSTRUCTIONS | 3

Essential TIP: Ensure you have a stable flat surface or

workbench to work from. The most ideal height to assemble

the module is waist height. The workbench should be at least

1.8m (W) x 1m(H) x 0.7m(D) in size.

Remove all parts from the cartons. DO NOT

unwrap the frames at this stage.

Preparing the panels:

• Remove all the white panels from

the carton and place in an easily

accessible location (All red arrow labels

to face upwards).

• Remove at least 10cm of plastic film

alongside the edge of the panels, as per

image.

Essential TIP: DO NOT remove all the

plastic film from the panels, since the 4

way red arrows are an integral part of the

assembly process.

The red arrow stickers are placed on top of

the plastic on most panels and therefore the

plastic should not completely be removed

at this stage.

WHAT TO DO NEXT?

4 | ALFRESCOPLUS™

LAYOUT DIAGRAM



Whattodonext?



Removeallpartsfromthecartons.DONOTunwraptheframesatthisstage.



PreparingthePanels



vRemoveallthewhitepanelsfromthecartonandplaceinaneasilyaccessiblelocation.(Allredarrowlabelstoface

upwards).



FIG1



FIG. 1

SINGLE/DOUBLE STORAGE MODULE & SINGLE/DOUBLE SINK MODULE ASSEMBLY INSTRUCTIONS | 5

ASSEMBLING BACK PANEL



AssemblingSideWallPanelstoBackPanel

FIG2

FIG3

FIG4

FIG5

ShelfAdjuster

FIG6

FIG7

AssemblingBackPanel

AssemblingShelvePanel



AssemblingSideWallPanelstoBackPanel

FIG2

FIG3

FIG4

FIG5



ShelfAdjuster

FIG6

FIG7

AssemblingBackPanel

AssemblingShelvePanel



AssemblingSideWallPanelstoBackPanel

FIG2

FIG3

FIG4

FIG5

ShelfAdjuster

FIG6

FIG7

AssemblingBackPanel

AssemblingShelvePanel



AssemblingSideWallPanelstoBackPanel

FIG2

FIG3

FIG4

FIG5

ShelfAdjuster

FIG6

FIG7

AssemblingBackPanel

AssemblingShelvePanel

ASSEMBLING SIDE WALL PANELS TO BACK PANEL

ASSEMBLING SHELVE PANEL

FIG. 2 FIG. 3

FIG. 4 FIG. 5



AssemblingSideWallPanelstoBackPanel

FIG2

FIG3

FIG4

FIG5

ShelfAdjuster

FIG6

FIG7

AssemblingBackPanel

AssemblingShelvePanel

Shelf Adjuster

FIG. 6 FIG. 7



AssemblingSideWallPanelstoBackPanel

FIG2

FIG3

FIG4

FIG5

ShelfAdjuster

FIG6

FIG7

AssemblingBackPanel

AssemblingShelvePanel

6 | ALFRESCOPLUS™

ASSEMBLING THE ADJUSTABLE PLINTH FEET

No Allocating holes are used for plinth feet since the inside frame edge provides the guide.

Place Plinth foot into corner of cabinet frame. Screw down with screws provided. If easier,

remove plinth shaft from baseplate then screw down base plate first. If desired move the

front two plinth feet further back to create a deeper kick-plate position.



NoAllocatingholesareusedforplinthfeetsincetheinsideframeedgeprovidestheguide.PlacePlinthfootintocornerof

cabinetframe.Screwdownwithscrewsprovided.Ifeasier,removeplinthshaftfrombaseplatethenscrewdownbase

platefirst.Ifdesiredmovethefronttwoplinthfeetfurtherbacktocreateadeeperkick-plateposition.

FIG8



FIG9



AssemblingtheAdjustablePlinthFeet

FIG. 8

FIG. 9

SINGLE/DOUBLE STORAGE MODULE & SINGLE/DOUBLE SINK MODULE ASSEMBLY INSTRUCTIONS | 7

ATTACHING THE KICK PLATE

Please take note that the Kick plate provided is reversible, thereby giving you the choice

between a black “shadow line” finish or stylish silver finish. The Kick plate Biscuit is used to

connect onto more than one cabinet, thereby aligning the kick plate.



 



PleasetakenotethattheKickplateprovidedisreversible,therebygivingyouthechoicebetweenablack“shadowline”

finishorstylishsilverfinish.TheKickplateBiscuitisusedtoconnectontomorethanonecabinet,therebyaligningthekick

plate.



AttachingtheKickPlate

FIG11



FIG10



FIG12



FIG. 10

FIG. 11 FIG. 12

8 | ALFRESCOPLUS™

Choose the desired color face of kick plate. (Silver or Black). No pre drilled holes are possible

due to this color choice. Self tapping screws are provided to attach the spring clip plate to

the kick panel. The dimensions on Fig. 11 can be used as a guide only since the position of the

plinth foot and the desired depth of the kick plate will vary depending on the choice of plinth

foot installation position by the end user.



FIG13



FIG. 13

ASSEMBLING DOOR & HINGES

• To attach the hinge plate use a standard or power Phillips head screw driver.

The allocating holes are pre drilled into the frame.

• Attach all four-hinge plates when attaching two doors. Attach the two-left hinge plates

when attaching a single door.

Attach provided

Hinge Plate x 4 and

self tapping screws.

FIG. 14

SINGLE/DOUBLE STORAGE MODULE & SINGLE/DOUBLE SINK MODULE ASSEMBLY INSTRUCTIONS | 9

Illustration on attaching hinges to door panels by using the self-tapping screws provided.

FIG. 15

Each door hinge includes a

spacing bracket

Place the spacing bracket

on the underside of the door

hinge before assembly

Screw the door hinge to the

door panel with the bracket

in place as shown

10 | ALFRESCOPLUS™



*DetailedINSTRUCTIONSonhowtocliponthedoorsusingclip-on-hinges.



 



Firstlyalignthefronthingesectionwiththefrontsectionofthehinge-plate,thenpressonthebackofthehinge-plate,an

audible“Click”shouldbeheardifthedoorhasbeencorrectlyhanged.Repeattheprocesstosecurethebottomhingeand

door.

Atthisstageyourprogressshouldlookliketheabove

image.Chooseanyseparatestyleofdoorhandleandfit

accordingtothemanufacturersinstructions.

Thedoorshouldfullyopenandcloseasnormal.

FIG16



FIG17



* Detailed INSTRUCTIONS on how to clip on the doors using clip-on-hinges.

Clamp hinge on to the mounting plate as

shown by direction arrow

Press down the hinge arm to lock the plate

as shown

The door can be quickly removed by

pushing the button

Unclipping the door from the mounting

plate leaves all adjustments unaltered

Firstly align the front hinge section with the front section of the hinge-plate, then press on

the back of the hinge-plate, an audible “Click” should be heard if the door has been correctly

hanged. Repeat the process to secure the bottom hinge and door.

Clip On Hinge Instructions:



*DetailedINSTRUCTIONSonhowtocliponthedoorsusingclip-on-hinges.



 



Firstlyalignthefronthingesectionwiththefrontsectionofthehinge-plate,thenpressonthebackofthehinge-plate,an

audible“Click”shouldbeheardifthedoorhasbeencorrectlyhanged.Repeattheprocesstosecurethebottomhingeand

door.

Atthisstageyourprogressshouldlookliketheabove

image.Chooseanyseparatestyleofdoorhandleandfit

accordingtothemanufacturersinstructions.

Thedoorshouldfullyopenandcloseasnormal.

FIG16



FIG17



FIG. 16 FIG. 17

The door should fully open and close

as normal.

At this stage your progress should look

like the above image. Choose any separate

style of door handle and fit according to the

manufacturers.



*DetailedINSTRUCTIONSonhowtocliponthedoorsusingclip-on-hinges.



 



Firstlyalignthefronthingesectionwiththefrontsectionofthehinge-plate,thenpressonthebackofthehinge-plate,an

audible“Click”shouldbeheardifthedoorhasbeencorrectlyhanged.Repeattheprocesstosecurethebottomhingeand

door.

Atthisstageyourprogressshouldlookliketheabove

image.Chooseanyseparatestyleofdoorhandleandfit

accordingtothemanufacturersinstructions.

Thedoorshouldfullyopenandcloseasnormal.

FIG16



FIG17



SINGLE/DOUBLE STORAGE MODULE & SINGLE/DOUBLE SINK MODULE ASSEMBLY INSTRUCTIONS | 11

STONE TOP PLACEMENT (G)

The frame and stone top is pre-assembled for your ease of assembly.

Essential TIP: Ensure the frames and stone table are positioned on a stable flat surface to

ensure alignment. Caution: The stone table is very heavy, and a 2-person lift is required.

WARNING! - The stone-top positioning and

alignment is the last step of assembling your

module and BBQ kitchen setup. The double side

VHB tape creates a very strong permanent bond

and cannot be moved once contact has been made.

Take note that the 3M VHB tape is a permanent Very High Strength adhesion. Align the front

of the frame with the BBQ front then lower onto the cabinet for a permanent bond.



Theframeandstonetopispre-assembledforyoureaseofassembly.



EssentialTip:Ensuretheframesandstonetablearepositionedonastableflatsurfacetoensurealignment.Caution:The

stonetableisveryheavy,anda2-personliftisrequired.







WARNING!: Thestone-toppositioningandalignmentisthelaststepofassemblingyourmoduleandBBQ

kitchensetup.ThedoublesideVHBtapecreatesaverystrongpermanentbondandcannotbemoved

oncecontacthasbeenmade.



StonetopPlacement

FIG18



Ensurethatthe

frontframeedgeof

thestonetopis

positionedto

createanoverhang

ofatleast20mm

FIG. 18

Ensure that the front frame edge of

the stone top is positioned to create an

overhang of at least 20mm

12 | ALFRESCOPLUS™

Gently lower the stone top and frame onto the module cabinet.

Ensure that both ends of the frame and stone are lowered in a

horizontal position thereby being flush with the Cabinet top frame.

Instead of using the 3M VHB tape you have the option to drill holes

from the inside of the cabinet and make use of screws (not provided)

to attach the stone top.

For Further instruction on door adjustment and leveling please visit:

www.alfrescoplus.com.au

FIG. 19



ForFurtherinstructionondooradjustmentandlevelingpleasevisit:_____________________________



Takenotethatthe3MVHBtapeisapermanentVeryHighStrengthadhesion.Alignthefrontoftheframewiththe

BBQfrontthenlowerontothecabinetforapermanentbond.



FIG19



Gentlylowerthestonetopandframeontothemodulecabinet.Ensurethatbothendsoftheframeandstoneare

loweredinahorizontalpositiontherebybeingflushwiththeCabinettopframe.Insteadofusingthe3MVHBtapeyou

havetheoptiontodrillholesfromtheinsideofthecabinetandmakeuseofscrews(NotProvided)toattachthestone

top.

SINGLE/DOUBLE STORAGE MODULE & SINGLE/DOUBLE SINK MODULE ASSEMBLY INSTRUCTIONS | 13

HOW TO INSTALL THE SINK MODULE

Step 1: Ensure that the top white panel

is NOT installed into the frame. This panel

is not provided with our standard sink

module however if you are converting a

single or double solid top module into a

sink top, then create a suitable cutout into

the top of the cabinet by using a hole saw

and jig saw if required.



 



 



HowtoInstalltheSinkModule

Step1:EnsurethatthetopwhitepanelisNOTinstalledintotheframe.Thispanelisnotprovidedwithourstandard

sinkmodulehoweverifyouareconvertingasingleordoublesolidtopmoduleintoasinktop,thencreateasuitable

cutoutintothetopofthecabinetbyusingaholesawandjigsawifrequired.

ThistopwhitepanelISprovidedinthe

singleanddoublesolidtopmodule.

Thisishowthesingleordoublesink

moduleshouldlookafterfullyassembled.

FIG20



FIG21



FIG22



 



 



HowtoInstalltheSinkModule

Step1:EnsurethatthetopwhitepanelisNOTinstalledintotheframe.Thispanelisnotprovidedwithourstandard

sinkmodulehoweverifyouareconvertingasingleordoublesolidtopmoduleintoasinktop,thencreateasuitable

cutoutintothetopofthecabinetbyusingaholesawandjigsawifrequired.

ThistopwhitepanelISprovidedinthe

singleanddoublesolidtopmodule.

Thisishowthesingleordoublesink

moduleshouldlookafterfullyassembled.

FIG20



FIG21



FIG22



FIG. 20

FIG. 21 FIG. 22

This top white panel is provided in the

single and double solid top module but do

not install for sink module.

This is how the single or double sink

module should look after fully assembled.



 



 



HowtoInstalltheSinkModule

Step1:EnsurethatthetopwhitepanelisNOTinstalledintotheframe.Thispanelisnotprovidedwithourstandard

sinkmodulehoweverifyouareconvertingasingleordoublesolidtopmoduleintoasinktop,thencreateasuitable

cutoutintothetopofthecabinetbyusingaholesawandjigsawifrequired.

ThistopwhitepanelISprovidedinthe

singleanddoublesolidtopmodule.

Thisishowthesingleordoublesink

moduleshouldlookafterfullyassembled.

FIG20



FIG21



FIG22



 



 



HowtoInstalltheSinkModule

Step1:EnsurethatthetopwhitepanelisNOTinstalledintotheframe.Thispanelisnotprovidedwithourstandard

sinkmodulehoweverifyouareconvertingasingleordoublesolidtopmoduleintoasinktop,thencreateasuitable

cutoutintothetopofthecabinetbyusingaholesawandjigsawifrequired.

ThistopwhitepanelISprovidedinthe

singleanddoublesolidtopmodule.

Thisishowthesingleordoublesink

moduleshouldlookafterfullyassembled.

FIG20



FIG21



FIG22



14 | ALFRESCOPLUS™



 



Step2:Installthestonetopasperthestepsprovided

Step3:Alignthesinkwiththeprecutholeinthestone

top.

Step4:Lowerthesinkintotheprecutholeinthestone.

Ifapermanentinstallationidrequiredliquidsilicone

adhesivemaybeusedunderthemetalflangeofthesink.

Step5:Placethesinktapintotheprecutholeprovided.

Screwthebaseofthetapintoplacebyscrewingfromthe

bottomofthesink.Yourtapwillthenbesecurelyin

position.Pleasenotearegisteredplumperisnow

requiredtoplumintoyourwatermains.

FIG23



FIG24



FIG25



FIG26



 



Step2:Installthestonetopasperthestepsprovided

Step3:Alignthesinkwiththeprecutholeinthestone

top.

Step4:Lowerthesinkintotheprecutholeinthestone.

Ifapermanentinstallationidrequiredliquidsilicone

adhesivemaybeusedunderthemetalflangeofthesink.

Step5:Placethesinktapintotheprecutholeprovided.

Screwthebaseofthetapintoplacebyscrewingfromthe

bottomofthesink.Yourtapwillthenbesecurelyin

position.Pleasenotearegisteredplumperisnow

requiredtoplumintoyourwatermains.

FIG23



FIG24



FIG25



FIG26



Step 2: Install the stone top as per the

steps provided

FIG. 24

Step 3: Align the sink with the pre cut hole

in the stone top.

Step 5: Place the sink tap into the pre cut

hole provided. Screw the base of the tap

into place by screwing from the bottom of

the sink. Your tap will then be securely in

position. Please note a registered plumper

is now required to plumb into your water

mains.



 



Step2:Installthestonetopasperthestepsprovided

Step3:Alignthesinkwiththeprecutholeinthestone

top.

Step4:Lowerthesinkintotheprecutholeinthestone.

Ifapermanentinstallationidrequiredliquidsilicone

adhesivemaybeusedunderthemetalflangeofthesink.

Step5:Placethesinktapintotheprecutholeprovided.

Screwthebaseofthetapintoplacebyscrewingfromthe

bottomofthesink.Yourtapwillthenbesecurelyin

position.Pleasenotearegisteredplumperisnow

requiredtoplumintoyourwatermains.

FIG23



FIG24



FIG25



FIG26



FIG. 23

FIG. 26



 



Step2:Installthestonetopasperthestepsprovided

Step3:Alignthesinkwiththeprecutholeinthestone

top.

Step4:Lowerthesinkintotheprecutholeinthestone.

Ifapermanentinstallationidrequiredliquidsilicone

adhesivemaybeusedunderthemetalflangeofthesink.

Step5:Placethesinktapintotheprecutholeprovided.

Screwthebaseofthetapintoplacebyscrewingfromthe

bottomofthesink.Yourtapwillthenbesecurelyin

position.Pleasenotearegisteredplumperisnow

requiredtoplumintoyourwatermains.

FIG23



FIG24



FIG25



FIG26



Step 4: Lower the sink into the pre cut hole

in the stone. If a permanent installation id

required liquid silicone adhesive may be

used under the metal flange of the sink.

FIG. 25

SINGLE/DOUBLE STORAGE MODULE & SINGLE/DOUBLE SINK MODULE ASSEMBLY INSTRUCTIONS | 15

HOW TO INSTALL A DOOR HANDLE

Take note that the door handles can be placed vertically or horizontally as preferred by you.

FIG. 31 FIG. 32

Remove the Double sided Tape from the inside of the handle. Ensure you align the edge of

the handle to the edge of the door before touching the tape to the door panel. Carefully

press the door handle to the door for a permanent adhesion.

FIG. 27 FIG. 28

FIG. 29 FIG. 30

Additional screws are provided for a very secure connection, although you need to drill your own

holes due to the handle having multiple possible positions as desired. These additional screw

fixtures and not required under normal use.

For any queries or assistance call:

Customer Service

Australia Only

1300 174 876

Hours of operation:

Monday to Friday 8am - 5pm

Do not return to place of purchase

Keep your purchase receipt, this will be required to make

any claims under the 12 month warranty

AlfrescoPlus SINGLE User manual

Popular Indoor Furnishing manuals by other brands